• Journal of the Korean institute of surface engineering
• /
• v.54 no.3
• /
• pp.124-132
• /
• 2021

Graphene which grown on the cobalt or nickel sputtered copper foil depending on the annealing time was studied. Graphene on the copper foil grown by chemical vapor deposition was compared to those on cobalt or nickel sputtered copper foil by using a RF (Radio Frequency) magnetron sputtering at room temperature. FLG(few-layer graphene) was identified independent of substrates by Raman and X-Ray Photoelectron Spectroscopy analyses. On copper foil, size and area fraction of the graphene growth increased until 30 minutes annealing and then didn't changed. Comparing to that, graphene on the cobalt refined till 50 minutes annealing, after then the effect disappeared which means a similar shape to that on copper foil. On nickel the graphene refined irrespective of annealing time that is possibly because of the complete solid solution of nickel with copper.

• Journal of the Korean Ceramic Society
• /
• v.33 no.4
• /
• pp.432-440
• /
• 1996

ZrO2 gel was prepared under pH 10 alkaline condition by sol-gel process and was investigated as a function of calcination temperature and effect of calcination temperature on cobalt adsorption capacity. The ZrO2 powder prepared by sol-gel process was calcined at 600, 800, 1000, 1200, 140$0^{\circ}C$ and analyzed by X-ray diffractometry. SEM specific surface area by BET nitrogen adsorption FT-IR and TG-DTA technique. It was shown that cobalt adsorption capacity of ZrO2 prepared under pH 10 alkaline condition and then calcined at $600^{\circ}C$ in high temperature was determined to be larger than that of ZrO2 at various calcination temperature. The specific surface area of ZrO2 calcined at $600^{\circ}C$ was 24.03m2/g and cobalt adsorption capacity at 25$0^{\circ}C$ high-temperature water was 0.16m-eq/g.

• Analytical Science and Technology
• /
• v.6 no.1
• /
• pp.57-63
• /
• 1993

Spectrophotometric determination of cobalt by flow injection method is described. 2-(5-Bromo-2-pyridylazo)-5-(N-propyl-N-sulfopropylamino) aniline rapidly forms a water-soluble complex with cobalt in $NH_3-NH_4Cl$ buffer solution at pH 10.5. The absorption maxima of this complex is at 545 nm with molar absorptivity of $58000L\;mol^{-1}\;cm^{-1}$. The calibration curve of cobalt is linear over the range of 0.1 to 0.6ppm and the detection limit is 25ppb. The relative standard deviation is ${\pm}0.72%$ for 0.5ppm and the sampling rate is $60samples\;hr^{-1}$. The interfering effect of some cations and anions was investigated. Ni(II), Cu(II), Fe(III) and $CN^-$ interfered severely. The interfering effect of these matallic ions could be decreased by adding $1.0{\times}10^{-3}M$ EDTA solution to the carrier stream.

• Proceedings of the Korean Society of Applied Pharmacology
• /
• 1998.11a
• /
• pp.140-140
• /
• 1998

The aim of this study was to find out the effect of hypoxic condition on the regulation of cyplal gene expression. pcyplal-Luc construct was cloned and transfected into Hepa I cells. When Hepa-I cells containing pcyplal-Luc were treated by DFO (desferrioxamine) which is iron-chelating agent, the stimulatory effect of luciferase by TCDD was decreased. This inhibitory effect of desferrioxamine on the luciferase activity was dose dependent and abolished by concomitant treatment with N$\^$G/-nitro-ι-arginine. And when cobalt chloride which is known as a hypoxia inducing chemical was administrated, the stimulatory effect of luciferase by TCDD was also decreased. This inhibitory effect of cobalt chloride on the luciferase activity was dose dependent and abolished by concomitant treatment with N$\^$G/-nitro-ι-arginine. These data showed that hypoxic condition down regulates cyplal gene expression and this might be through nitric oxide action.

• Journal of the Korean Magnetics Society
• /
• v.20 no.5
• /
• pp.182-186
• /
• 2010

Effect of cobalt substitution on the sintering behavior and magnetic properties of a NiZnCu ferrite was studied. $Ni_{0.36-x}Co_xZn_{0.44}Cu_{0.22}Fe_{1.98}O_4(0{\leq}x{\leq}0.04)$ ferrite was fabricated by a solid stat reaction method. It was proposed and experimentally verified that $Co^{2+}$ substituted NiZnCu ferrite was effective on improving the quality factor and magnetic properties of NiZnCu ferrites for multilayer chip inductors. The ferrite was sintered without sintering aids, at $880{\sim}920^{\circ}C$, for 2 h and the initial permeability, quality factor, density, shrinkage, saturation magnetization, and coercivity were also measured. The quality factor (Q) was increased linearly up to x = 0.01 and decreased rapidly over x = 0.01. As the cobalt content increased, the initial permeability and density of the ferrites decreases. The initial permeability of toroidal sample for $Ni_{0.35}Co_{0.01}Zn_{0.44}Cu_{0.22}Fe_{1.98}O_4$ ferrites sintered at $900^{\circ}C$ was 130 at 1 MHz and quality factor was 230.

