• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.19 no.9
• /
• pp.474-481
• /
• 2018

The policy-making and technological development of eco-friendly automobiles designed to increase their supply is ongoing, but the internal combustion engine still accounts for approximately 95% of automobiles in use. To meet the stricter emission regulations of internal combustion engines based on fossil fuels, the proportion of after-treatments for vehicles and (ocean going) vessels is increasing continuously. As diesel engines have high power and good fuel economy in addition to less CO2 emissions, their market share is increasing not only in commercial vehicles, but also in passenger cars. Because of the characteristics of the diesel combustion, however, NOx is generated in localized high-temperature combustion regions, and particulates are formed in the zones of diffusion combustion. LNT and urea-SCR catalysts have been developed for the after-treatment of exhaust gas to reduce NOx in diesel vehicles. This study examined the effect of a containing promoter on SCR catalysts to cope with the severe exhaust gas regulation. The de-NOx performance of the Mn-SCR catalyst was the best, and the de-NOx performance was improved as the ion exchange rate between Mn ion and Zeolyst was good and the activation energy was low. The de-NOx performance of the 7Cu-15Ba/78Zeoyst catalyst was 32% at $200^{\circ}C$ and 30% at $500^{\circ}C$, and showed the highest performance. The NOx storage material of BaO loaded as a promoter was well dispersed in the Cu-SCR catalyst and the additional de-NOx performance of BaO was affected by the reduction reaction of the Cu-SCR catalyst. Among the three catalysts, the 7Cu-15Ba/Zeolyst SCR catalyst was resistant to thermal degradation. The same type of CuO due to thermal degradation migrates and agglomerates because BaO reduces the agglomeration of the main catalyst CuO particles.

• Korean Journal of Microbiology
• /
• v.38 no.1
• /
• pp.13-18
• /
• 2002

Effects of divalent cations such as $Mg^{2+}$, $Mn^{2+}$ and $Zn^{2+}$ on the self-splicing inhibition of the T4 phage thymidylate synthase (td) intron by the coenzyme thiamine pyrophosphate have been investigated. The splicing activity increased in proportion to the concentration of $Mg^{2+}$ up to 30 mM. Without $Mg^{2+}$in the splicing reaction the $Zn^{2+}$ ion tested in the range of 0.1-6 mM concentration only produced the splicing activity about 20% that of the normal splicing rate. A majority of the splicing products were I-E2 and E2 but El-E2 ligation product, Cl and Ll were not detected. Similar patterns of splicing products were also observed with $Mn^{2+}$. At 6 mM $Zn^{2+}$the intron RNA was hydrolyzed. $Mn^{2+}$produced a little higher splicing activity than that of $Zn^{2+}$over the range of concentrations used and at 8 mM about 28% splicing activity was observed. In contrast, $Mn^{2+}\;and\;Zn^{2+}$ ions promoted the splicing activity about 35-40% on an average in the presence of 10 mM $Mg^{2+}$. Of all divalent cations tested, $Mg^{2+}$exhibited the maximum activation effect to counteract the splicing inhibition by thiamine pyrophosphate. This appears to be due to the stabilizing effect of td intron ribozyme structure essential for the catalytic function by $Mg^{2+}$.

• Journal of Sensor Science and Technology
• /
• v.9 no.1
• /
• pp.28-35
• /
• 2000

In this study, we investigated the characteristics of polyurethane synthesis by simultaneously measuring resonant frequency and resonant resistance with a quartz crystal analyzer. The rapid decrease of resonant frequency was appeared because automatic catalytic reaction was caused by the polyurethane formed in initial stage of polyurethane synthesis. In prepolymer(PP) synthesis, the resonant frequency was slowly stabilized after a rapid decrease at a certain point of time. But in segmented polyurethane synthesis in which chain-extender was involved, the resonant frequency increased again after a rapid decrease at a certain point of time. It was considered that this tendency took place because the chain-extender, 1,4-butandiol, caused a soft segment to change to a hard segment. The resonant resistance was used in the analysis of mechanism. From the results, the characteristics of polyurethane synthesis could be analyzed on-line using a quartz crystal analyzer, and the synthesis mechanism could also be interpreted.

