• The KIPS Transactions:PartA
• /
• v.10A no.3
• /
• pp.247-254
• /
• 2003

This paper describes a Delay Locked Loop (DLL) with low supply voltage and wide lock range for Synchronous DRAM which employs Double Data Rate (DDR) technique for faster data transmission. To obtain high resolution and fast lock-on time, a new type of phase detector is designed. The new counter and lock indicator structure are suggested based on the Dual-clock dual-data Flip Flop (DCDD FF). The DCDD FF reduces the size of counter and lock indicator by about 70%. The delay line is composed of coarse and fine units. By the use of fast phase detector, the coarse delay line can detect minute phase difference of 0.2 nsec and below. Aided further by the new type of 3-step vernier fine delay line, this DLL circuit achieves unprecedented timing resolution of 25psec. This DLL spans wide locking range from 500MHz to 500MHz and generates high-speed clocks with fast lock-on time of less than 5 clocks. When designed using 0.25 um CMOS technology with 1.8V supply voltage, the circuit consumes 32mA at 500MHz locked condition. This circuit can be also used for other applications as well, such as synchronization of high frequency communication systems.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.31 no.1C
• /
• pp.39-51
• /
• 2011

A large number of small particles may surround large gravels which are non-contact and dispersed within the ground. The strength of such soil may be influenced by the mechanical properties of a few coarse gravels. A specimen or gravel size can impact the shear characteristics of sand with dispersed gravels. In this study, the size of gravel and specimen varies and its effect on shear characteristics of a granular soil was evaluated. Five sizes of gravels with 7, 12, 15, 18, and 22 mm were used repeatedly and inserted in the middle of each compacted layer. A specimen consists of five or ten equal layers depending on gravel size, which is 5 cm or 10 cm in diameter and 10 cm or 20 cm in height. An embedded gravel ratio by weight is 3% and constant for all cases with gravel. After consolidation, a series of undrained triaxial compression tests under three confining pressures was performed on sand with dispersed gravels. The maximum deviator stress of a specimen with 10 cm in diameter was at average 30% higher than that with 5 cm in diameter and increased up to 90% for a specimen with gravel. When a gravel size of 7 and 12 mm used, the maximum deviator stress of a specimen with 10 cm in diameter was higher than that of one without gravel, whereas the maximum deviator stress of a specimen with 5 cm was higher or lower than that without gravel. The gravel size and specimen diameter influenced the undrained behavior of sand. The maximum deviator stress of a specimen with gravel either increased or decreased compared to that without gravel, depending on the ratio of gravel size to specimen diameter, 1/5.

• Journal of Korean Society for Atmospheric Environment
• /
• v.22 no.5
• /
• pp.590-603
• /
• 2006

Size-and time-resolved aerosol samples were collected using an eight-stage Davis rotating unit for monitoring (DRUM) sampler from 23 March to 29 April 2001 at Gosan, Jeju Island, Korea, which is one of the super sites of Asia-Pacific Regional Aerosol Characterization Experiment(ACE-Asia). These samples were analyzed using synchrotron X-ray fluorescence for 3-hr average concentrations of 19 elements including Al, Si, S, Cl, K, Ca, Ti, V, Cr, Mn, Fe, Ni, Cu, Zn, As, Se, Br, Rb, and Pb. The size-resolved data sets were then analyzed using the positive matrix factorization(PMF) technique to identify possible sources and estimate their contributions to particulate matter mass. PMF analysis uses the uncertainty of the measured data to provide an optimal weighting. Twelve sources were resolved in eight size ranges($0.09{\sim}12{\mu}m$) and included continental soil, local soil, sea salt, biomass/biofuel burning, coal combustion, oil combustion, municipal incineration, nonferrous metal source, ferrous metal source, gasoline vehicle, diesel vehicle, and volcanic emission. The PMF result of size-resolved source contributions showed that natural sources represented by local soil, sea salt, continental soil, and volcanic emission contributed about 79% to the predicted primary particulate matter(PM) mass in the coarse size range ($1.15{\sim}12{\mu}m$) while anthropogenic sources such as coal combustion and biomass/biofuel burning contributed about 58% in the fine size range($0.56{\sim}2.5{\mu}m$). The diesel vehicle source contributed mostly in ultra-fine size range($0.09{\sim}0.56{\mu}m$) and was responsible for about 56% of the primary PM mass.

