To assess the performance and characteristics of colored building-integrated photovoltaic (BIPV) modules, a comparative assessment of empirical performance was conducted on colored BIPV modules (gray, blue, and orange) and general BIPV module. These modules were installed on the south-facing slope (30°) for comparative assessment through a field test. Monitoring data were collected every 10 min from December 20, 2019 to January 21, 2020 and used to performance and characteristics analysis. Performance ratio and module efficiency were utilized during performance indexing for comparative assessment. For general BIPV modules, the operational efficiency was analyzed at 16.63%, whereas for colored BIPV modules, 13.70% (gray), 15.12 % (blue), and 14.49% (orange) were analyzed. It was discovered that the efficiency reduction caused by transmission losses owing to the application of colored cover glasses were 17.74% (gray), 9.05% (blue), and 9.86 % (orange), under field testing conditions. These values turned on an additional 7% reduction in efficiency for gray BIPV modules, compared to the degradation resulting from transmission drop (gray: 10.87%, blue: 8.99%, and orange: 9.02%) calculated using the efficiency of each module in standard test conditions (STC). Performance ratio analysis resulted in the following values: 0.92 for general BIPV modules, and 0.85 (gray), 0.91 (blue), and 0.91 (orange) for colored BIPV modules. As demonstrated by the above results, modules with a colored cover glass may differ in their operational performance depending on their color, unlike general modules. Therefore, in addition to the performance evaluation under STC, additional factors of degradation require consideration through field test.
The electrical properties of sputtered GDC thin films on $Al_2O_3$ substrates was studied. The electrical properties of the films were measured to evaluate the ion conductivity of GDC thin films for co-planar SOFC electrolytes. The impedance of the GDC thin films on $Al_2O_3$ substrates was affected by the film thickness and the impedance of thin film exhibited higher value than thick films. Similarly, the conductivity of the thick film showed much higher value than thin films. It indicated that the film thickness is the main factor affecting the conductivity and impedance of the GDC electrolyte for the co-planar SOFC.
The laser patterning of sputter-deposited CoNdZr/Cu/CoNbZr multi-layered films had been tried using Nd:YAG laser. However generally it is very difficult to remove metal films because of their high reflectance of the laser on the surfaces. As a counterproposal for this problem authors for the first time tried to deposit energy-absorbing layers on the metal films and then irradiated the laser on the surfaces of energy-absorbing layers. Here the energy-absorbing layers consisted of laser energy-absorbing fine powders and binding polymers. Three kinds of powders for the energy-absorbing layers had been used to see the difference in the pattern formation with the degree of laser energy absorption. They were electrically conductive silver powders insulating BaTiO$_3$powder and semiconducting carbon powder. Remarkable difference in width of the formed pattern and the roughness of pattern edge were observed with the characteristic of the powder for the energy-absorbing layer. The pattern width using carbon paste was about three times larger than that using BaTiO$_3$paste. It was observed that the energy-absorbing layer with carbon was the most effective on this micro-patterning.
Sb doped SnO2(ATO: Antinomy doped Tin Oxide) thin films were prepared by a DC magnetron spttuering method using an oxide target and the electrical characteristics of ATO films were investigated. The experimen-tal conditions are as follows :Ar flow rate ; 0~100 sccm deposition tempera-ture ; 250~40$0^{\circ}C$ DC sputter powder ; 150~550W and sputteing pressure ; 2~7 mTorr, The thickness of depositied ATO films were 600$\AA$~1100 $\AA$ ranges. The resistivity of ATO films was decreased due to the increase of the crystallinity of ATO films with deposition temperature. The decrease of carrier concentration of films with the increase of oxygen flow rate and working pressure is responsible for the increase of resistivity. Increasing of sputtering power raised the resistivity of films by decreasing the carrier mobility.
