• 한국자동차공학회논문집
• /
• 제6권1호
• /
• pp.27-35
• /
• 1998

This study describes the influence of combustion parameters on the nitric oxide emission, such as injection timing, air flow rate, injected amount of fuel, and compression ratio of engine. In order to determine the influence factors on the nitric oxide emission, the experiment were investigated with various parameters of engine cycle. According to the results of this study, the retardation of injection timing and the increases of airflow rate, and the decreases of fuel injection amount reduce the nitric oxide concentration in the exhaust emissions. Also, the increases of compression ration of engine increase in the concentration of nitric oxide formation in the combustion chamber. The results of this study give a guideline to decrease the nitric oxide formation by using the simulation program.

• 한국콘크리트학회:학술대회논문집
• /
• 한국콘크리트학회 2009년도 춘계 학술대회 제21권1호
• /
• pp.27-28
• /
• 2009

건축물의 지진모의실험을 수행할 경우, 부재에 작용하는 전단력과 축력의 계측이 필요하다. 본 연구에서는 2축 전단, 1축 압축을 측정할 수 있는 Load Cell의 제작 및 Calibration법을 제시하고 있다.

• 한국콘크리트학회:학술대회논문집
• /
• 한국콘크리트학회 1997년도 가을 학술발표회 논문집
• /
• pp.679-684
• /
• 1997

In this study, compressive strengths of reinforced concrete compression members rehabilitated with C.F.L. were analyzed from the test. Test parameters are spacing, spliced length, and section area of rehabilitation material. Displacement, failure load were measured during test. The failure mode and ultimate load were analyzed from these measured data. Test result shows that closer spacing of C.F.L. is more effective. strengthening with 1-ply C.F.L. is more effective than that of specimen with 2-ply C.F.L. The compressive capacity of specimen spliced ($\pi$.D)/2 shows almost similar strength to that of non-spliced specimen. The ultimate load carrying capacity of specimen strengthened with C.F.L. is increased to 1.11~1.68 times of that of non-rehabilitation specimen.

• 한국전산구조공학회:학술대회논문집
• /
• 한국전산구조공학회 1995년도 가을 학술발표회 논문집
• /
• pp.1-8
• /
• 1995

This work presents a new method to deal with buckling constraints. The mathematical optimization process of truss structures proposed earlier by the author has been proved to be the most rigorous method. The inclusion of buckling constraints, however, gives rise to a new problem The allowable compression stress of a member changes from one design iteration to another. This changing stress limit creates a good deal of noise in selecting active constraints and makes the solution process unstable. This problem can be overcome by introducing relaxation parameters. This work, however, aims at establishing a more rigorous method by containing the allowable compression stress in the left hand side of the associated constraint.

• Steel and Composite Structures
• /
• 제5권5호
• /
• pp.407-420
• /
• 2005

This study presents the strength of braced and unbraced cold-formed steel wall frames consisting of several wall studs acting as columns, top and bottom tracks, and bracing members. The strength and the buckling mode of steel wall frames were found to be different due to the change of bracing type. In addition, the spacing of wall studs is a crucial factor to the strength of steel wall frames. The comparisons were made between the test results and the predictions computed based on AISI Code. The related specifications do not clearly provides the effective length factors for the member of cold-formed steel frame under compression. This paper proposes effective length factors for the steel wall frames based on the test results. A theoretical model is also derived to obtain the modulus of elastic support provided by the bracing at mid-height of steel wall frames in this research.

• Structural Engineering and Mechanics
• /
• 제81권2호
• /
• pp.231-242
• /
• 2022

Numerical solutions for the linear buckling behavior of thin-walled circular hollow section members (CHS) with and without longitudinal stiffeners are presented using the semi-analytical finite strip method (SAFSM) which is developed based on Marguerre's shallow shell theory and Kirchhoff's assumption. The formulation of 3-nodal line finite strip is presented. The CHS members subjected to uniform axial compression, uniform bending, and combination of compression and bending. The buckling behavior of CHS is investigated through buckling curves which relate buckling stresses to lengths of the member. Effects of longitudinal stiffeners are studied with the change of its dimensions, position, and number.