• Journal of the Korean Society of Food Science and Nutrition
• /
• v.46 no.6
• /
• pp.730-738
• /
• 2017

In this study, we investigated the physicochemical properties of coffee brews according to coffee bean grinding grade. We also examined the effect of grinding grade on amounts of volatile flavor compounds. Coffee brew samples were separated using standard sieves (with pore sizes of 850, 600, and $425{\mu}m$), making particle sizes of ground beans as follows: whole bean (control), $850{\mu}m$ or more (coarse), $850{\sim}600{\mu}m$ (medium), $600{\sim}425{\mu}m$ (fine), and $425{\mu}m$ or less (very fine). For each particle size category, pH, total acidity, brown color intensity, chromaticity, total phenolic content, caffeine content, chlorogenic acid content, and total amounts of volatile flavor compounds generated were compared and analyzed. As grinding grade decreased, pH and brown color intensity increased from 4.84 to 5.18 and from 0.257 to 0.284, respectively, whereas total acidity decreased from 0.31 to 0.17%. As grinding grade decreased, the $L^*$ and $a^*$ color values decreased; however, $L^*$ value did not exhibit a significant difference depending on the grinding grade. The $b^*$ value was 15.75 in the very fine size category, which showed the highest yellowness. There was an 11 or higher color difference between the control and ground coffee powder, indicating a remarkable color difference. The total phenolic, caffeine, and chlorogenic acid contents of the coffee brewed from ground beans with a very fine size were 4.54 mg gallic acid equivalent/mL, $733.0{\mu}g/mL$, and $383.7{\mu}g/mL$, respectively, which were high values. The total amounts of volatile compounds in the very fine size category were found to be greater than 100 mg/kg. In this study, we suggest the basis for coffee quality evaluation, which involves evaluating changes in the physicochemical properties and amounts of flavor compounds of coffee relative to the grinding grade of the beans (basic step of coffee extraction).

• Analytical Science and Technology
• /
• v.27 no.1
• /
• pp.1-10
• /
• 2014

The $PM_{10}$ and $PM_{2.5}$ samples were collected at Gosan Site of Jeju Island, and analyzed, in order to investigate the size distribution and pollution characteristics of their components. $NH{_4}{^+}$, nss-$SO{_4}^{2-}$, $K^+$, and $CH_3COO^-$ were mostly existed in fine particles. Meanwhile, $NO{_3}{^-}$ was distributed in both fine and coarse particles, and $Na^+$, $Cl^-$, $Mg^{2+}$, nss-$Ca^{2+}$ were rich in coarse particle mode. The concentrations of nss-$Ca^{2+}$ and $NO{_3}{^-}$ were increased 36.7 and 3.2 times in coarse particles, and 15.0 and 3.1 times in fine particles during the Asian Dust periods. Especially, the concentrations of crustal elemental species such as Al, Fe, Ca, K, Mg, Ti, Mn, Sr, Ba were highly increased for those periods. In the haze events, the concentrations of secondary air pollutants were increased 1.3~2.6 and 1.5~4.2 times in coarse and fine particles, respectively. Moreover, the remarkable increase of $NO{_3}{^-}$ concentration was also observed in fine particle mode. The factor analysis showed that the composition of coarse particles was influenced mainly by marine sources, followed by soil and anthropogenic sources. On the other hand, the fine particles were influenced by anthropogenic sources, followed by marine and soil sources.

• Journal of Korean Society for Atmospheric Environment
• /
• v.23 no.6
• /
• pp.675-688
• /
• 2007