IGZO thin films were prepared by radio frequency (RF) magnetron sputtering on glass substrates and then annealed in vacuum for 30 minutes at 100, 200 and $300^{\circ}C$, respectively. The thickness of films kept at 100 nm by controlling the deposition rate. While the optical transmittance and sheet resistance of as deposited films were 91.9% and $901{\Omega}/{\Box}$, respectively, the films annealed at $300^{\circ}C$ show the optical transmittance of 95.4% and the sheet resistance of $383{\Omega}/{\Box}$. The experimental results indicate that vacuum-annealed IGZO film at $300^{\circ}C$ is an attractive candidate for the transparent thin film transistor (TTFT) in large area electronic applications.
한국표면공학회 2011년도 춘계학술대회 및 Fine pattern PCB 표면 처리 기술 워크샵
/
pp.117-118
/
2011
초경합금 위에 RF Magnetron Sputter를 이용하여 Ti 중간층을 증착 후 MPECVD(Microwave Plasma Enhanced Chemical Vapor Deposition) 시스템을 이용하여 나노결정 다이아몬드 박막을 증착 하였다. 공정압력, 마이크로웨이브 전력, Ar/$CH_4$ 조성비, 기판온도를 일정하게 놓고 직류 bias의 인가 여부를 변수로 하고 증착시간을 0.5, 1, 2시간으로 변화시켜 박막을 제작하였다. 제작된 시편은 FE-SEM과 AFM을 이용하여 다이아몬드 박막의 표면과 다이아몬드 박막의 표면 거칠기 등을 측정하였고, Raman spectroscopy와 XRD를 이용하여 다이아몬드 결정성을 확인하였다. Automatic Scratch �岵謙�ter를 이용하여 복합박막의 층별 접합력을 측정하였다. 바이어스를 인가하지 않고 다이아몬드 박막을 증착할 경우 증착 시간이 증가할수록 다이아몬드 입자의 평균 크기가 증가하며 입자들이 차지하는 면적이 증가하는 것을 확인하였다. 그러나 1시간이 경과해도 아직 완전한 박막은 형성되지 못하고 2시간 이상 증착 시 완전한 박막을 이루는 것이 확인되었다. 이에 비해서 바이어스 전압을 인가할 경우 1시간 내에 완전한 박막을 이루었다. 표면 거칠기는 바이어스를 인가한 경우가 그렇지 않은 경우에 비해서 조금 높은 것으로 나타났다. 이러한 바이어스 효과는 표면에서의 핵생성 밀도 증가와 재핵생성 속도 증가에 기인하는 것으로 해석된다.
Ta-Ti metal alloy is proposed for alternate gate electrode of ULSI MOS device. Ta-Ti alloy was deposited directly on $SiO_2$ by a co-sputtering method and good interface property was obtained. The sputtering power of each metal target was 100W. Thermal and chemical stability of the electrode was studied by annealing at $500^{\circ}C$ and $600^{\circ}C$ in Ar ambient. X-ray diffraction was measured to study interface reaction and EDX(energy dispersive X-ray) measurement was performed to investigate composition of Ta and Ti element. Electrical properties were evaluated on MOS capacitor, which indicated that the work function of Ta-Ti metal alloy was ${\sim}4.1eV$ compatible with NMOS devices. The measured sheet resistance of alloy was lower than that of poly silicon.
In this study, the microstructure of the CVD-fabricated Cu(In,Ga)Se2 (CIGSe) absorber layer by simulating the stacking sequence used in a co-evaporation method, and changes solar cell performance were investigated. The absorber layer prepared by stacking CuSe and (In,Ga)Se between InSe is separated into Ga-free CuInSe2 and Ga-rich CIGSe, and transformed to CIGSe by selenization heat treatment with slight improvement in the the solar cell efficiency. However, in CVD, since the supply of liquid Cu-Se is not as active as in the co-evaporation method, the nanoocrystalline layer containing a large amount of Ga remained independently in the absorption layer, which acted as a cause of the loss of JSC and FF. Therefore, by using a precursor structure in which CuGa is sputter-deposited on a single layer of InSe deposited by CVD, performance parameters of VOC, JSC, and FF could be greatly improved.