• 한국강구조학회 논문집
• /
• 제22권6호
• /
• pp.609-616
• /
• 2010

이 논문은 600MPa급 고강도강이 원형강관 건축구조용으로 이용될 때 중심압축재의 좌굴강도에 관하여 수치해석적으로 조사한 것이다. 600MPa급 고강도강의 소재인장시험 결과로부터 중심압축재의 좌굴강도를 산정하였으며, 좌굴강도 산정에는 Beam-Column이론에 근거한 방법과 Tangent Modulus 이론에 의한 양자의 방법을 이용하였다. 그리고 소성흐름이 없는 인장시험의 응력-변형도 관계를 비례한도의 크기와 비례한도에서 항복점에 이르는 접선계수의 기울기로 근사시키고 좌굴강도 미치는 영향인자를 조사하였다. 600MPa급 고강도강에 적용되는 현재의 건축기준은 압축재의 경우 항복강도 Fy값을 480Mpa 까지 상향조정하여도 무리가 없다고 사료된다.

• Structural Engineering and Mechanics
• /
• 제46권3호
• /
• pp.323-335
• /
• 2013

This work aims to study the effect of stiffener ties in the behavior of intermediate length open section Cold-Formed Steel (CFS) Columns under axial compression. A comparative study on the behaviour and strength of Cold Formed Steel Columns by changing the direction of projection of lips (i.e., inwards or outwards) are also done. In this work two types of sections were considered Type-I section with lip projecting outwards (hat) and Type-II section with lip projecting inwards (channel). The length of the columns is predicted by performing elastic buckling analysis using CUFSM software. The theoretical analysis is performed using DSM - S100;2007, AS/NZ: 4600-2005 and IS: 801-1975. The compression tests are carried out in a 400 kN loading frame with hinged-hinged end condition. The non-linear numerical analysis is performed using Finite Element software ANSYS 12.0 to simulate the experimental results. Extensive parametric study is carried out by varying the width and spacing of the stiffener ties. The results are compared; the effects of stiffener ties on behaviour and load carrying capacity on both types of columns are discussed.

• Structural Engineering and Mechanics
• /
• 제72권5호
• /
• pp.569-583
• /
• 2019

Tubular steel sections are widespread all over the world because of their strength and aesthetic appearance. Tubular steel members may exhibit local buckling such as elephant foot or overall buckling under extreme compression load. Recently, external bonding of fiber reinforced polymers (FRP) sheets for strengthening these members has been explored through experimental research. This paper presents three-dimensional nonlinear finite element analysis (FEA) to investigate the structural behavior of strengthening tubular steel members with FRP against local and overall buckling phenomena. Out-of-roundness and out-of-straightness imperfections were introduced to the numerical models to simulate the elephant foot and overall buckling, respectively. The nonlinear analysis preferences such as the integration scheme of the shell elements, the algorithm for solution of nonlinear equations, the loading procedure, the bisection limits for the load increments, and the convergence criteria were set, appropriately enough, to successfully track the sophisticated buckling deformations. The agreement between the results of both the presented FEA and the experimental research was evident. The FEA results demonstrated the power of the presented rigorous FEA in monitoring the plastic strain distribution and the buckling phenomena (initiation and propagation). Consequently, the buckling process was interpreted for each mode (elephant foot and overall) into three sequential stages. Furthermore, the influence of FRP layers on the nonlinear analysis preferences and the results was presented.

• 소성∙가공
• /
• 제19권7호
• /
• pp.411-415
• /
• 2010

A sandwich panel which is comprised of truss cores faced with solid face sheets is lightweight and multi-functional. So it is widely used to not only structural material but also heat transfer media in transportation field such as airplane, train and vessel. There are various core topologies such as pyramidal and tetrahedral truss, square honeycombs and kagome truss. The study focused on analytical approach to optimize compression and shear quality of the unit cell of PCM with pyramidal configuration. With various unit cell models which have the same core weight per unit area but different truss member angle, analytical solution for effective stress ($\bar{\sigma},\bar{\tau}$), peak stress ($\bar{\sigma}_{peak},\bar{\tau}_{peak}$) by yielding and buckling, relative density ($\bar{\rho}_c$) and effective stiffness ($\bar{E},\bar{G}$) have been computed and compared each other. With this approach, the most optimal core configuration was predicted. The result has become the efficient guidelines for the design of PCM core structure.