• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2002.07b
• /
• pp.945-948
• /
• 2002

We studied electro-optical (EO) performances of a vertical-alignment (VA)-in plane switching (IPS) cell on a photopolymer surfaces. The VA-IPS cell, dark in voltage-off state, reveals bright uniformity in all directions due to the dual domainlike dierector configuration in the voltage-on state. For voltage-transmittance (V-T) measurement, the transmittance characteristics of the VA-IPS cell on the photopolymer surface was better than that of the VA-IPS cell on a polyimide(PI) surface.

• Transactions of the Korean hydrogen and new energy society
• /
• v.15 no.3
• /
• pp.175-186
• /
• 2004

In this paper, we developed the dynamic model of a fuel cell system suitable for controller design and system operation. The transient phenomena captured in the model include the flow characteristics and inertia dynamics of the compressor, the intake manifold filling dynamics, oxygen partial pressures and membrane humidity on the fuel cell voltage. In the simulations, we paid attention to the transient behavior of stack voltage and compressor pressure, stoichiometric ratio. Simulation results are presented to demonstrate the model capability. For load current following, stack voltage dynamic characteristics are plotted to understand the Electro-chemistry involved with the fuel cell system. Compressor pressure and stoichiometric ratio are strongly coupled, and independent parameters may interfere with each other, dynamic response, undershoot and overshoot.

• 한국정보디스플레이학회:학술대회논문집
• /
• 2000.01a
• /
• pp.9-10
• /
• 2000

The wide viewing angle and fast response time characteristics of negative dielectric anisotropy nematic liquid crystal (NLC) using a novel vertical-alignment (VA) - 1/4 ${\pi}$ cell mode on a homeotropic alignment layer were investigated. Good voltage-transmittance curves and low driving voltage using the novel VA - 1/4 ${\pi}$ cell mode without a negative compensation film were obtained. The iso-viewing angle characteristics of NLC using the novel VA - 1/4 ${\pi}$ cell mode without a negative compensation film can be achieved. The fast response time of 24.4 ms in NLC was successfully measured. The iso-viewing angle, fast response time, and low driving voltage characteristics using the novel VA - 1/4 ${\pi}$ cell mode can be achieved.

• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2011.10a
• /
• pp.425-428
• /
• 2011

This paper presents a micro-scale solar energy harvesting circuit with a simple MPPT control. Solar Energy is harvested using a small off-chip PV cell generating output voltages under 0.5V instead of an on-chip PV cell. A simple MPPT is implemented using a pilot PV cell and utilizing the relationship between the open-circuit voltage of a PV cell ($V_{OC}$) and its MPP voltage ($V_{MPP}$). With applying the MPPT control, the designed circuit delivers the MPP voltage to load even though the loads is heavy such that the load circuit can operate properly. The proposed circuit is designed in TSMC 0.18um CMOS process.

• Transactions on Electrical and Electronic Materials
• /
• v.14 no.4
• /
• pp.177-181
• /
• 2013

In this paper, silicon solar cells are analyzed regarding power conversion efficiency by changed capacitance in the depletion region. For the capacitance control in the depletion region of silicon solar cell was applied for 10, 20, 40, 80, 160 and 320 Hz frequency band character and alternating current(AC) voltage with square wave of 0.2~1.4 V. Academically, symmetry formation of positive and negative change of the p-n junction is similar to the physical effect of capacitance. According to the experiment result, because input of square wave with alternating current(AC) voltage could be observed to changed capacitance effect by indirectly method through non-linear power conversion (Voltage-Current) output. In addition, when input alternating current(AC) voltage in the silicon solar cell, changed capacitance of depletion region with the forward bias condition and reverse bias condition gave a direct effect to the charge mobility.

• The Transactions of the Korean Institute of Electrical Engineers C
• /
• v.55 no.3
• /
• pp.111-115
• /
• 2006

We investigated accelerated soft error rate(ASER) in 8M static random access memory(SRAM) cells. The effects on ASER by well structure, operational voltage, and cell transistor threshold voltage are examined. The ASER decreased exponentially with respect to operational voltage. The chips with buried nwell1 layer showed lower ASER than those either with normal well structure or with buried nwell1 + buried pwell structure. The ASER decreased as the ion implantation energy onto buried nwell1 changed from 1.5 MeV to 1.0 MeV. The lower viscosity of the capping layer also revealed lower ASER value. The decrease in the threshold voltage of driver or load transistor in SRAM cells caused the increase in the transistor on-current, resulting in lower ASER value. We confirmed that in order to obtain low ASER SRAM cells, it is necessary to also the buried nwell1 structure scheme and to fabricate the cell transistors with low threshold voltage and high on-current.

