• 한국수소및신에너지학회논문집
• /
• 제10권1호
• /
• pp.9-17
• /
• 1999

기계적인 합금처리된 여러 Mg-Ni 혼합물 중에서 가장 우수한 수소저장 성질을 가지고 있는 Mg-25wt.%Ni 혼합물의 수소화물 형성 및 분해 반응에 대한 반응속도론적 연구를 하였다. 수소화물 형성 및 분해 속도를 측정하여 이론적인 반응 속도식과 비교함으로써 율속 단계를 결정하였다. Mg-25wt.%Ni의 수소화물 형성의 율속단계는 $H_a$ = 4.0 미만의 여러 $H_a$ 범위에서는 입자간 통로 (interparticle channel), 입자의 갈라진 틈(crack) 등을 통한 수소 분자의 이동 단계인 Knudsen 유동과 보통의 기체 확산이고, 4.0 < $H_a{\leq}4.25$ 범위에서는 성장하는 수소화물 층을 통한 수소 원자의 확산으로 생각된다. Mg-25wt.%Ni의 수소화물 분해의 율속 단계는 전 $H_d$ 범위에 걸쳐 수소 분자의 이동 단계인 Knusden 유동과 보통의 기체 확산이다.

• Biotechnology and Bioprocess Engineering:BBE
• /
• 제10권4호
• /
• pp.309-314
• /
• 2005

We performed a basic experiment for the rapid, on-line, real-time measurement of hepatitis B surface antigen using a surface plasmon resonance biosensor. We immobilized anti­HBsAg (hepatitis B surface antigen) polyclonal antibody, as a ligand, to the dextran layer on a CM5 chip surface that had previously been activated by N-hydroxysuccinimide. A sample solution containing HBsAg was fed through a microfluidic channel, and the reflecting angle change due to the mass increase from the binding was detected. The binding characteristics between HBsAg and its polyclonal antibody followed the typical monolayer adsorption isotherm. When the entire immobilized antibody had interacted, no additional, non-specific binding occurred, suggesting the immunoreaction was very specific. The bound antigen per unit mass of the antibody was independent of the immobilized ligand density. No significant steric hindrance was observed at an immobilization density of approximately $17.6 ng/mm^2$. The relationship between the HBsAg concentration in the sample solution and the antigen bound to the ligand was linear up to ca. $40{\mu}g$/mL. This linearity was much higher than that of the ELISA method. It appeared the anti­gen-antibody binding increased as the immobilized ligand density increased. In summary, this study showed the potential of this SPR biosensor-based method as a rapid, simple and multi­sample on-line assay. Once properly validated, it may serve as a more efficient method for HBsAg quantification for replacing the ELISA.

• Applied Microscopy
• /
• 제30권3호
• /
• pp.311-319
• /
• 2000

대하 아가미의 형태와 미세구조를 광학현미경과 전자현미경으로 조사하였다. 대하는 수지형 아가미를 가진 다. 아가미는 출새관과 입새관을 구분하는 세로 격벽을 가진다. 각각의 새판은 전자밀도가 다른 다층구조의 큐터클로 싸여 있다. 새판 기저세포들은 편평형이며, 전자밀도가 높은 세포질을 가진다. 상피세포층은 단층으로 큰 핵을 가진 편평상피로 구성된다. 새판의 기둥구조는 세로방향의 미세소관들과 측면 membrane interdigitation을 가진다. AB-PAS음성 분비세포들은 다세포선의 형태이다. 활성화된 선에서 각 세포의 경계부는 뚜렷하지 않으며, 세포질에는 활면소포체, 미토콘드리아, 전자밀도가 낮으며 막을 가진 분비소포들과 granular rosettes를 가진다. 비 활성화된 선에서는 세포 경계가 뚜렷하며, 세포질에서는 전자밀도가 높은 다수의 작은 과립들이 산재한다. 그리고 alcian blue에 양성인 단세포 분비세포들은 세포질에 발달된 다수의 골지체와 조면소포체들을 함유한다.

