• 제목/요약/키워드: Cell Densification

검색결과 24건 처리시간 0.027초

CDMA 이동통신 시스템의 스펙트럼 이용효율 분석 (Spectrum Usage Efficiency of CDMA System)

  • 김종호;최상성;이형수
    • 한국전자파학회:학술대회논문집
    • /
    • 한국전자파학회 2003년도 종합학술발표회 논문집 Vol.13 No.1
    • /
    • pp.576-580
    • /
    • 2003
  • In order to assess the spectrum usage efficiency in mobile radio services, we consider the capacity limits of a CDMA system. The maximum achievable capacity per $km^2$ is viewed as a meaningful figure of merit for a cellular system and a method is proposed here to estimate the minimum achievable distance between adjacent base stations in the case of CDMA. The probability for entering in soft handover state is used as a limit for densification in a CDMA system. From this criterion, conditions on the minimum possible cell radius are derived.

  • PDF

급속 소결에 의한 인공관절용 나노구조 2/3 Cr-ZrO2 복합재료 제조 및 특성 (Properties and Fabrication of Nanostructured 2/3 Cr-ZrO2 Composite for Artificial Joint by Rapid Sinerting)

  • 강현수;강보람;손인진
    • 한국재료학회지
    • /
    • 제24권9호
    • /
    • pp.495-501
    • /
    • 2014
  • Despite having many attractive properties, $ZrO_2$ ceramic has a low fracture toughness which limits its wide application. One of the most obvious tactics to improve its mechanical properties has been to add a reinforcing agent to formulate a nanostructured composite material. Nanopowders of $ZrO_2$ and Cr were synthesized from $CrO_3$ and Zr powder by high energy ball milling for 10 h. Dense nanocrystalline $2/3Cr-ZrO_2$ composite was consolidated by a high-frequency induction heated sintering method within 5 min at $600^{\circ}C$ from mechanically synthesized powder. The method was found to enable not only rapid densification but also the inhibition of grain growth, preserving the nano-scale microstructure. Highly dense $2/3Cr-ZrO_2$ composite with relative density of up to 99.5% was produced under simultaneous application of a 1 GPa pressure and the induced current. The hardness and fracture toughness of the composite were 534 kg/mm2 and $7MPa{\cdot}m1/2$, respectively. The composite was determined to have good biocompatibility.

고에너지 볼밀링에 의해 제조된 Gd2O3-doped CeO2 나노분말의 소결 거동에 관한 연구 (Sintering Behavior of Nano-sized Gd2O3-doped CeO2 Powder Prepared by A High Energy Ball Milling)

  • 류성수;김형태
    • 한국분말재료학회지
    • /
    • 제15권4호
    • /
    • pp.302-307
    • /
    • 2008
  • $Gd_2O_3$-doped $CeO_2$(GDC) solid solutions have been considered as a promising materials for electrolytes in intermediate-temperature solid oxide fuel cells. In this study, the nano-sized GDC powder with average panicle size of 69nm was prepared by a high energy ball milling process and its sintering behavior was investigated. Heat-treatment at $1200^{\circ}C$ of nano-sized GDC powder mixture led to GDC solid-solution. The enhanced densification over 96% of relative density was obtained after sintering at $1300^{\circ}C$ for 2h. It was found that the sinterability of GDC powder could be significantly improved by the introduction of a high energy ball milling process.

DC 스퍼터법과 비대칭 양극성 펄스 스퍼터법으로 제작된 고분자 전해질 연료전지 금속분리판용 CrN 코팅막의 특성 연구 (A Comparative Study of CrN Coatings Deposited by DC and Pulsed DC Asymmetric Bipolar Sputtering for a Polymer Electrolyte Membrane Fuel Cell (PEMFC) Metallic Bipolar Plate)

  • 박상원;전성용
    • 한국세라믹학회지
    • /
    • 제50권6호
    • /
    • pp.390-395
    • /
    • 2013
  • Nanocrystalline CrN films were deposited on Si (100) substrates by means of asymmetric pulsed DC reactive magnetron sputtering. We investigated the growth behavior, corrosion resistance and mechanical properties of CrN films with a change in the duty cycle and pulse frequency. The grain size of the CrN films decreased from 25.4 nm to 11.2 nm upon a decrease in the duty cycle. The corrosion potentials for the CrN films by DC sputtering was approximately - 0.6 V, and it increased to - 0.3 V in the CrN films which underwent pulsed sputtering. The nanoindentation hardness of the CrN films also increased with a decrease in the duty cycle. This enhancement of the corrosion resistance and mechanical properties of pulsed sputtered CrN films could be attributed to the densification and surface smoothness of the microstructure of the films.

