• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.60 no.2
• /
• pp.451-454
• /
• 2011

In this paper, a wideband clock generator using novel Automatic frequency calibration(AFC) scheme is proposed. Wideband clock generator using AFC has the advantage of small VCO gain and wide frequency band. The conventional AFC compares whether the feedback frequency is faster or slower then the reference frequency. However, the proposed AFC can detect frequency difference between reference frequency with feedback frequency. So it can be reduced an operation time than conventional methods AFC. Conventional AFC goes to the initial code if the frequency step changed. This AFC, on the other hand, can a prior state code so it can approach a fast operation. In simulation results, the proposed clock generator is designed for DisplayPort using the CMOS ring-VCO. The VCO tuning range is 350MHz, and a VCO frequency is 270MHz. The lock time of clock generator is less then 3us at input reference frequency, 67.5MHz. The phase noise is -109dBC/Hz at 1MHz offset from the center frequency. and power consumption is 10.1mW at 1.8V supply and layout area is $0.384mm^2$.

• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2004.05b
• /
• pp.583-586
• /
• 2004

In this paper, we have analyzed the performance of synchronization of CCK(Complementary Code Keying) modulation scheme used for IEEE 802.11g wireless LAM system supporting 54 Mbps of high speed data rate over 2.4 GHz. At receiver, the clock frequency offset is caused by noise or fading. This frequency error occurs the offset of clock timing and causes ISI. Therefore the tracking is required to reduce the clock timing offset. The DLL(Delay Lock Loop), asychronization mode, performing tacking the clock is used for the simulation. The simulation result shows jitter variance and BER performance in the AWGN and multipath fading channel environment.

• ETRI Journal
• /
• v.45 no.1
• /
• pp.150-162
• /
• 2023

The polar delta-sigma modulator (DSM) transmitter architecture exhibits good coding efficiency and can be used for software-defined radio applications. However, the necessity of high clock speed is one of the major drawbacks of using this transmitter architecture. This study proposes a low-complexity timeinterleaved architecture for the polar DSM transmitter baseband part to reduce the clock speed requirement of the polar DSM transmitter using an upsampling technique. Simulations show that using the proposed four-branch timeinterleaved polar DSM transmitter baseband part, the clock speed requirement of the transmitter is reduced by four times without degrading the signal-tonoise-and-distortion ratio.

• Journal of Digital Contents Society
• /
• v.6 no.1
• /
• pp.41-48
• /
• 2005

In this paper, we propose and evaluate symbol timing recovery algorithm for S-DMT cable modern, which supports more channels and better quality symmetric mutimedia service over HFC network. We adopt timing recovery algorithm of PN sequence insertion in time domain and evaluate the performance of it in various noise channel such as AWGN, ISI, impulse. We verified that performance of this algorithm is depends on the channel noise environment and sampling clock offset and that over 10 dB degradation of Eb/No is occurred at the timing failure probability of $10^3$ in the composite noise channel of AWGN, ISI, and impulse in comparison with impulse noise-alone channel. finally, we verified that this algorithm showed good timing failure probability in case of sampling clock optimization was performed in advance.

• Journal of the Korean Institute of Telematics and Electronics C
• /
• v.36C no.11
• /
• pp.10-17
• /
• 1999

In this paper, CMOS IADC(Current-mode Analog-to-Digital Converter) which consists of only CMOS transistors is proposed. Each stages is made up 1.5-bit bit cells composed of CSH(Current-mode Sample-and-Hold) and CCMP(Current Comparator). The differential CSH which designed to eliminate CFT(Clock Feedthrough), to meet at least 9-bit resolution, is placed at the front-end of each bit cells, and each stages of bit cell ADSC (Analog-to-Digital Subconverter) is made up two latch CCMPs. With the HYUNDAI TEX>$0.65\mu\textrm{m}$ CMOS parameter, the ACAD simulation results show that the proposed IADC can be operated with 47 dB of SINAD(Signal to Noise- Plus-Distortion), 50dB(8-bit) of SNR(Signal-to-Noise) and 37.7 mW of power consumption for input signal of 100 KHz at 20 Ms/s.