• Applied Chemistry for Engineering
• /
• v.17 no.3
• /
• pp.235-242
• /
• 2006

Liquid phase alkylation of biphenyl (BP) was studied over large pore zeolites. Selective formation of the least bulky products, 4,4'-diisopropylbiphenyl (4,4'-DIPB) occurred only in the isopropylation of BP over some large pore molecular sieves. H-mordenites (MOR) gave the highest selectivity among them. The dealumination of MOR enhanced catalytic activity and the selectivity of 4,4'-DIPB because of the decrease of coke-deposition. Non-selective catalysis occurs on external acid sites over MOR with the low $SiO_2/Al_2O_3$ ratio because severe coke-deposition deactivates the acid sites inside the pores by blocking pore openings. The selectivity of DIPB isomers was changed with reaction temperature. Selective formation of 4,4'-DIPB was observed at moderate temperatures such as $250^{\circ}C$, whereas the decrease of the selectivity of 4,4'-DIPB occurred at higher temperatures as $300^{\circ}C$. However, 4,4'-DIPB was almost exclusive isomer in the encapsulated DIPB isomers inside the pores even at high temperatures. These decreases of the selectivity of 4,4'-DIPB are due to the isomerization of 4,4'-DIPB on the external acid sites. Some 12-membered molecular sieves, such as SSZ-24, MAPO-5 (M:Mg, Zn, Si), SSZ-31, and ZSM-12, which have straight channels, gave 4,4'-DIPB with moderate to high selectivity; however; SSZ-55, SSZ-42, and MAPO-36 (M: Mg, Zn) gave lower selectivity because of cages in 12-membered one dimensional channels. Three dimensional H-Y and Beta zeolites also yield 4,4'-DIPB in low yield because of their wide circumstances for the isopropylation of BP. The increasing the size of alkylating agent enhanced the shape-selective alkylaiton even for the zeolites, such as UTD-1. The ethylation of BP to ethylbiphenyls (EBPs) and diethylbiphenyls (DEBPs) over MOR was non-selective. The ethylation of BP to EBPs was controlled kinetically. However, there was difference in reactivity of EBPs and DEBPs for their further ethylation. 4-EBP was ethylated preferentially among the isomers, although the formation of 4,4'-DEBP was less selective. The least bulky 4-EBP and 4,4'-DEBP have the highest reactivity among EBPs and DEBPs for the ethylation to polyethylbiphenyls (PEBPs). These results show that the environments of MOR pores are too loose for shape selective formation of the least bulky isomers, 4-EBP and 4,4'-DEBP in the ethylation of BP, and that MOR pores have enough space for the further ethylation of 4,4'-DEBP.

• Applied Chemistry for Engineering
• /
• v.10 no.8
• /
• pp.1129-1135
• /
• 1999

The reduction of $SO_2$ by CO over supported cobalt catalysts was investigated within the temperature range of $350{\sim}550^{\circ}C$, initial $SO_2$ concentration of 1000~10000 ppm, $CO/SO_2$ molar ratio of 1.0~3.0 and space velocity of $5000{\sim}15000h^{-1}$. Several types of supports such as ${\gamma}-Al_2O_3$, $TiO_2$ were tested. The $SO_2$ conversion and selectivity to elemental sulfur were investigated using a differential fixed bed reactor at atmospheric pressure. The catalyst prepared by wet impregration of 5 wt % cobalt on ${\gamma}-Al_2O_3$ showed $SO_2$ conversion higher than 90% and COS yield lower than 6% at temperature above $400^{\circ}C$. The optimum $CO/SO_2$ molar ratio was investigated as 2.0. At higher $CO/SO_2$ molar ratio, the $SO_2$ conversion became higher but the main product was COS. The effect of $SO_2$ concentration and space velocity over $SO_2$ conversion and COS yield was not appreciable in the experimental range. The activated cobalt phase was detected as $CoS_2$ and the $CoS_2$ phase unchanged even after reaction.