To characterize organic and elemental carbon (OC and EC), and water-soluble organic carbon (WSOC) contents, daily $PM_{2.5}$ measurements were performed in August 2006 (summer) and Jan $11{\sim}Feb$ 12 2007 (winter) at an urban site of Gwangju. Daily size-segregated aerosol samples were also collected for WSOC analysis. No clear seasonal variations in EC and WSOC concentrations were observed, while seasonal differences in OC concentration, and OC/EC and WSOC/EC ratios were shown. The WSOC/OC ratio showed higher value in summer (0.56) than in winter (0.40), reflecting the greater enhancement of secondary WSOC formation at the site in summer. Secondary WSOC concentrations estimated using EC tracer method were in the range $0.0{\sim}2.1\;{\mu}g/m^3$ (average $0.42\;{\mu}g/m^3$) and $0.0{\sim}1.1\;{\mu}g/m^3\;(0.24\;{\mu}g/m^3)$, respectively, accounting for $0{\sim}51.6%$ (average 16.8%) and $0{\sim}52.5%$ (average 13.1 %) of the measured WSOC concentrations in summer and winter. Sometimes higher WSOC/OC ratio in winter than that in summer could be attributed to two reasons. One is that the stable atmospheric condition often appears in winter, and the prolonged residence time would strengthen atmospheric oxidation of volatile organic compounds. The other is that decrease of ambient temperature in winter would enhance the condensation of volatile secondary WSOC on pre-existing aerosols. In summertime, atmospheric aerosols and WSOC concentrations showed bimodal size distributions, peaking at the size ranges $0.32{\sim}0.56\;{\mu}m$ (condensation mode) and $3.2{\sim}5.6\;{\mu}m$ (coarse mode), respectively. During the wintertime, atmospheric aerosols showed a bimodal character, while WSOC concentrations showed a unimodal pattern. Size distributions of atmospheric aerosols and WSOC with a peak in the size range $0.32{\sim}0.56\;{\mu}m$ were observed for most of the measurement periods. On January 17, however, atmospheric aerosols and WOSC exhibited size distributions with modal peaks in the size range $1.0{\sim}1.8\;{\mu}m$, suggesting that the aerosol particles collected on that day could be expected to be more aged, i.e, longer residence time, than the aerosols at other sampling periods.

• Journal of radiological science and technology
• /
• v.26 no.1
• /
• pp.39-44
• /
• 2003

The aim of this study is to evaluate a efficient w/v% barium suspension and w/v% sodium carboxy methyl cellulose (SCMC) for small bowel examination. Between november 2001 and june 2002, 370 patients were examined small bowel examination with oral administration of barium suspension mixed with SCMC. we classified into six groups including A(fine type 40% $BaSO_4$ mixed 0.5% SCMC and 600 ml 0.5% SCMC administration), B(fine type 30% $BaSO_4$ mixed 0.5% SCMC), C(fine type 20% $BaSO_4$ mixed 0.5% SCMC), D(fine type 25% $BaSO_4$ mixed 0.5% SCMC), E(D mixed coarse type 25% $BaSO_4$ mixed 0.5% SCMC), F(D mixed coarse type 25% $BaSO_4$ mixed 0.75% SCMC). We measured transparency rate of contrast media transit time, administration dose, viscosity and particle size. The transparency rate was higher then 80 kV and 90 kV in 100 kV in the same 20 mAs condition. Transit time was the fastest in A group(mean trans time 56 minutes) and the slowest in E group(mean 100 minutes), Administration dose was the smallest in A group(mean dose 541 ml and the most in E group(mean 1,100 ml), viscosity was the lowest in E(125.1 mpa/s) and the highest in A(375.5 mpa/s), and particle size was $1.0\;{\mu}m$ in A, B, C, and D group, $0.6\;{\mu}m,\;1.0\;{\mu}m,\;10.0\;{\mu}m$ in E, F group. In conclusion, we propose that the efficient condition for small examination is high voltage technique, high density $BaSO_4$, and 0.625% w/v SCMC.

• Journal of Environmental Health Sciences
• /
• v.33 no.5
• /
• pp.408-421
• /
• 2007