• Journal of the Institute of Electronics Engineers of Korea TC
• /
• v.42 no.5 s.335
• /
• pp.13-22
• /
• 2005

IEEE 802.11a is a standard for the high-speed wireless local area network (WLAN), supporting from 6 up to 54 Mbps in a 5 GHz band. We propose a channel equalization algerian and a sampling clock recovery algorithm by utilizing the Viterbi decoder output of the IEEE 802.11a WLAN standard. The proposed channel equalizer adaptively compensates channel variations. The proposed system uses re-encoded Viterbi decoder outputs as reference symbols for the adaptation of the channel equalizer. It also extracts sampling phase information with the Viterbi decoder outputs for fine adjustment of the sampling clock. The proposed sampling clock recovery and equalizer are more robust to noise and frequency selective fading environments than conventional systems using only four pilot samples.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.8 no.2
• /
• pp.245-249
• /
• 2004

In this paper, we have proposed a clock recovery algorithm of Orthogonal Frequency Division Multiplexing/Quadrature Phase Shift Keying Modulation-Digital Microwave Radio(OFDM/QPSK-DMR) system using Band Limited-Pulse Shaping Filter(BL-PSF) and compared the clock phase error variance of OFDM/QPSK-DMR system with that of single carrier DMR system. The OFDM/QPSK-DMR system using windowing method requires training sequence or Cyclic Prefix (CP) to synchronize the clock phase of received signal. But transmit efficient is increased in our proposed DMR system because of no using redundant data such as training sequence or CP. The proposed clock recovery algorithm is simply realized in the OFDM/QPSK-DMR system using BL-PSF. The simulation results confirm that the proposed clock recovery algorithm has the same clock phase error variance performance in a single carrier DR system under Additive White Gaussian Noise(AWGN) environment.

• The KIPS Transactions:PartC
• /
• v.13C no.3 s.106
• /
• pp.303-310
• /
• 2006

This paper is to execute a study for characteristic analysis of synchronization clock and maximum network node number with various clock states, normal, SPT, LPT, in NG-SDH networks. Through the simulations, maximum network node numbers showed from 42 to 38 nodes in normal state. In SPT state, maximum network node numbers, when the last NE network applied to only SPT state, presented from 19 to 4 nodes, much less than normal state. Node numbers to meet specification in case of occurrence of SPT state in all NE networks decreased greatly. In LPT state, all maximum node numbers, when the last NE network applied to only LPT state, presented more than 50 nodes, and the results in case of occurrence of LPT state in all NE networks were also identified. However, node numbers to meet specification in case of LPT state in all DOTS networks were few large with difference between LPT and normal or SPT state.

• Journal of the Korean Institute of Telematics and Electronics B
• /
• v.30B no.12
• /
• pp.31-39
• /
• 1993

In the playback signal processing of a digital magnetic recording system, the major signal processing processes consist of pulse equalization. pulse detection, clock recovery, and data recovery. Equalizer which compensates interference occurrde between pulses recorded in high density on a magnetic media is realized by pulse slimming method, and pulse detection by a integrating detector. Clock recovery from the detector output was accomplished by using PLL. and data recovery to reduce noise effects was carried out by utilizing the three sampling clocks recovered in clock recovery process. In this paper these processes are implemented in hardware and its performance is evaluated by experimenting with a commercial DAT. It was found that the playback signal processor proposed is suitable to the practical high density magnetic recording system.

• Journal of the Korean Institute of Telematics and Electronics
• /
• v.26 no.10
• /
• pp.1606-1616
• /
• 1989

In this paper, the design of DYNAMIC CMOS ARRAY LOGIC which has both advantages of dynamic CMOS and array logic circuits is proposed. The major components of DYNAMIC CMOS ARRAY LOGIC are two-stage dunamic CMOS circuits and an internal clock generator. The function block of dynamic CMOS circuits is realized as a parallel interconnection of NMOS transistors. Therefore the operating speed of DYNAMIC CMOS ARRAY LOGIC is much faster than the one of the conventional dynamic CMOS PLAs and static CMOS PLA. Also, the charge redistribution problem by internl delay is solved. The internal clock generator generates four internal clocks that drive all the dynamic CMOS circuits. During evaluation, two clocks of them are delayed as compared with others. Therefore the race problem is completoly eliminated. The internal clock generator also prevents the reduction of circuit output voltage and noise margin due to leakage current and charge coupling without any penalty in circuit operating speed or chip area utilization.