압분공정의 유한요소 해석을 위한 AZO 분말의 Closed-die Compaction 실험 (Closed-die Compaction of AZO Powder for FE Simulation of Powder Compaction)

  • 김용배;이종섭;이상목;박훈재;이근안
    • 소성∙가공
    • /
    • 제21권4호
    • /
    • pp.228-233
    • /
    • 2012
  • In this study, powder compaction of AZO (alumina doped zinc oxide) powder was performed with a MTS 810 test system using a cylindrical die having a diameter of 10mm. Pressure-density curves were measured based on the load cell and displacement of the punch. The AZO powder compacts with various densities were formed to investigate the mechanical properties such as fracture stress of the AZO powder as a function of the compact density. Two types of compression tests were conducted in order to estimate the fracture stress using different loading paths: a diameteral compression test and a uniaxial compression test. The pressure-density curves of the AZO powder were obtained and the fracture stress of the compacted powders with various densities was estimated. The results show that the compact pressure dramatically increases as the density increases. Based on the experimental results, calibration of the modified Drucker-Prager/Cap model of the AZO powder for use in FE simulations was developed.

Characteristics of Expanded Graphite Filled Conductive Polymer Composites for PEM Fuel Cell Bipolar Plates

  • Oh, K.S.;Heo, S.I.;Yun, J.C.;Yang, Y.C.;Han, K.S.
    • Advanced Composite Materials
    • /
    • 제17권3호
    • /
    • pp.259-275
    • /
    • 2008
  • This study aims to optimize the mechanical and electrical properties of electrically conductive polymer composites (CPCs) for use as a material of bipolar plates for PEM fuel cells. The thin CPCs consisting of conductive fillers and polymer resin were fabricated by a preform molding technique. Expanded graphite (EG), flake-type graphite (FG) and carbon fiber (CF) were used as conductive fillers. This study tested two types of CPCs, EG/FG filled CPCs and EG/CF filled CPCs, to optimize the material properties. First, the characteristics of EG/FG filled CPCs were investigated according to the FG ratio for 7 and $100{\mu}m$ sized FG. CPCs using $100{\mu}m$ FG showed optimal material properties at 60 wt% FG ratio, which were an electrical conductivity of 390 S/cm and flexural strength of 51 MPa. The particle size was an important parameter to change the mechanical and electrical behaviors. The flexural strength was sensitive to the particle size due to the different levels of densification. The electrical conductivity also showed size-dependent behavior because of the different contributions to the conductive network. Meanwhile, the material properties of EG/CF filled CPCs was also optimized according to the CF ratio, and the optimized electrical conductivity and flexural strength were 290 S/cm and 58 MPa, respectively. The electrical conductivity of this case decreased similarly to the EG/FG filled case. On the other hand, the behavior of the flexural strength was more complicated than the EG/FG filled case, and the reason was attributed to the interaction between the strengthening effect of CF and the deterioration of voids.

고밀도 폴리우레탄 폼의 극저온 성능 분석 (Investigation of the Cryogenic Performance of the High Density Polyurethane Foam)

  • 김정현;김정대;김태욱;김슬기;이제명
    • 한국산업융합학회 논문집
    • /
    • 제26권6_3호
    • /
    • pp.1289-1295
    • /
    • 2023
  • Polyurethane foam insulation required for storing and transporting cryogenic liquefied gas is already widely used as a thermal insulation material for commercial LNG carriers and onshore due to its stable price and high insulation performance. These polyurethane foams are reported to have different mechanical performance depending on the density, and the density parameter is determined depending on the amount of the blowing agent. In this study, density-dependent polyurethane foam was fabricated by adjusting the amount of blowing agent. The mechanical properties of polyurethane foam were analyzed in the room temperature and cryogenic temperature range of -163℃ at 1.5 mm/min, which is a quasi-static load range, and the cells were observed through microstructure analysis. The characteristics of linear elasticity, plateau, and densification, which are quasi-static mechanical behaviors of polyurethane foam, were shown, and the correlation between density and mechanical properties in a cryogenic environment was confirmed. The correlation between mechanical behavior and cell size was also analyzed through SEM morphology analysis. Polyurethane foam with a density of 180 kg/m3 had a density about twice as high as that of a polyurethane foam with a density of 96 kg/m3, but yield strength was about 51% higher and cell size was about 9.5% smaller.