• 멤브레인
• /
• 제20권1호
• /
• pp.69-75
• /
• 2010

수소투과금속인 tantalum과 세라믹 지지체로 $Y_2O_3$-stabilized $ZrO_2$ (YSZ)를 이용하여 cermet 수소분리막을 제조하였다. Ta/YSZ cermet 분리막은 헬륨분위기에서의 예비소결과 고진공 하에서의 본소결을 통해 제조하였으며, 소결 및 밀봉 과정에서 발생하는 불순물은 연마를 통해 제거 가능하였다. 이렇게 제조된 분리막은 tantalum의 연속상이 잘 발달된 치밀구조를 보였다. 수소 해리를 위해 팔라듐 코팅을 한 Ta/YSZ 분리막을 이용하여 $200{\sim}350^{\circ}C$의 범위에서 수소투과실험을 수행하였다. $300^{\circ}C$에서 분리막에 균열이 형성되었고 Pd 코팅층은 몇 곳이 박리되었다. XRD 결과는 tantalum이 수소와 반응하여 $Ta_2H$가 생성되는 것을 보여주며, $Ta_2H$에 인한 격자 팽창이 분리막의 결함을 초래하였다.

• 조명전기설비학회논문지
• /
• 제16권5호
• /
• pp.66-74
• /
• 2002

OFDM(Orthogonal Frequency Division Multiplexing)변조방식은 데이터를 다수의 반송파를 이용해서 주파수상 에서 분산해서 전송하는 디지털변조방식의 일종으로, 멀티패스 간섭에 강한 이점 등으로 인해 디지털음성방송이나 지상파 디지털TV방송 등에 적용되고 있으며, 1997년부터는 5［㎓］대역의 구내용 초고속무선LAN설비로서 IEEE 802.11 TG(task group)a에서 규격작업이 이뤄짐에 따라, 관련된 연구들이 활발하게 진행되어지고 있다. OFDM방식의 초고속무선LAN설비를 구현하기 위한 송수신부의 핵심소자로서는 IEFT 및 FFT모듈이 있다. 본 논문은 IFFT및 FFT모듈을 행렬 원소의 라운딩기법을 기반으로 한 전류모드회로를 이용해서 설계 및 구현함으로써 저소비전력화와 고속처리동작이 가능하도록 하였다. 또한 제안한 IFFT 및 FFT모듈을 IEEE 802.11a규격에 근거한 송수신부 모뎀에 적용한 경우에 대한 BER특성을 모의실험을 통해 확인함으로써, 제안한 IFFT 및 FFT모듈을 이용한 송수신 시스템 설비가 AWGN채널 환경에서 유용하게 동작함을 입증하였다.

• 한국해양공학회지
• /
• 제26권4호
• /
• pp.37-41
• /
• 2012

Due to global warming, the need to secure alternative resources has become more important nationally. Because of the very strong current on the west coast, with a tidal range of up to 10 m, there are many suitable sites for the application of TCP (tidal current power) in Korea. In the southwest region, a strong current is created in the narrow channels between the numerous islands. A rotor is an essential component that can convert tidal current energy into rotational energy to generate electricity. The design optimization of a rotor is very important to maximize the power production. The performance of a rotor can be determined using various parameters, including the number of blades, shape, sectional size, diameter, etc. There are many offshore jetties and piers with high current velocities. Thus, a VAT (vertical axis turbine) system, which can generate power regardless of flow direction changes, could be effectively applied to cylindrical structures. A VAT system could give an advantage to a caisson-type breakwater because it allows water to circulate well. This paper introduces a multi-layer vertical axis tidal current power system. A Savonius turbine was designed, and a performance analysis was carried out using CFD. A physical model was also demonstrated in CWC, and the results are compared with CFD.

• 한국지구과학회지
• /
• 제26권2호
• /
• pp.149-159
• /
• 2005

Simultaneous observations of MODIS (Moderate-resolution Imaging Spectroradiometer) onboard the Aqua and Terra satellites and weather station at ground near the Inchon International Airport (37.2-37.7 N, 125.7-127.2 E) during the period from December 2002 to September 2004 have been utilized in order to analyze the characteristics of satellite-observed infrared (IR) and visible data under fog and clear-sky conditions, respectively. The differences $(T_{3.7-11})$ in brightness temperature between $3.75{\mu}m\;and\;11.0{\mu}m$ were used as threshold values for remote-sensing fog (or low clouds) from satellite during day and night. The $T_{3.7-11}$ value during daytime was greater by about 21 K when it was foggy than that when it was clear, but during nighttime fog it was less by 1.5 K than during nighttime clear-sky. The value was changed due to different values of emission of fog particles at the wavelength. Since the near-IR channel at $3.7{\mu}m$ was affected by solar and IR radiations in the daytime, both IR and visible channels (or reflectance) have been used to detect fog. The reflectance during fog was higher by 0.05-0.6 than that during clear-sky, and varied seasonally. In this study, the threshold values included uncertainties when clouds existed above a layer of fog.

