• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2004년도 춘계학술대회 논문집 방전 플라즈마 유기절연재료 초전도 자성체연구회
• /
• pp.173-176
• /
• 2004

The piezoelectric ceramics for AE sensor piezoelectric devices are desirable to possess higher resonance vibrations. The compositions of $0.9Pb(Zr_xTi_{1-x})O_3-0.1Pb(Mn_{1/3}Nb_{1/3}Sb_{1/3})O_3$ (PZT-PMNS) in this work are selected for obtaining especially large electromechanical coupling factor, high mechanical quality factor and high Curie temperature. This ceramic has higher piezoelectric activity and higher electromechanical coupling factor, but the ceramic has lower Curie temperature. The piezoelectric and dielectric characteristics of PZT-PMNS ternary system are investigated as functions of $Ti^{2+}$, $Zi^{2+}$ mol rate. As the results, MPB(morphotropic phase boundary) in this piezoelectric ceramic is x=0.522. Resonance vibrations of PZT ceramics are investigated as ball-bearing drop test. For the use of AE sensor that driving with pre-amplifier, filter circuit after packed this ceramic and an elastic body.

• 한국세라믹학회지
• /
• 제32권12호
• /
• pp.1369-1376
• /
• 1995

The WO3 thin-film NOx sensor which is of practical use and includes the heater and the temperature sensor was fabricated. The WO3 thin films as a gas-sensing layer was deposited at ambient temperature in a high-vacuum resistance heated evaporator. The highest sensitivity of the WO3 thin-film sensor to NOx was obtained under the condition of the annealing temperature of 50$0^{\circ}C$ and the operating temperature of 30$0^{\circ}C$. The gas sensing characteristics of this sensor was excellent, i.e. high sensitivity (Rgas/Rair in 3 ppm NO2=53) and fast response time (4 seconds).

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 1997년도 춘계학술대회논문집; 경주코오롱호텔; 22-23 May 1997
• /
• pp.434-439
• /
• 1997

This paper presents the active control of a flexible plate vibration. The plate was excited by white noise point force and the control was performed by one or two piezo ceramic actuator bonded to the surface of the plate. An adaptive controller based on filtered-x or multiple filtered-x LMS algorithm was used and the controller was defined by minimizing the square of the response of error sensor. In the experiment, PZT sensor was used as an error sensor while white noise was applied as a disturbance. In the case of multiple channel control, more than 22 dB of vibration reduction was achieved. Results indicate that the vibration of a flexible plate could be controlled effectively when the piezo ceramic actuator was used with multiple filtered-x LMS algorithm.

• 센서학회지
• /
• 제18권5호
• /
• pp.343-348
• /
• 2009

$NiO{\cdot}(Co_{0.25}Mn_{0.75})_2O_3$(Mn-Ni-Co) and $Ba_{0.5}Sr_{0.5}TiO_3$(BST) thick films were screen printed on Pt patterned alumina substrate to investigate the effects of sintering temperature on humidity and temperature sensing properties of ceramic sensors. A raise in sintering temperature increased resistance and B constant of the Mn-Ni-Co temperature sensor. This may have derived from the synergic effects of the reduction in charge carriers caused by the substitution of Co for Mn as well as the formation of microcracks from the difference in thermal expansion coefficients. Dependence of resistance on humidity of the Mn-Ni-Co temperature sensor, however, was not found. BST films sintered at temperatures in the range of $1100^{\circ}C$ to $1150^{\circ}C$ showed excellent humidity sensing properties. The BST humidity sensor was faster in its response than the Mn-Ni-Co temperature sensor. The humidity sensor, however, proved to be unstable under various temperatures, suggesting a need for a temperature stabilizing device. In contrast, the Mn-Ni-Co temperature sensor was stable under humid conditions.

• 한국결정성장학회지
• /
• 제20권5호
• /
• pp.221-226
• /
• 2010

메칠멜캅탄($CH_3SH$) 가스를 검출하는 수정진동자(QCM) 가스센서를 QCM의 전극에 $TiO_2$ 나노입자와 전해질 폴리머를 증착하여 제조하였다. LBL-SA법에 의해 제조된 $TiO_2$/PSS 박막은 높은 비표면적을 나타내었고, 가스센서의 감도를 증가시켰다. 1.0 ppm의 농도를 갖는 메칠멜캅탄에 노출된 TEA 혹은 $TiO_2$/PSS 막이 증착된 QCM의 주파수 변이는 각각 약 9 Hz, 2 Hz 였다. ($TiO_2$/PSS) 박막의 증착수가 늘어남에 따라 제조된 박막의 비표면적이 증가하게 되어 QCM 센서의 주파수 변이도 점차적으로 증가하였다. 추가적으로 메칠멜캅탄 가스의 농도가 0.5 ppm에서 2.0 ppm으로 높아짐에 따라 QCM 센서의 주파수 변화도 증가되었다. 본 연구에서는, ($TiO_2$/PSS) 박막이 증착된 QCM 센서의 표면구조의 변화와 센서 특성을 측정하였다.

