• Bulletin of the Korean Chemical Society
• /
• 제28권8호
• /
• pp.1396-1400
• /
• 2007

In this study, poly(iso-butyl methacrylate-co-ethylene glycol dimethacrylate) [poly(iso-BMA-co-EGDMA)] microgel was prepared and used as a face powder additive. The spreading, adhesiveness, and skin reactivity of poly(iso-BMA-co-EGDMA) microgel-containing face powder II were investigated and compared with the same properties of commercially available Silica bead 700-containing face powder I. In the results, the particle size of the poly(iso-BMA-co-EGDMA) microgel was significantly swelled as a result of sebum absorption. Face powder II showed a lower primary irritation index and a higher adhesiveness than did face powder I. Face powder I showed a low sebum absorption ratio and a relatively high rate of sebum absorption, whereas face powder II, contrastingly, exhibited a high sebum absorption ratio and a low rate of sebum absorption, which properties would reduce the phenomena of facial strain and sliminess. These results indicate that poly(iso- BMA-co-EGDMA) microgel has outstanding sebum absorption characteristic and adhesiveness, and thus that it is a good candidate for use as a face powder additive.

• Applied Biological Chemistry
• /
• 제42권3호
• /
• pp.218-222
• /
• 1999

자당지방산에스테르(SE), 이소말토올리고당(IO) 또는 글리세린(GL)을 첨가한 백설기를 7일간 저장한 후 저장온도, 수분함량 및 첨가물의 농도에 따른 백설기의 텍스쳐에 미치는 영향을 경도, 응집성 및 씹힘성의 관점에서 반응표면 분석법으로 비교분석하였다. SE첨가 백설기 경도는 20, 50 및 $80^{\circ}C$의 저장온도에서 등고선 값은 각각 $1500{\sim}3200,\;500{\sim}1300$ 및 $100{\sim}400\;g_f$로 저장온도가 올라감에 따라서 급격히 감소하였다. $20^{\circ}C$ 및 $50^{\circ}C$의 저장에서는 수분함량과 SE농도 증가에 따라서 경도는 감소하였으나 $80^{\circ}C$의 고온저장에서는 수분함량 증가나 SE첨가효과가 거의 나타나지 않았다. IO나 GL첨가 백설기의 경도는 일반적으로 저장온도가 높아질수록 수분함량 및 첨가물 농도가 증가할수록 감소를 나타내었다. 백설기의 경도에 미치는 영향은 저장온도, 수분함량, 첨가물농도 순이었으며 저장온도 조절이 백설기의 저장성 향상에 가장 효과적이라는 것을 의미한다. 응집성 측면에서 SE 또는 GL첨가 백설기는 저장온도가 $20^{\circ}C$에서 $50^{\circ}C$로 높아짐에 따라서 응집성 증가를 보였으나 $50^{\circ}C$와 $80^{\circ}C$의 저장온도간에는 차이가 거의 없었다. 또한, 수분함량이 40%부근에서 높은 응집성을 나타내었으며 GL첨가 백설기는 농도가 0.5%부근에서 낮은 값을 보였다. 저장온도, 첨가물 농도 및 수분함량 순으로 백설기의 응집성에 영향을 미쳤다. 씹힘성은 첨가물의 종류에 관계없이 저장온도가 높아질수록, 수분함량과 첨가물 농도가 증가할수록 감소하였다. 씹힘성에 영향을 미치는 정도는 저장온도, 수분함량, 첨가물 농도 순이었다.

• 한국해양공학회지
• /
• 제21권3호
• /
• pp.65-70
• /
• 2007

There are many kinds of protection methods for marine structures, with varyingeconomical and environmental advantages. The coating protection method is being widely used in both continental and marine structures. In this study, by adding some additives, such as Zn powder(Zn), carbon black(CB) to epoxy anti-corrosive paint, the effect on the corrosion resistance was investigated throughan electrochemical method. The additive of Zn(20)+CB(10) showed the lowest passivity current density. Polarization resistance in both cyclic voltammogram and impedance measurement of an additive of Zn(20)+CB(10) was also the largest value, compared to other additives. Furthermore, rusting and bubbling was not observed on the surface of the test specimen with the additive of Zn(20)+CB(10), compared to other specimens. It is suggested that the corrosion resistance of the anti-corrosive paint can be improved by using some additives.

• 한국해양공학회:학술대회논문집
• /
• 한국해양공학회 2006년 창립20주년기념 정기학술대회 및 국제워크샵
• /
• pp.173-176
• /
• 2006

There are many kinds of protection methods for marine structures by using and environmental condition. Coating protection method, one of these methods is being widely adopted to both all ground and marine structures. In this study, by adding some additives such as Zn powder(Zn), carbon black(CB) to epoxy anti-corrosive paint, the effect to promote corrosion resistance was investigated with electrochemical method. Corrosion potentials with additives shifted to negative direction than no additive. However passivity current density increased than no additive except for Zn(20)+CB(10), especially, additive of Zn(20)+CB(10) showed the smallest passivity current density. Polarization resistance of Zn(20)+CB(10) by both cyclic voltammogram and impedance measurement was the largest value than other additives. And also surface phenomenon by adding Zn(20)+CB(10) was observed a good add condition not showing bubbling than other additives.