소형 콘의 온도보상 기법 연구 (Study of Temperature Compensation method in Mini-Cones)

  • 윤형구;정순혁;조세현;이종섭
    • 대한토목학회논문집
    • /
    • 제31권1C호
    • /
    • pp.29-38
    • /
    • 2011
  • 소형 콘은 해상도가 뛰어나 국부영역의 탐지를 위하여 다양하게 활용되고있다. 소형 콘은 변형률계 부착 면적이 부족하여 half-bridge 형태로 회로를 구성하고 있으며, 이는 주변온도 변화에 의하여 민감하게 반응하는 것으로 알려져있다. 본 논문의 목적은 이러한 온도영향을 해소하기 위하여 소형 콘의 온도보상 기법에 관한 연구를 수행하는 것이다. 본 연구를 수행하기 위하여 직경과 길이가 각각 15mm 그리고 56mm인 소형 콘을 개발하였다. 로드셀은 온도변화만을 반영할 수 있는 공간을 확보하기 위하여 후면으로 54mm 연장하여 제작되었다. 온도보상회로는 스트레인 게이지를 선단저항 부분, 주면마찰 부분 그리고 연장한 로드셀에 부착하여 소형 콘 내에서 휘트스톤 브리지(Wheatstone bridge) 회로를 구성하였다. 소형 콘의 일반적 회로구성인 half-bridge도 내부에 함께 구성하여 상호간의 결과값을 비교 및 고찰하였다. 여름과 겨울의 계절적인 온도변화에 따라 측정값의 오차를 검증하기 위하여 계절적 온도 변화 실험을 수행하였다. 또한 지반다짐 실험으로 지반의 상대밀도를 증가시켜 관입 시 주변 온도변화에 따라 측정값 변화도 관찰하였다. 측정결과 온도보상회로를 이용하여 측정한 값은 half-bridge 회로로 측정한 값과 차이를 보였으며, 더욱 안정화되고 이상적인 경향을 보였다. 본 논문은 소형 콘 사용시 온 도 영향에 대한 문제를 해소하고 더욱 신뢰성 높은 측정값을 획득할 수 있는 기법에 대하여 제시하였다.

온도보상형 전기비저항 프로브 - 개발 및 적용 (Temperature-compensated Resistivity Probe - Development and Application)

  • 정순혁;윤형구;이종섭
    • 한국지반환경공학회 논문집
    • /
    • 제12권1호
    • /
    • pp.51-60
    • /
    • 2011
  • 전기비저항은 지층의 자세한 이해와 지반의 기본 물성치 획득을 위하여 다양한 측정 장비에 적용되고 있다. 본 연구의 목적은 프로브가 관입되는 동안 온도가 전기비저항에 미치는 영향을 상쇄시켜 보다 정밀한 전기비저항을 평가할 수 있는 온도보상형 전기비저항 프로브(TRP)를 개발하고 적용하는 것이다. 전기비저항 콘의 직경에 따른 온도변화를 분석하기 위하여 두가지 직경(2mm, 5mm)의 콘을 제작하였다. 온도 센서는 전기비저항 프로브와의 전기적 간섭현상을 고려하여 선단부에서 15mm 떨어진 곳에 부착하였다. 또한 모터식 관입기와 전기비저항 프로브 사이의 전기적 교란을 막기 위하여 절연 커넥터를 이용하였다. 직경 30cm의 아크릴 수조에 주문진사를 수중강사법으로 시료를 조성하고 타격에 의해 상대밀도를 증가시키면서 실험을 진행하였다. 실험결과, 관입되는 동안 프로브의 온도가 증가하였으며, 정확한 전기비저항 프로파일을 산정하기 위하여 온도보정이 필요한 것으로 나타났다. 본 연구에서는 온도보상형 전기비저항 프로브(TRP)를 개발하고, 이를 관입실험에 적용하여 정확한 지반조사를 수행하기 위해서는 온도에 대한 영향 및 관입특성을 고려해야 함을 보여준다.

초미세 분쇄 분말로 제조된 K+-beta-aluminas의 치밀화 연구 (Densification Study of K+-beta-aluminas Prepared from Their Ultra-fine Milled Powder)

  • 신재호;김우성;임성기
    • 공업화학
    • /
    • 제16권5호
    • /
    • pp.648-652
    • /
    • 2005
  • 대기압하에서 소결이 어렵다고 알려진 초이온 전도체인 $K^+$-beta-aluminas를 attrition mill을 이용하여 약 350 nm의 평균 입도를 가지는 분말로 분쇄한 후, 시편을 일축가압 성형하여 상압 하에서 동일조성의 분위기 분말을 이용하여 소결하였다. 소결온도는 $1400^{\circ}C{\sim}1650^{\circ}C$까지 $50^{\circ}C$ 간격으로 소결하였으며, 각 소결온도에서 시간에 따른 소결특성을 살펴보았다. 또한 고온에서 입자 성장 속도를 조절하기 위하여 $1600^{\circ}C$에서 zone sintering을 실시하였다. $1600^{\circ}C$$1650^{\circ}C$에서 소결한 경우와 $1600^{\circ}C$에서 zone sintering한 시편의 경우, 각각 약 93%와 95%의 소결 밀도를 나타내었다. $1600^{\circ}C$ 이상의 온도에서 2 h 이상 장시간 소결할 경우, 입자의 거대성장으로 인하여 소결밀도가 90% 미만으로 감소하였다.