• Steel and Composite Structures
• /
• 제50권3호
• /
• pp.363-374
• /
• 2024

The fatigue life of steel wire is affected not only by fatigue load, but also by corrosion environment in service period. Specially, the corrosion pit will lead to stress concentration on the surface of steel wire inducing the formation of fatigue cracks, and the fatigue cracks will accelerate the corrosion process. Therefore, the corrosion fatigue of steel wire is a coupling effect. In this study, the corrosion-fatigue coupling life curve is derived with considering corrosion-fatigue pitting stage, corrosion-fatigue short crack stage and corrosion-fatigue long crack stage. In addition, the stress concentration factors of different corrosion pits are calculated by COMSOL software. Furthermore, the effect of corrosion environment factors, that is, corrosion rate, corrosion pit morphology, frequency and action factor of fatigue load, on fatigue life of steel wire is analyzed. And then, the corrosion-fatigue coupling life curve is compared with the fatigue life curve and fatigue life curve with pre-corrosion. The result showed that the anti-fatigue performance of the steel wire with considering corrosion-fatigue coupling is 68.08% and 41.79% lower than fatigue life curve and fatigue life curve with pre-corrosion. Therefore, the corrosion-fatigue coupling effect should be considered in the design of steel wire.

• 대한산업공학회지
• /
• 제21권4호
• /
• pp.529-540
• /
• 1995

The paper deals with a procedure for constructing a composite surface interpolating a polygonal curve mesh defined from 3D scattered points. The procedure consists of a poly-angulation, construction of a curve net, and interpolation of the curve net. The poly-angulation contains a stage that changes a triangular edge net obtained from a triangulation into a poly-angular edge net. A curve net is constructed by replacing edges on the edge net with cubic Bezier curves. Finally, inside of an n-sided polygon is interpolated by n subdivided triangular subpatches. The method interpolates given point data with relatively few triangular subpatches. For an n-sided polygon, our method constructs an interpolant with n subdivided triangular subpatches while the existing triangular surface modeling needs 3(n-2) subpatches. The obtained surface is composed of quartic triangular patches which are $G^1$-continuous to adjacent patches.

• 한국복합재료학회:학술대회논문집
• /
• 한국복합재료학회 2005년도 춘계학술발표대회 논문집
• /
• pp.76-79
• /
• 2005

Bending deformation and energy absorption characteristics of aluminum-composite hybrid tube beams have been analyzed for improvement in the bending performance of aluminum space frame by using experimental tests combined with theoretical and finite element analyses. Hybrid tube beams composed of glass fabric/epoxy layer wrapped around on aluminum tube were made in autoclave with the recommended curing cycle. Basic properties of aluminum material used for initial input data of the finite element simulation and theoretical analysis were obtained from the true stress-true strain curve of specimen which had bean extracted from the Al tube beam. A modified theoretical model was developed to predict the resistance to the collapse of hybrid tube beams subjected to a bending load. Theoretical moment-rotation angle curves of hybrid tube beams were in good agreement with experimental ones, which was comparable to the results obtained from finite element simulation. Hybrid tube beams strengthened by composite layer on the whole web and flange showed an excellent bending strength and energy absorption capability.

• 한국복합재료학회:학술대회논문집
• /
• 한국복합재료학회 2004년도 추계학술발표대회 논문집
• /
• pp.258-263
• /
• 2004

An efficient technique for the calculation of guided wave dispersion curves in composite pipes is presented. The technique uses a forward-calculating variational calculus approach rather than the guess and iterate process required when using the more traditional partial wave superposition technique The formulation of each method is outlined and compared. The forward-calculating formulation is used to develop finite element software for dispersion curve calculation. Finally, the technique is used to calculate dispersion curves for several structures, including an isotropic bar, two multi-layer composite bars, and a composite pipe.

• Steel and Composite Structures
• /
• 제1권3호
• /
• pp.355-376
• /
• 2001

An experimental research program on end-plate beam-to-column composite joints under cyclic loading is presented. The major focus relates to the identification of the contribution of the concrete confinement in composite columns to the behaviour of the joint, on internal nodes and external nodes, together with an assessment of degradation of strength and stiffness in successive loading cycles. From the experimental results it was possible to identify the various failure modes and to fit the corresponding hysteretic curves to the Richard-Abbott and Mazzolani models. These curve-fitting exercises highlighted the need to adapt both models, either for improved ease of application, or to deal with some aspects previously not covered by those models.