PbxZr0.4Ti0.6O3 thin films were prepared by reactive co-sputtering and annealed by RTA(Rapid Thermal Annealing) process. Effect of Pb content in PbxZr0.4Ti0.6O3 films on the phase transformation was intensively studied. It has been found out that depending on the Pb content as well as RTA temperature, crystal structure of PbxZr0.4Ti0.6O3 films change greatly. It turned out that transformation temperature for perovskite can be lowered and the width of transition temperature region was reduced by increasing Pb content in the film. And the lattice was expanded with increasing Pb content. With increasing RTA temperature, as-deposited phase was transformed into perovskite through three different transformation paths depending on Pb content. It was confirmed that activation energies for nucleation of perovskite structure are much larger than those of its growth.
메그네트론 스퍼터링으로 제작한 고밀도 다층박막($Co_75{{Pt_12}{Cr_13}}$합금) 디스크를 투과전자현미경을 이용해 단면 및 평면의 미세조직의 조사 혹은 미소부위 성분분석을 할 경우, 선행되어야하는 시편준비 경로와 각 단계별 구체적방법 및 그 효과를 연구하였다. Ion밀링시간이 증가함에 따라 시료가 얇게 되는과정에서 스퍼터링된 물질이 관찰될 시편부위의 다른 표면에 증착되므로써 미세조직의 선명도를 해칠 수 있고, 이로인한 해석상의 오류가능성이 시사되었다. 또한, 자기박막 디스크와 같이 다층으로 구성된 단면분석용 시료에서는 서로 맞붙인 실리콘 단결정 접착면을 따라 밀링속도가 선택적으로 커서 우선축이 생김으로써 양질의 시편을 얻기 어려운 문제점이 제기되었다. 이같은 문제를 포함한 전자현미경 시료준비과정에서 생길 수 있는 문제를 해결할 수 있는 실마리와 이를 이용해 수행한 전자현미경 분석결과 및 효과적인 시편준비방법이 본 논문에서 언급되었다.
본 웹사이트에 게시된 이메일 주소가 전자우편 수집 프로그램이나
그 밖의 기술적 장치를 이용하여 무단으로 수집되는 것을 거부하며,
이를 위반시 정보통신망법에 의해 형사 처벌됨을 유념하시기 바랍니다.
[게시일 2004년 10월 1일]
이용약관
제 1 장 총칙
제 1 조 (목적)
이 이용약관은 KoreaScience 홈페이지(이하 “당 사이트”)에서 제공하는 인터넷 서비스(이하 '서비스')의 가입조건 및 이용에 관한 제반 사항과 기타 필요한 사항을 구체적으로 규정함을 목적으로 합니다.
제 2 조 (용어의 정의)
① "이용자"라 함은 당 사이트에 접속하여 이 약관에 따라 당 사이트가 제공하는 서비스를 받는 회원 및 비회원을
말합니다.
② "회원"이라 함은 서비스를 이용하기 위하여 당 사이트에 개인정보를 제공하여 아이디(ID)와 비밀번호를 부여
받은 자를 말합니다.
③ "회원 아이디(ID)"라 함은 회원의 식별 및 서비스 이용을 위하여 자신이 선정한 문자 및 숫자의 조합을
말합니다.
④ "비밀번호(패스워드)"라 함은 회원이 자신의 비밀보호를 위하여 선정한 문자 및 숫자의 조합을 말합니다.
제 3 조 (이용약관의 효력 및 변경)
① 이 약관은 당 사이트에 게시하거나 기타의 방법으로 회원에게 공지함으로써 효력이 발생합니다.
