• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2005.07a
• /
• pp.35-37
• /
• 2005

100, 200nm 크기의 colloidal silica 각각에 나노 ceria 입자를 수열합성법으로 코팅하였다. Colloidal silica 입자에 ceria를 코팅 시 slurry의 pH조절과 수열처리에 이용하여 silica에 ceria가 코팅됨을 TEM과 zeta-potential을 이용하여 확인하였다. 연마 슬러리의 분산 안정성과 연마효율을 높이기 위하여 슬러리의 pH 는 9로 하였으며, 이때의 zeta-potential 값은 -25 mV이었다. 1 wt%로 제조된 연마슬러리를 이용하여, 4 inch $SiO_2$, $Si_3N_4$ wafer를 압력변화에 따른 연마특성을 관찰 하였다. Ceria coated colloidal silica 100 nm, 200 nm와 commercial한 $CeO_2$입자를 연마압력 6 psi로 oxide film을 연마한 결과 연마율이 각각 2490 ${\AA}/min$, 4200 ${\AA}/min$, 4300 ${\AA}/min$으로 측정되었다. 또한 $SiO_2$, $Si_3N_4$ film의 6 psi압력에서 ceria coated colloidal silica 100 nm, 200 nm와 commercial 한 $CeO_2$입자의 선택비는 3, 3.8, 6.7 이었다. 입자크기가 클수록 연마율이 높으며, Preston equation을 따라 연마 압력과 연마율이 비례하였다.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2006.06a
• /
• pp.571-572
• /
• 2006

Tungsten CMP needs interconnect of semiconductor device ULSI chip and metal plug formation, CMP technology is essential indispensable method for local planarization. This Slurry development also for tungsten CMP is important, slurry of metal wiring material that is used present is depending real condition abroad. It is target that this research makes slurry of efficiency that overmatch slurry that is such than existing because focus and use colloidal silica by abrasive particle to internal production technology development. Compared selectivity of slurry that is developed with competitor slurry using 8" tungsten wafer and 8" oxide wafer in this experiment. And removal rate measures about density change of $H_2O_2$ and Fe particle. Also, corrosion potential and current density measure about Fe ion and Fe particle. As a result, selectivity find 83:1, and expressed similar removal rate and corrosion potential and current density value comparing with competitor slurry.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.38 no.9
• /
• pp.1037-1041
• /
• 2014

Slurry used for polishing semiconductors processed by exchange, pressurization, and multi-step feeding has been studied to investigate the effect of the size and shape of slurry particles on the oxide CMP removal rate. First, spherical silica sol was prepared by the ion exchange method. The spherical silica particle was used as a seed to grow non-spherical silica sol in accordance with the multi-step feeding of silicic acid by the ion exchange and pressurization methods. The oxide removal rate of both non-spherical silica sol and commercially available slurry were compared with increasing average particle size in the oxide CMP. The more alkaline the pH level of the non-spherical silica sol, the higher was the removal rate and non-uniformity.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2008.06a
• /
• pp.361-362
• /
• 2008

• Korean Journal of Materials Research
• /
• v.15 no.6
• /
• pp.426-430
• /
• 2005

Chemical mechanical polishing (CMP) is an essential process in the production of integrated circuits containing copper interconnects. The effect of alanine in reactive slurries representative of those that might be used in copper CMP was studied with the aim of improving selectivity between copper(Cu) film and tantalum-nitride(TaN) film. We investigated the pH effect of nano-colloidal silica slurry containing alanine through the chemical mechanical polishing test for the 8(inch) blanket wafers as deposited Cu and TaN film, respectively. The copper and tantalum-nitride removal rate decreased with the increase of pH and reaches the neutral at pH 7, then, with the further increase of pH to alkaline, the removal rate rise to increase soddenly. It was found that alkaline slurry has a higher removal rate than acidic and neutral slurries for copper film, but the removal rate of tantalum-nitride does not change much. These tests indicated that alanine may improve the CMP process by controlling the selectivity between Cu and TaN film.

• Journal of the Semiconductor & Display Technology
• /
• v.6 no.4
• /
• pp.33-38
• /
• 2007

Quartz glass panel was prepared by a colloidal silica through the heat-treatment only without any additives in wet-chemical method. This colloidal silica used in slurry process has the uniform distribution of particle size and lower cost. The results show that 6N as a degree of purity and the 86 percentage of violet transmittance in 1mm thickness. AFM(Atomic Force Microscopy) pattern shows that the surface roughness are less than lnm. Also, we investigated the characteristic of quartz panel according to the concentration and distribution of hydroxyl group, viscosity and thermal expansion coefficient.

• Transactions on Electrical and Electronic Materials
• /
• v.7 no.4
• /
• pp.167-172
• /
• 2006

Submicron colloidal silica coated with ceria were prepared by mixing of silica and nano ceria particles and modified by hydrothermal reaction. The polishing efficiency of the ceria coated silica slurry was tested over oxide film on silicon wafer. By changing the polishing pressure in the range of $140{\sim}420g/cm^2$ with the ceria coated silica slurries in $100{\sim}300nm$, rates, WIWNU and friction force were measured. The removal rate was in the order of 200, 100, and 300 nm size silica coated with ceria. It was known that the smaller particle size gives the higher removal rate with higher contact area in Cu slurry. In the case of oxide film, the indentation volume as well as contact area gives effect on the removal rate depending on the size of abrasives. The indentation volume increase with the size of abrasive particles, which results to higher removal rate. The highest removal rate in 200 nm silica core coated with ceria is discussed as proper combination of indentation and contact area effect.

• Proceedings of the Korean Ceranic Society Conference
• /
• 2003.10a
• /
• pp.83.2-83
• /
• 2003

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.20 no.1
• /
• pp.74-79
• /
• 2007

Most studies on copper Chemical Mechanical Planarization (CMP) have focused on material removal and its mechanisms. Although many studies have been conducted on the mechanism of Cu CMP, a study on uniformity in Cu CMP is still unknown. Since the aim of CMP is global and local planarization, the approach to various factors related to uniformity in Cu CMP is essential to elucidate the Cu CMP mechanism as well. The main purpose of the experiment reported here was to investigate and mechanically analyze the roles of slurry components in the formation of the uniformity in Cu CMP. In this paper, Cu CMP was performed using citric acid($C_{6}H_{8}O_{7}$), hydrogen peroxide($H_{2}O_{2}$), colloidal silica, and benzotriazole($BTA,\;C_{6}H_{4}N_{3}H$) as a complexing agent, an oxidizer, an abrasive, and a corrosion inhibitor, respectively. All the results of this study showed that within-wafer non-uniformity(WIWNU) of Cu CMP could be controlled by the contents of slurry components.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.10 no.4
• /
• pp.309-317
• /
• 2000

Langasite is a promising new piezoelectric material for SAW filter application. Little was known until recently about the methods needed to mechanically polish and chemically polish/etch this material. In this experiment, polishing, slurry chemistry and chemical wet etching for langasite is described. Conventional quartz and LN ($LiNbO_3$) polishing methods did not produce satisfactory polished surfaces, and polishing with a colloidal silica slurries has shown to be most effective. The optimum condition was investigated by changing the slurry chemistry. As the planarization effect is very important in SAW filter applications, the examination of the effective particle number effect and the particle size effect was carried out. Z-cut langasite surface which had been polished with the colloidal silica slurries was etched in a variety of etchants. Conventional quartz etchants destroyed the polished surface. Other etchants formed a thin film on the surfaces. In this experiment, the reaction between langasite and a few etching solution was analysed. And an appropriate selective etchant solution for analyzing the defects was synthesized.