• Nuclear Engineering and Technology
• /
• v.54 no.2
• /
• pp.627-636
• /
• 2022

In nuclear power plants and other nuclear facilities the removal of cobalt from radioactive liquid waste is needed to reduce the radioactivity concentration in effluents. In liquid wastes containing strong organic complexing agents such as EDTA cobalt removal can be problematic due to the high stability of the Co-EDTA complex. In this study, the removal of cobalt from NaNO₃ solutions using antimony oxide (Sb₂O₃) synthesized from potassium hexahydroxoantimonate was investigated in the absence and presence of EDTA. The uptake studies on the ion exchange material were conducted both in the dark (absence of UV-light) and under UV-C irradiation. Ca²⁺ or Ni²⁺ were included in the experiments as competing cations to test the selectivity of the ion exchanger. Results show that UV-C irradiation noticeably enhances the cobalt sorption efficiency on the antimony oxide. It was shown that nickel decreased the sorption of cobalt to a higher extent than calcium. Finally, the sorption data collected for Co²⁺ on antimony oxide was modeled using six different isotherm models. The Sips model was found to be the most suitable model to describe the sorption process. The Dubinin-Radushkevich model was further used to calculate the adsorption energy, which was found to be 6.2 kJ mol^-1.

• Journal of Energy Engineering
• /
• v.5 no.1
• /
• pp.56-64
• /
• 1996

The objective of this investigation is to establish the rejection characteristics of caesium and cobalt from radioactive liquid waste by chemical/ultrafiltration process. An extensive experimental investigation was conducted with inactive caesium and cobalt ions, utilizing ultrafiltration stirred cell. Caesium and cobalt could be effectively removed from waste solution using copper ferrocyanide and polyarcylic acid(PAA). The rejection dependence of the caesium was found to be a function of caesiun to potassium copper ferrocyanide feed molar ratio. The binding behavior of caesium on K$_2$Cu$_3$(Fe(CN)$\sub$6/)$_2$, particles was explained in terms of a Langmuir adsorption isotherm. When Cs/K$_2$Cu$_3$(Fe(CN)$\sub$6/)$_2$molar ratio was 1.5, the removal of caesium was the most efficient. The rejection efficiency of cobalt is dependent upon various parameters such as pH, cobalt concentration and PAA concentration. The rejection behavior of cobalt was explained in term of a equilibrium model taking into account the reaction between the ligand group, the proton and the cobalt ion. At the conditions of PAA/Co ratio of 2 and pH of 5.6, the removal of cobalt was over 90%. Also, the effect of chemical addition sequence for the simultaneously removal of caesiun and cobalt was discussed.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.21 no.10
• /
• pp.30-39
• /
• 2020

Single-phase barium ferrite powder was synthesized using the sol-gel method. At this time, an attempt was made to find the optimal experimental conditions for the production of single-phase barium ferrite by varying the Fe to Ba molar ratio (Fe/Ba) and the heat treatment temperature. In addition, cobalt-substituted barium ferrite particles were prepared using cobalt, which has an excellent effect on coercivity control for the production of ferrite fine particles having a coercivity of 2.5 to 5.5 kOe for use in high-density magnetic recording media. The changes in the magnetic properties of these were investigated. X-ray diffraction (XRD), thermogravimetric-differential thermal analysis (TG-DTA), and field emission scanning electron microscopy (FE-SEM) were used to observe the synthesis of single-phase, and Fourier transform infrared spectroscopy (FT-IR) and energy dispersive X-ray spectrometry (EDS) were used to analyze the chemical structure and composition. The coercivity of the cobalt-substituted barium ferrite powder was measured by vibrating sample magnetometry (VSM). As a result, single-phase Barium ferrites were synthesized when the Fe/Ba molar ratio was 10, and the heat treatment temperature was 900 ℃. The coercivity decreased with increasing the amount of Co added. Barium ferrite, having a coercivity of 2.5 to 5.5 kOe for use in high-density magnetic recording media, was synthesized when the Co to Fe(Co/Fe) molar ratio was less than 0.16.

• Korean Journal of Mineralogy and Petrology
• /
• v.36 no.2
• /
• pp.107-115
• /
• 2023

Cobalt can be released into the natural environment as industrial waste from the alloying industry and as acid mine drainage, and it is also a radionuclide (⁶⁰Co) that constitutes high-level radioactive waste. Smectite is a mineral that can be useful for adsorption and isolation of this element. In this study, Cheto-type montmorillonite (Cheto-MM), which is the source clays of The Clay Mineral Society (CMS) and already well-characterized, was used. The effect of the adsorption site affected by the presence of interlayer water on the adsorption of cobalt before and after dehydration by heating was evaluated and the adsorption mechanism of cobalt on Cheto-MM was studied by applying adsorption kinetics and adsorption isotherm models. The results showed that the adsorption characteristics changed with dehydration and subsequent shrinkage, and cobalt was found to be adsorbed at the edge of Cheto-MM for about 38% and adsorbed at the interlayer site for about 62%, suggesting that the cobalt adsorption of Cheto-MM is significantly influenced by the interlayer. By applying the adsorption kinetic models, the cobalt adsorption kinetics of Cheto-MM is explained by a pseudo-second-order model, and the concentration-dependent adsorption was best described by the Langmuir isotherm adsorption model. This study provides basic knowledge on the adsorption characteristic of cobalt on montmorillonite with different adsorption sites and is expected to be useful in predicting the adsorption behavior of smectite in high-level radioactive waste disposal sites in the future.

• Journal of Magnetics
• /
• v.10 no.3
• /
• pp.118-121
• /
• 2005

We have investigated the magnetic properties of electroplated thin Cu/Co multilayers by using electrolytes made of copper sulphate and cobalt sulphate and by applying alternating plating voltage. While the multilayers plated with pure electrolyte showed superparamagnetism, those plated with organic additives showed ferromagnetic behavior. These changes are attributed to the so-called 'self-annealing' effect and reduction of grain size caused by the organic additives.