• Transactions on Electrical and Electronic Materials
• /
• 제15권6호
• /
• pp.328-332
• /
• 2014

Thin film transistors (TFTs) with an amorphous silicon zinc tin oxide (a-2SZTO) channel layer have been fabricated using an RF magnetron sputtering system. The effect of the change of excitation electron on the variation of the total interfacial trap states of a-2SZTO systems was investigated depending on sputtering power, since the interfacial state could be changed by changing sputtering power. It is well known that Si can effectively reduce the generation of the oxygen vacancies. However, The a-2SZTO systems of ZTO doped with 2 wt% Si could be degraded because the Si peripheral electron belonging to a p-orbital affects the amorphous zinc tin oxide (a-ZTO) TFTs of the s-orbital overlap structure. We fabricated amorphous 2 wt% Si-doped ZnSnO (a-2SZTO) TFTs using an RF magnetron sputtering system. The a-2SZTO TFTs show an improvement of the electrical property with increasing power. The a-2SZTO TFTs fabricated at a power of 30 W showed many of the total interfacial trap states. The a-2SZTO TFTs at a power of 30 W showed poor electrical property. However, at 50 W power, the total interfacial trap states showed improvement. In addition, the improved total interfacial states affected the thermal stress of a-2SZTO TFTs. Therefore, a-2SZTO TFTs fabricated at 50 W power showed a relatively small shift of threshold voltage. Similarly, the activation energy of a-2SZTO TFTs fabricated at 50 W power exhibits a relatively large falling rate (0.0475 eV/V) with a relatively high activation energy, which means that the a-2SZTO TFTs fabricated at 50 W power has a relatively lower trap density than other power cases. As a result, the electrical characteristics of a-2SZTO TFTs fabricated at a sputtering power of 50 W are enhanced. The TFTs fabricated by rf sputter should be carefully optimized to provide better stability for a-2SZTO in terms of the sputtering power, which is closely related to the interfacial trap states.

• 한국신재생에너지학회:학술대회논문집
• /
• 한국신재생에너지학회 2011년도 춘계학술대회 초록집
• /
• pp.116.1-116.1
• /
• 2011

Materials with a combination of high electrical conductivity and optical transparency are important components of many electronic and optoelectronic devices such as liquid crystal displays, solar cells, and light emitting diodes. In this study, to fabricate a low-resistance and high optical transparent electrode film for organic photovoltaic, the following steps were performed: the design and manufacture of an electroforming stamp mold, the fabrication of thermal roll imprinted (TRI) poly-carbonate (PC) patterned films, the manufacture of high-conductivity and low-resistance Ag paste which was filled into patterned PC film using a doctor blade process and then coated with a thin film layer of conductive polymer by a spin coating process. As a result of these imprinting processes the PC films obtained a line width of $10{\pm}0.5{\mu}m$, a channel length of $500{\pm}2{\mu}m$, and a pattern depth of $7.34{\pm}0.5{\mu}m$. After the Ag paste was used to fill part of the patterned film with conductive polymer coating, the following parameters were obtained: a sheet resistance of $9.65{\Omega}$/sq, optical transparency values were 83.69 % at a wavelength of 550 nm.

• 한국신재생에너지학회:학술대회논문집
• /
• 한국신재생에너지학회 2007년도 춘계학술대회
• /
• pp.101-104
• /
• 2007

금속 분리판으로 제작된 연료전지 스택의 기계적인 거동을 유한요소 해석을 통하여 살펴보았다. 연료전지의 구성요소는 크게 금속 분리판, 가스켓, MEA, GDL, 엔드 플레이트로 나눌 수 있다. 각각의 요소들은 적절한 힘에 의하여 체결되어야 하고 이에 의해 연료전지 스택의 성능이 많아 좌우된다. 유한 요소해석을 위해 가스켓, GDL을 금속 분리판 위에서 변위에 따른 힘의 변화를 실험을 통해 구했으며, 금속 분리판의 유로 부분을 단순 평판으로 치환하여 유한 요소해석을 진행하였고, 해석 결과와 실험결과가 일치함을 확인하였다. 이를 통해 금속 분리판 스택이 체결되었을 때의 기계적 거동을 유추할 수 있다.