• 센서학회지
• /
• 제23권6호
• /
• pp.420-424
• /
• 2014

Aluminum-scandium nitride ($Al_{1-x}Sc_xN$) thin films with a TiN buffer layer have been fabricated on SUS430 substrate by RF reactive magnetron sputtering at room temperature under 50% $N_2$/Ar. The effect of Sc-doping on the structure and piezoelectric properties of AlN films has been investigated using SEM, XRD, surface profiler and pressure-voltage measurements. The as-deposited AlN films showed polycrystalline phase, and the Sc-doped AlN film, the peak of AlN (002) plane and the crystallinity became very strong. With Sc-doping, the crystal size of AlN film was grown from ~20 nm to ~100 nm. The output signal voltage of AlN sensor showed a linear behavior between 15~65 mV, and output signal voltage of Sc-doped AlN sensor was increased over 7 times. The pressure-sensing sensitivity of AlN film was calculated about 10.6mV/MPa, and $Al_{0.88}Sc_{0.12}N$ film was calculated about 76 mV/MPa.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2003년도 하계학술대회 논문집 Vol.4 No.2
• /
• pp.888-891
• /
• 2003

This paper describes on the fabrication and characteristics of micro ceramic thin-film type pressure sensors based on Ta-N strain-gauges for high-temperature applications. The Ta-N thin-film strain-gauges are deposited onto thermally oxidized Si diaphragms by RF sputtering in an argon-nitrogen atmosphere($N_2$ gas ratio: 8 %, annealing condition: $900^{\circ}C$, 1 hr.), Patterned on a wheatstone bridge configuration, and use as pressure sensing elements with a high stability and a high gauge factor. The sensitivity is $1.097{\sim}1.21mV/V.kgf/cm^2$ in the temperature range of $25{\sim}200^{\circ}C$ and the maximum non-linearity is 0.43 %FS. The fabricated pressure sensor presents a lower TCR, non-linearity than existing Si piezoresistive pressure sensors. The fabricated micro ceramic thin-film type pressure sensor is expected to be usefully applied as pressure and load sensors that is operable under high-temperature environments.

• 폴리머
• /
• 제30권3호
• /
• pp.207-209
• /
• 2006

ITO 코팅 글라스를 기판으로 사용하고 폴리(페닐렌에테르설폰)(PES)을 감습막으로 하여 정전용량형 습도센서를 제작하였다. 감습막은 PES를 m-cresol에 용해한 후 스핀코팅으로 제조하였고 그 상부에 다공성 Au막을 스퍼터링으로 증착하였다. 상대습도 $20\sim90%$의 범위에서 센서의 용량은 감습막두께에 반비례하였고 1% 미만의 비선형 특성을 나타내었다. 또한 $1.4{\mu}m$ 두께의 샘플에서는 20 kHz에서 1.3%의 히스테리시스와 1.14의 우수한 감도를 얻을 수 있었다.

• 한국생산제조학회지
• /
• 제19권1호
• /
• pp.7-14
• /
• 2010

AE(acoustic emission) sensor has been used for a state monitoring and observation during a ultra-precision machining because AE signal, which has high frequency range, is sensitive enough. In case of ceramic fabrication, a monitoring of machining state is important because of its hard and brittle nature. A machining characteristic of ceramic is susceptibly different in accordance with variable machining conditions. In this study, Yttria($Y_2O_3$) ceramic was fabricated using the ultra-precision lapping process with in-process electrolytic dressing(IED) method. And the surface machining characteristic and AE sensor signal were compared and analyzed.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2003년도 하계학술대회 논문집 Vol.4 No.2
• /
• pp.884-887
• /
• 2003

Strain gages were widely used transducers. Essentially a strain gage was an electric element to which an appropriate type was attached. Strain was sensed by gages and provided electrical output proportional to applied forced. This paper describes the recent development of a thick film strain gage ceramic pressure sensors. The thick film resistors as strain gage in the Wheatstone bridge were fabricated with a novel mixture of ruthenium. The thick-film technology of resistors were printed on the ceramic diaphragm back side by screen printing and cured at $850^{\circ}C$. The mechanical measurements were performed with the computer simulation results(ANSYS 5.1). The output sensitivity was 1.2mV/V, of which max. nonlinearity was less than 0.29%, hysteresis was less than 0.38%FS.