• 한국재료학회지
• /
• 제31권12호
• /
• pp.710-718
• /
• 2021

Recently, due to high theoretical capacitance and excellent ion diffusion rate caused by the 2D layered crystal structure, transition metal hydroxides (TMHs) have generated considerable attention as active materials in supercapacitors (or electrochemical capacitors). However, TMHs should be designed using morphological or structural modification if they are to be used as active materials in supercapacitors, because they have insulation properties that induce low charge transfer rate. This study aims to modify the morphological structure for high cycling stability and fast charge storage kinetics of TMHs through the use of nickel cobalt hydroxide [NiCo(OH)₂] decorated on nickel foam. Among the samples used, needle-like NiCo(OH)₂ decorated on nickel foam offers a high specific capacitance (1110.9 F/g at current density of 0.5 A/g) with good rate capability (1110.9 - 746.7 F/g at current densities of 0.5 - 10.0 A/g). Moreover, at a high current density (10.0 A/g), a remarkable capacitance (713.8 F/g) and capacitance retention of 95.6% after 5000 cycles are noted. These results are attributed to high charge storage sites of needle-like NiCo(OH)₂ and uniformly grown NiCo(OH)₂ on nickel foam surface.

• 펄프종이기술
• /
• 제48권1호
• /
• pp.134-141
• /
• 2016

Dampening in printing is not only used with plain water but also used with various substances like dampening additive, in order to improve the wetting property by lowering the surface tension and to control material for modifing the ink transfer characteristic with proper emulsification. We have studied the printing quality according to these, looking into interrelationship among the dampening solution's pH, electrical conductivity and IPA content, prescribing the proper usage and minimum usage of fountain solution and dampening additive. In this study, it shows good result when mixing at the 7 wt% dampening with additive solution, which is result from the color density of printed sheets in accordance with the change of dampening solution condition. And the printed density value calculated 1 hour after printing, it shows relatively safe value at the etch liquid 4 wt% and IPA addition 2 wt%. The dry down at this test showed similar results regardless of various dampening conditions on coated paper, but in case of uncoated paper, the dry down showed a quite gap of different due to the fast penetration to the paper.

• Transactions on Electrical and Electronic Materials
• /
• 제18권6호
• /
• pp.334-337
• /
• 2017

In this paper, to develop the ceramics with high $d_{33}$ and high $Q_m$ for ultrasonic transducer applications, $0.10Pb(Ni_{1/3}Nb_{2/3})O_3-0.07Pb(Mn_{1/3}Nb_{2/3})O_3-0.83Pb(Zr_{0.5}Ti_{0.5})_{0.83}O_3$ (PNN-PMN-PZT) ceramics were sintered at $940^{\circ}C$ using $CuO-Li_2CO_3-Bi_2O_3$ (CLBO) as a sintering aid by a traditional solid-state technique. The influence of zinc oxide additive on the physical properties of the prepared ceramics were systematically investigated. The R-T (rhombohedral-tetragonal) phase coexistence was found in the ceramics without zinc oxide additive and with increasing amounts of ZnO additive, the specimens showed a tetragonal phase. The formation of a liquid phase between ZnO and $Bi_2O_3$ contributed significantly to the grain growth of specimens. For the 0.1 wt% ZnO ceramics, the optimal physical properties of $d_{33}=370pC/N$, ${\varepsilon}_r=1,344$, $k_p=0.621$, and $Q_m=1,523$ were obtained.

• 동력기계공학회지
• /
• 제6권2호
• /
• pp.18-23
• /
• 2002

Recently, as people pay attention to the environmental pollution, the emission of diesel engine has become a serious problem. Diesel Oxidation Catalysts(DOC) were experimentally investigated for the purification of pollutants exhaust emission from the diesel engine. In this study, the conversion efficiency of exhaust gas was investigated with various washcoat materials of the DOC. It was formed that CO conversion efficiency depended on temperature, but THC conversion was dominated by temperature and space velocity. Conversion efficiency of THC and CO increased with the addition of ZSM-5 in the washcoat, whereas these conversion efficiency decreased by adding Nd and Ba additives. $V_2O_5$ additive had the thermal stability for high temperature. Thermal durability of the catalyst was improved as increase of $V_2O_5$ additive.

• 한국분말재료학회지
• /
• 제26권4호
• /
• pp.319-326
• /
• 2019

Additive manufacturing (AM) is a highly innovative method for joining dissimilar materials for industrial applications. In the present work, AM of STS630 and Ti-6Al-4V powder alloys on medium entropy alloys (MEAs) NiCrCo and NiCrCoMn is studied. The STS630 and Ti64 powders are deposited on the MEAs. Joint delamination and cracks are observed after the deposition of Ti64 on the MEAs, whereas the deposition of STS630 on the MEAs is successful, without any cracks and joint delamination. The microstructure around the fusion zone interface is characterized by scanning electron microscopy and X-ray diffraction. Intermetallic compounds are formed at the interfacial regions of MEA-Ti64 samples. In addition, Vicker's hardness value increased dramatically at the joint interface between MEAs and Ti-6Al-4V compared to that between MEAs and STS630. This result is attributed to the brittle nature of the joint, which can lead to a decrease in the joint strength.

• Bulletin of the Korean Chemical Society
• /
• 제34권3호
• /
• pp.927-930
• /
• 2013

We developed an electroplating process of cobalt nanowires of which line-widths were between 70 and 200 nm. The plating electrolyte was made of $CoSO_4$ and an organic additive, dimethyldithiocarbamic acid ester sodium salt (DAESA). DAESA in plating electrolytes had an accelerating effect and reduced the surface roughness of plated cobalt thin films. We obtained void-free cobalt nanowires when the plating current density was 6.25 mA/$cm^2$ and DAESA concentration was 1 mL/L.