The concentration characteristics of atmospheric particle matters (PM) including $PM_{2.5},\;PM_{10}$, and TSP were evaluated through the measurement data of PM_{2.5}$ (fine particulate), PM_{10-2.5}$ (coarse particulate), and PM_{over-10}$ collected using a MCI (multi-nozzle cascade impactor) sampler of a three-stage filter pack in spring of 2006 in Iksan area. During the sampling period of 10-15 March and 24 days from 8 April to 2 May, 32 samples for PM of each size fractions were collected, and then measured for PM mass concentrations and water-soluble inorganic ion species. Average concentrations of $PM_{2.5},\;PM_{10}$, TSP were $57.9{\pm}44.1mg/m^3$, $96.6{\pm}89.1mg/m^3$, and $114.8{\pm}99.7mg/m^3$, respectively. Water-soluble inorganic ion fractions to PM mass were found to be 36.5%, 18.0%, and 11.1% for $PM_{2.5}$, $PM_{10-2.5}$ and $PM_{over-10}$, respectively. By showing the high concentrations of PM samples during Asian dust events, those three fractions of PM were distinguished between the samples of Asian dust event and the samples of no event. However, the increase of PM concentrations observed during Asian dust events showed a different pattern for some Asian dust events. The differences of those three fractions in the size distribution may depend on differences on place of occurrence of Asian dust storm and course of transport from China continent to Iksan area in Korea. However, the extent of PM mass contribution during Asian dust events was generally dominated by the coarse particles rather than the fine fraction of PM. The variations of water-soluble inorganic ion species concentration in those three PM fractions between the samples of Asian dust event and the samples of no event were also discussed in this study.

• Culinary science and hospitality research
• /
• v.18 no.3
• /
• pp.191-205
• /
• 2012

Due to a surplus of rice on the market, there has been a growing interest in developing better processed rice products, especially rice liquor or spirits which are popular and have a large market value. In this study, Takju was made with different varieties of rice and rice powder particle sizes, after which a taste survey was performed and measurements were taken on the characteristics of Takju including the temperature of the fermenting material, sugar content, alcohol content, acidity, amino acid types, colors, etc. The varieties of rice used in the study included Chucheong, Hiami and Anda. The temperature of the brew for each kind of Takju reached its highest point 48 hours after preparation. Differences among rice varieties were only apparent in the acidity and taste evaluations. The acidity was found to be highest with Anda, followed by Chuchoeng and Hiami. Chuchoeng had the highest taste evaluation scores. With regards to particle sizes, the alcohol content and acidity were found to be highest with coarse rice powder while ultra fine rice powder showed the highest fermenting temperature, sugar content, acidity, amino acid type, pH level, color and taste scores right after preparation. The results of this study suggest that among the kinds of Takju made from different rice varieties and particle sizes, the one made from Chucheong ultra fine rice powder is the most preferable over other variations.

• International Journal of Highway Engineering
• /
• v.17 no.3
• /
• pp.49-58
• /
• 2015

PURPOSES : The use of environmentally friendly construction methods has been recently encouraged to reduce fuel consumption and the effects of global warming. For this purpose, the roller compacted concrete pavement (RCCP) construction method has been developed. RCCP is more environmentally friendly and economically efficient than general concrete by reducing the amount of CO2 generated through the application of a smaller amount of cement. RCCP has a number of advantages such as an easy construction method, low cost, high structural hydration performance, and aggregate interlocking. However, mix design standards and construction guidelines of RCCP are required for domestic application. In addition, a study on aggregate selection, which has an effect on the characteristics of RCCP, is necessary owing to a limited number of researches. Thus, the aggregate effect on the performance of RCCP in securing the required strength and workability was evaluated in consideration of domestic construction. METHODS : Sand and coarse aggregates of both 19mm and 13mm in maximum size were used in this study. Four types of aggregate gradations (s/a = 30%, 58%, and 70% for the sand and coarse aggregate of 19mm in maximum size, and s/a = 50% for a combination of the three types of aggregates) were set up to investigate the effects of the PCA band on the RCC characteristics. The conditions of s/a = 30% and 70% were evaluated to check the gradation effect outside of the recommended band. The conditions of s/a = 58% and 50% were used because they are the optimum combination of the two and three types of aggregates, respectively. RCCP gradation band was suggested gradation with a proper construction method of RCCP by synthetically comparing and analyzing the correlation of optimum water content, maximum dry density, and strength of requirements through its consistency and compaction test. RESULTS : The lower and upper limit lines are insufficient to secure a relatively strong development and workability compared to an aggregate gradation in the RCCP gradation band region. On the other hand, the line in the RCCP gradation band and the 0.45 power curve in the RCCP gradation band region were satisfactory, ensuring the required strength and workability. CONCLUSIONS : The suitable aggregate gradation on RCCP process should meet the RCCP gradation band area; however, fine particles passing through a #60 sieve do not need to be within the recommended gradation band because the influence of this region on such fine particles is small.