• 한국기계가공학회지
• /
• 제15권2호
• /
• pp.118-124
• /
• 2016

In this study, experiments are conducted to improve spray coating uniformity by using second and third electrodes based on the electrospray atomization mechanism. The uniformity of fabricated thin films can be improved by adjusting the design of the second electrode. The implementation of the second electrode with an elongated hole and a bending angle of $90^{\circ}$ results in highly uniform films. In addition, induced area to substrate is increased by lowering the applied voltage using the third electrode with a round rod shape. A linear correlation between applied voltage and induced area is confirmed. Thin film thickness and surface roughness are measured after the fabrication of thin films through the electrospray process. It is confirmed that a thin film is formed having an average thickness of 273.44 nm, a thickness uniformity of less than 10%, and a surface roughness of 3 nm.

• 센서학회지
• /
• 제30권6호
• /
• pp.451-455
• /
• 2021

Porous copper bromide (CuBr) films are highly advantageous for detecting ammonia (NH₃). The fabrication of porous CuBr films requires complex high-temperature processes or multistep processes. Herein, we report the uncomplicated preparation of porous CuBr films by a spin-coating method and the films' excellent NH₃ sensing properties. The porous films were prepared by spin-coating 100, 150, and 200 mM CuBr solutions, and then dried in a vacuum oven for 2 h. All the films showed a high NH₃ response; in particular, the film prepared using a 100 mM CuBr solution showed an extremely high response (resistance ratio = 852) to 5 ppm NH₃. The film also showed fast response and recovery times, 272 s and 10 s respectively, even at room temperature. The outstanding NH₃ sensing characteristics were explained in relation to the porosity and thickness of the prepared films. The high-performance NH₃ sensors used in this study can be used for both indoor air quality and environmental monitoring applications.

• Transactions on Electrical and Electronic Materials
• /
• 제17권3호
• /
• pp.178-181
• /
• 2016

In this study a coating experiment was performed to fabricate blue light cut films, which represent a 390~430 nm cut off rate of more than 40% and a transmittance rate of more than 90%, using a roll-to-roll nano micro coating system. The study also analyzed the characteristics of the blue light cut films. Thus, the hardness, which is more than 3H, is ensured through fabricating films using a Sol-Gel process that will determine the proper hardness level. Also, the experiment shows excellent results by cutting blue light through a mixing blue light powder.

• 한국표면공학회지
• /
• 제28권2호
• /
• pp.77-82
• /
• 1995

In this study, we examined the relationships between the coating film's properties, such as microhardness, adhesion of coating fil $m_strate, and machining tool's life time. Samples were prepared by coating TiN on the 5.5 diameter twist drills using reactive ion plating technology, For measuring microhardness and adhesion of fil $m_strate, HSS plate was used for substrate. TiN coated drill's life time was dependent on the adhesion of fil $m_strate and averagely increased by several ten times more than uncoated drill's. The major parameter affecting TiN coated drill's life time was the strong adhesion between coating film and substrate.ate.

• 제어로봇시스템학회:학술대회논문집
• /
• 제어로봇시스템학회 2005년도 ICCAS
• /
• pp.1907-1910
• /
• 2005

Coating thickness is an important variable that plays a role in product quality, process control, and cost control. Measurement of film thickness can be done with many different instruments. In this paper, we introduce the new eddy current system for measure the thickness of nonconductive coatings on nonferrous metal substrates. The experimental results are shown that the proposed system is able to measure thickness of plastic film coating on aluminum plates in the range of 0 to 1000 microns with satisfy sensitivities, linearity, resolution and stability of the system.

• 한국세라믹학회지
• /
• 제44권10호
• /
• pp.585-588
• /
• 2007

Silicon nitride films for an anti-reflection coating were deposited on silicon via RF magnetron sputtering using a $Si_3N4$ target. The best result was obtained at the sputtering condition of 340 W RF power, 5 mtorr Ar atmosphere, $100^{\circ}C$ substrate temperature. The films showed 7.9% reflectance minimum with 2.35 refractive index. 0.21 absorption coefficient at 66.6 nm thickness. The surface morphology showed a smooth and dense film with good adhesion to silicon surface.

• Korea-Australia Rheology Journal
• /
• 제16권4호
• /
• pp.227-233
• /
• 2004

Simplified model of slide-fed curtain coating flow has been developed and tested in this study. It rests on the sheet profile equations for curtain thickness in curtain flow and its trajectory derived by the integral momentum balance approach of Higgins and Scriven (1979) and Kistler (1983). It also draws on the film profile equation of film thickness variation in flow down a slide. The equations have been solved in finite difference approximation by Newton iteration with continuation. The results show that how inertia (Rey­nolds number), surface tension (capillary number), inclination angle of the slide, and air pressure difference across the curtain affect sheet trajectory and thickness profile. It has been revealed that approximate models can be useful to easily analyze coating flow dynamics without complex computations, giving qualitative agreement with full theory and with experiment.

• 한국세라믹학회지
• /
• 제34권1호
• /
• pp.37-44
• /
• 1997

졸겔법중 딥코팅법을 이용하여 조성비 2Fe/Ba=5.25 졸로부터 바륨페라이트 박막을 제조하였다. 졸의 겔화과정은 4단계로 구분할 수 있으며, 8$0^{\circ}C$에서 90분간 반응시켜 제조한 졸이 코팅용 졸로서 가장 적합한 특성을 나타내었다. 박막층에 형성된 침상 형태의 입자들은 기판에 수평 하게 위치하고 있었으며, 박막 두께가 증가함에 따라 그 경향은 증가하였다. 침상형 입자의 자화용이축 방향은 장축 방향이었다.

• 한국정밀공학회지
• /
• 제31권6호
• /
• pp.491-495
• /
• 2014

We developed a compact high-precision slot-die coating machine for thin-film deposition on a flexible substrate. For smooth and precise coating, air-bearing and linear motor system were employed to minimize velocity ripple. The gap control mechanism is specially designed to have repeatability of gap between nozzle and substrate under 1 ${\mu}m$. Due to extremely precise gap control, the machine can coat thin-films down to 50 nm with $200mm{\times}100mm$ size. A thin film of Ag nano-particle ink is coated for demonstration.

• 약학회지
• /
• 제33권6호
• /
• pp.324-332
• /
• 1989

Drug release from sulfanilamide granules coated with a polyelectrlyte complex of sodium tripolyphosphate and chitosan was studied. The coating film thickness increased with increasing concentration of chitosan in the coating solution and the drug release rates of the coated granules were significantly reduced comparing with those of the uncoated granules. $T_{50%}$ of the uncoated granules was 6 minutes, but those of the granules coated with chitosan-sodium tripolyphosphate from 0.5, 0.7, and 0.9% (w/v) chitosan-HCl solution were 27, 135, and 180 minutes, respectively in distilled water. In dissolution medium at pH 6.8, $T_{50%}$ of the uncoated granules was 4 minutes, but those of the granules coated with chitosan-sodium tripolyphosphate from 0.5, 0.7, and 0.9(w/v)% chitosan-HCl solution, were 32, 135, and 160 minutes, respectively.