② 당 사이트는 이 약관을 개정할 경우에 적용일자 및 개정사유를 명시하여 현행 약관과 함께 당 사이트의
초기화면에 그 적용일자 7일 이전부터 적용일자 전일까지 공지합니다. 다만, 회원에게 불리하게 약관내용을
변경하는 경우에는 최소한 30일 이상의 사전 유예기간을 두고 공지합니다. 이 경우 당 사이트는 개정 전
내용과 개정 후 내용을 명확하게 비교하여 이용자가 알기 쉽도록 표시합니다.
제 4 조(약관 외 준칙)
① 이 약관은 당 사이트가 제공하는 서비스에 관한 이용안내와 함께 적용됩니다.
② 이 약관에 명시되지 아니한 사항은 관계법령의 규정이 적용됩니다.
제 2 장 이용계약의 체결
제 5 조 (이용계약의 성립 등)
① 이용계약은 이용고객이 당 사이트가 정한 약관에 「동의합니다」를 선택하고, 당 사이트가 정한
온라인신청양식을 작성하여 서비스 이용을 신청한 후, 당 사이트가 이를 승낙함으로써 성립합니다.
② 제1항의 승낙은 당 사이트가 제공하는 과학기술정보검색, 맞춤정보, 서지정보 등 다른 서비스의 이용승낙을
포함합니다.
제 6 조 (회원가입)
서비스를 이용하고자 하는 고객은 당 사이트에서 정한 회원가입양식에 개인정보를 기재하여 가입을 하여야 합니다.
제 7 조 (개인정보의 보호 및 사용)
당 사이트는 관계법령이 정하는 바에 따라 회원 등록정보를 포함한 회원의 개인정보를 보호하기 위해 노력합니다. 회원 개인정보의 보호 및 사용에 대해서는 관련법령 및 당 사이트의 개인정보 보호정책이 적용됩니다.
제 8 조 (이용 신청의 승낙과 제한)
① 당 사이트는 제6조의 규정에 의한 이용신청고객에 대하여 서비스 이용을 승낙합니다.
② 당 사이트는 아래사항에 해당하는 경우에 대해서 승낙하지 아니 합니다.
- 이용계약 신청서의 내용을 허위로 기재한 경우
- 기타 규정한 제반사항을 위반하며 신청하는 경우
제 9 조 (회원 ID 부여 및 변경 등)
① 당 사이트는 이용고객에 대하여 약관에 정하는 바에 따라 자신이 선정한 회원 ID를 부여합니다.
② 회원 ID는 원칙적으로 변경이 불가하며 부득이한 사유로 인하여 변경 하고자 하는 경우에는 해당 ID를
해지하고 재가입해야 합니다.
③ 기타 회원 개인정보 관리 및 변경 등에 관한 사항은 서비스별 안내에 정하는 바에 의합니다.
제 3 장 계약 당사자의 의무
제 10 조 (KISTI의 의무)
① 당 사이트는 이용고객이 희망한 서비스 제공 개시일에 특별한 사정이 없는 한 서비스를 이용할 수 있도록
하여야 합니다.
② 당 사이트는 개인정보 보호를 위해 보안시스템을 구축하며 개인정보 보호정책을 공시하고 준수합니다.
③ 당 사이트는 회원으로부터 제기되는 의견이나 불만이 정당하다고 객관적으로 인정될 경우에는 적절한 절차를
거쳐 즉시 처리하여야 합니다. 다만, 즉시 처리가 곤란한 경우는 회원에게 그 사유와 처리일정을 통보하여야
합니다.
제 11 조 (회원의 의무)
① 이용자는 회원가입 신청 또는 회원정보 변경 시 실명으로 모든 사항을 사실에 근거하여 작성하여야 하며,
허위 또는 타인의 정보를 등록할 경우 일체의 권리를 주장할 수 없습니다.
② 당 사이트가 관계법령 및 개인정보 보호정책에 의거하여 그 책임을 지는 경우를 제외하고 회원에게 부여된
ID의 비밀번호 관리소홀, 부정사용에 의하여 발생하는 모든 결과에 대한 책임은 회원에게 있습니다.