• Journal of Electrochemical Science and Technology
• /
• v.9 no.3
• /
• pp.195-201
• /
• 2018

To enhance the performance of cathodes at low temperatures, a Cu-coated cathode is prepared, and its electrochemical performance is examined by testing its use in a single cell. At $620^{\circ}C$ and a current density of $150mAcm^{-2}$, a single cell containing the Cu-coated cathode has a significantly higher voltage (0.87 V) during the initial operation than does that with an uncoated cathode (0.79 V). According to EIS analysis, the high voltage of the cell with the Cu-coated cathode is due to the dramatic decrease in the high-frequency resistance related to electrochemical reactions. From XPS analysis, it is confirmed that the Cu is initially in the form of $Cu_2O$ and is converted into CuO after 150 h of operation, without any change in the state of the Ni or Li. Therefore, the high initial cell voltage is confirmed to be due to $Cu_2O$. Because $Cu_2O$ is catalytically active toward $O_2$ adsorption and dissociation, $Cu_2O$ on a NiO cathode enhances cell performance and reduces cathode polarization. However, the cell with the Cu-coated cathode does not maintain its high voltage because $Cu_2O$ is oxidized to CuO, which demonstrates similar catalytic activity toward $O_2$ as NiO.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.62 no.12
• /
• pp.1792-1797
• /
• 2013

Recently, due to the excessive use of fossil fuels, many studies about the fossil fuels such as solar and fuel cell energy source are progressing. Fuel cell system has high energy conversion efficiency. Also, fuel cell system is environmentally friendly system because the carbon emission is almost not occur. Therefore, the fuel cell system is considered as the core technology of in the fields of the future energy and environmental. Fuel cell system has an effect on distribution power system because another power source of other than large power plants. So, fuel cell system can be reason of power quality in the power system. In this paper, we constructed the system for an assessment on Islanding. The system is composed with power source, Impedance coordination load and linear load, fuel cell system. we are performed assessment on voltage and power quality in customer and the distributed power system during the Islanding of residential fuel cell system. In addition, no change in the impedance of power system, we made a islanding condition only using the actual load, As a variation of generation and load current under islanding, an analysis results based on assessment system showed that the power qualities of distribution system became more aggravation as effect of voltage sag and voltage swell phenomena.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.23 no.4
• /
• pp.273-280
• /
• 2018

This paper proposes a zero-voltage-transition pulse-width modulation (PWM) DC-DC converter that uses a new active-snubber-cell. The converter main switch can be turned on and off with ZVS, while the snubber switch is turned on with ZCS and turned off with ZVS. Other semiconductor devices are operated under the soft-switching condition. Normal PWM control can be used, the proposed active-snubber-cell does not impose any additional voltage and current stresses. The active-snubber-cell is suitable for high-power applications due to its easy integration into interleaved converters. This paper discusses the operation of the converter, presents some design guidelines, and provides the results of an experiment with a 100 kHz and 1 kW prototype. A peak efficiency of 97.8% is recorded.

• Proceedings of the KIEE Conference
• /
• 1994.07a
• /
• pp.183-185
• /
• 1994

A new method for determination of electric parameter of cell membranes is proposed. Two circular electrodes is designed to have repulsive force. From the potential energy analysis, stable points where a cell is levitated between electrodes exist and move as frequency or voltage change. The levitated cell in the stable point fall freely when DEP force is zero. The DEP force is dependent on the frequency and the force is zero at the critical frequency. The critical frequency is determined by measuring the difference between the time taken at zero-applied voltage and the time taken at the frequency and the voltage. For example, the critical frequency and stable points of N.crassa slime cell is numerically evaluated. In the exeriment, polystyrene in water is levitated at the stable point. We show that the stable point move as the applied voltage is changed.