• Nuclear Engineering and Technology
• /
• 제51권7호
• /
• pp.1822-1827
• /
• 2019

Mechanical responses and failure behaviors of advanced C/C composite tube are very important for structural component design in nuclear reactor. In this study, an experimental investigation was conducted to study mechanical properties of C/C composite tube. Quasi-static compression loading was applied to a type of advanced composite tube to determine the response of the quasi-static load displacement curve during progressive damage. Acoustic emissions (AE) signals were captured and analyzed to characterize the crack formation and crack development. In addition, the crack propagation of the specimens was monitored by imaging technique and failure mode of the specimen was analyzed. FEM is appled to simulate the stress distribution. Results show that advanced C/C composite tube exhibits considerable energy absorption capability and stability in load-carrying capacity.

• Journal of Electrical Engineering and Technology
• /
• 제7권5호
• /
• pp.698-704
• /
• 2012

This paper proposes a new methodology for evaluating the probabilistic reliability based grid expansion planning of composite power system including the Wind Turbine Generators. The proposed model includes capacity limitations and uncertainties of the generators and transmission lines. It proposes to handle the uncertainties of system elements (generators, lines, transformers and wind resources of WTG, etc.) by a Composite power system Equivalent Load Duration Curve (CMELDC)-based model considering wind turbine generators (WTG). The model is derived from a nodal equivalent load duration curve based on an effective nodal load model including WTGs. Several scenarios are used to choose the optimal solution among various scenarios featuring new candidate lines. The characteristics and effectiveness of this simulation model are illustrated by case study using Jeju power system in South Korea.

• Tribology and Lubricants
• /
• 제23권4호
• /
• pp.149-155
• /
• 2007

The CAD model of a elliptical gear for wire cutting has been developed. The rolling contact of pitch ellipses whose rotation axes coincide with their focus has been analyzed, and the perimeter of the pitch ellipse has been divided into equal-length segments by the number of teeth. A master tooth profile, which is a composite curve of circular arcs that represents involute, has been introduced. The elliptical gear has been designed by imposing the master tooth on the divided points of the pitch ellipse, and a full fillet has been achieved between neighbour teeth. Thus, the whole profile of an elliptical gear is a composite curve of arcs only, and consequently NC codes for wire cutting can be easily generated. Furthermore, a computer simulation program is developed to verify the mesh of the elliptical gear.

• 한국CDE학회논문집
• /
• 제4권3호
• /
• pp.269-283
• /
• 1999

Surface/surface intersection is a common and important problem in geometric modeling and CAD/CAM. Several methods have been used to approach this problem. All possible intersection curves can be obtained by using the subdivision algorithm, while it requires a great deal of memory and is somewhat inefficient. The tracing algorithm is much faster than the subdivision algorithm, and can find points on the intersection curve sequentially. But, the tracing algorithm has some problems in the intersection curves on surface boundaries. In this paper, an Improved tracing algorithm that includes some ideas such as a new trace-terminating condition for the intersection curves on surface boundaries, detecting closed intersections and extension for composite surfaces is suggested. This algorithm consists of three step: generating state points for curve tracing, tracing intersection curves and sorting pieces of the intersection curves. The results of this algorithm and comparisons to the 'DESIGNBASE' and 'ACIS' system are presented.

• 한국초전도ㆍ저온공학회논문지
• /
• 제3권2호
• /
• pp.1-4
• /
• 2001

For the practical use of a superconducting wire to magnet application, it is important to assess the Young modulus and other mechanical properties of HTS tapes. In order to establish a test method of mechanical properties for oxide composite superconductors. tensile tests of Bi-2223 multi- filamentary tapes were carried out at room temperature, as an activity of the International round robin test proposed by the committee of VAMAS/TWA 16-Subrgroup. The tapes consisting of mutli-filamentary showed a three stage tensile behavior. At the initial stage of the stress-streain curve. The elastic deformation existed in a quite nattrow strain region. But the plastic deformation was observed in a wide strain region due to the platic flow of the Ag alloy matrix. The results of RRT were also reported and discussed.