③ 회원은 당 사이트 및 제 3자의 지적 재산권을 침해해서는 안 됩니다.
제 4 장 서비스의 이용
제 12 조 (서비스 이용 시간)
① 서비스 이용은 당 사이트의 업무상 또는 기술상 특별한 지장이 없는 한 연중무휴, 1일 24시간 운영을
원칙으로 합니다. 단, 당 사이트는 시스템 정기점검, 증설 및 교체를 위해 당 사이트가 정한 날이나 시간에
서비스를 일시 중단할 수 있으며, 예정되어 있는 작업으로 인한 서비스 일시중단은 당 사이트 홈페이지를
통해 사전에 공지합니다.
② 당 사이트는 서비스를 특정범위로 분할하여 각 범위별로 이용가능시간을 별도로 지정할 수 있습니다. 다만
이 경우 그 내용을 공지합니다.
제 13 조 (홈페이지 저작권)
① NDSL에서 제공하는 모든 저작물의 저작권은 원저작자에게 있으며, KISTI는 복제/배포/전송권을 확보하고
있습니다.
② NDSL에서 제공하는 콘텐츠를 상업적 및 기타 영리목적으로 복제/배포/전송할 경우 사전에 KISTI의 허락을
받아야 합니다.
③ NDSL에서 제공하는 콘텐츠를 보도, 비평, 교육, 연구 등을 위하여 정당한 범위 안에서 공정한 관행에
합치되게 인용할 수 있습니다.
④ NDSL에서 제공하는 콘텐츠를 무단 복제, 전송, 배포 기타 저작권법에 위반되는 방법으로 이용할 경우
저작권법 제136조에 따라 5년 이하의 징역 또는 5천만 원 이하의 벌금에 처해질 수 있습니다.
제 14 조 (유료서비스)
① 당 사이트 및 협력기관이 정한 유료서비스(원문복사 등)는 별도로 정해진 바에 따르며, 변경사항은 시행 전에
당 사이트 홈페이지를 통하여 회원에게 공지합니다.
② 유료서비스를 이용하려는 회원은 정해진 요금체계에 따라 요금을 납부해야 합니다.
제 5 장 계약 해지 및 이용 제한
제 15 조 (계약 해지)
회원이 이용계약을 해지하고자 하는 때에는 [가입해지] 메뉴를 이용해 직접 해지해야 합니다.
제 16 조 (서비스 이용제한)
① 당 사이트는 회원이 서비스 이용내용에 있어서 본 약관 제 11조 내용을 위반하거나, 다음 각 호에 해당하는
경우 서비스 이용을 제한할 수 있습니다.
- 2년 이상 서비스를 이용한 적이 없는 경우
- 기타 정상적인 서비스 운영에 방해가 될 경우
② 상기 이용제한 규정에 따라 서비스를 이용하는 회원에게 서비스 이용에 대하여 별도 공지 없이 서비스 이용의
일시정지, 이용계약 해지 할 수 있습니다.
제 17 조 (전자우편주소 수집 금지)
회원은 전자우편주소 추출기 등을 이용하여 전자우편주소를 수집 또는 제3자에게 제공할 수 없습니다.
제 6 장 손해배상 및 기타사항
제 18 조 (손해배상)
당 사이트는 무료로 제공되는 서비스와 관련하여 회원에게 어떠한 손해가 발생하더라도 당 사이트가 고의 또는 과실로 인한 손해발생을 제외하고는 이에 대하여 책임을 부담하지 아니합니다.
제 19 조 (관할 법원)
서비스 이용으로 발생한 분쟁에 대해 소송이 제기되는 경우 민사 소송법상의 관할 법원에 제기합니다.
[부 칙]
1. (시행일) 이 약관은 2016년 9월 5일부터 적용되며, 종전 약관은 본 약관으로 대체되며, 개정된 약관의 적용일 이전 가입자도 개정된 약관의 적용을 받습니다.