• Applied Chemistry for Engineering
• /
• v.23 no.3
• /
• pp.302-307
• /
• 2012

Advanced oxidation processes (AOP) such as O3/activated carbon process and O3/catalysts process were used to compare the decomposition of phenol. Catalysts such as Pd/activated carbon (Pd/AC), Mn/activated carbon (Mn/AC), Co/activated carbon (Co/AC) and Fe/activated carbon (Fe/AC) were prepared by impregnation of Pd, Mn, Co and Fe into the activated carbon of pellet form, respectively. Based on an hour of reactions, the following descending order for the decomposition ratios of dissolved O3 to the 1.48 mg/L of saturated dissolved O3 was observed: Mn/AC (45%) > Pd/AC (42%) > Co/AC (33%) > AC (31%) > Fe/AC (27%). The removal efficiencies of phenol were also arranged in the descending order of AOP as follows: Mn/AC (89%) > Pd/AC (85%) > Co/AC (77%) > AC (76%) > Fe/AC (71%). The remaining ratios (C/Co) of TOC (total organic carbon) after an hour of experiments were arranged in the ascending order of AOP as follows : Pd/AC (0.29) < Mn/AC (0.36) < AC (0.40) < Co/AC (0.49) < Fe/AC (0.51). However, the catalytic effects in the Co/AC and the Fe/AC processes were little in comparison with O3/AC process. The maximum concentrations of intermediates such as hydroquinone and catechol formed from the decomposition of phenol were arranged in the ascending order of AOP as follows: Pd/AC < Fe/AC < Co/AC < AC < Mn/AC. In the case of Pd/AC process, these intermediates were almost disappeared after an one hour of reaction.

• Applied Chemistry for Engineering
• /
• v.7 no.3
• /
• pp.543-553
• /
• 1996

Oxygen reduction in an alkaline fuel cell was studied by using perovskite type oxides as an oxygen electrode catalyst. The high surface area catalysts were prepared by malic acid method and had a formula of $La_{0.6}Sr_{0.4}Co_{1-x}Fe_xO_3$(x=0.00, 0.01, 0.10, 0.20, 0.35 and 0.50). From the result of XRD pattern and specific surface area due to the amount of Fe substitution and the consumption of ammonia-water, the complex formation of Fe ion with $NH_3$ was the main factor for both the phase stability of perovskite and the increase of specific surface area. Multi-step calcination was necessary to give a single phase of perovskite in catalyst precursor. The crystal structure of the catalysts was simple cubic perovskite, which was verified from the XRD patterns of the catalysts. The activity of oxygen reduction was monitored by the techniques of cyclic voltammetry, static voltage-current method, and current interruption method. The activity(current density) of oxygen reduction showed its minimum at x=0.01 and its maximum between 0.20 and 0.35 of x-value in $La_{0.6}Sr_{0.4}Co_{1-x}Fe_xO_3$. This tendency was independent of the change of surface area.

• Journal of Korean Society of Environmental Engineers
• /
• v.28 no.3
• /
• pp.323-328
• /
• 2006

The purpose of this paper was to investigate the reforming characteristics and optimum operating condition of the GlidArc-assisted $C_3H_8$ reforming reaction for the synthesis gas(SynGas) production without formation of carbon black from propane using GildArc plasma reforming. Also, in order to increase the hydrogen production and the propane conversion rate, 13 wt % nickel catalyst was filled into the catalytic reactor and parametric screening studies were conducted, in which there were the variations of vapor mole ratio$(H_2O/C_3H_8),\;CO_2$ mole ratio($CO_2/C_3H_8$), input power and injection flow rate. When the variations of vapor mole ratio, $CO_2$ mole ratio, input power and injection flow rate were 1.86, 0.48, 1.37 kW and 14 L/min, respectively, the conversion rate of the propane reached its most optimal condition, or 62.6%. Under the condition mentioned above, the dry basic concentrations of the SynGas were $H_2\;44.4%,\;CO\;18.2%,\;CH_4\;11.2%,\;C_2H_2\;2.0%,\;C_3H_6\;1.6%,\;C_2H_4\;0.6%\;and\;C_3H_4$ 0.4%. The conversion rate of carbon dioxide was 29.2% and the concentration ratio of hydrogen to carbon monoxide($H_2/CO$) in the SynGas was 2.4.

• Journal of the Korean Applied Science and Technology
• /
• v.33 no.1
• /
• pp.67-74
• /
• 2016

The Prussian Blue Analogue(PBA) has three dimensional structure and the metal - organic framework material, and it has a variety configurations depending on the type of organic ligands. PBA has been receving an attention in the fields of biosensors, optical, catalytic, and hydrogen storage device. Also, it is an environmental friendly substance with a chemical stability. In addition, PBA is widely used in the filed of adsorption art since we can adjust the size of the fine pores. In this study, we synthesized $Mn_3[Fe(CN)_6]_2$, an organometallic framework chains by using a hydrothermal synthesis method. We used $K_4[Fe(CN)_6]$ and $MnCl_2$ as precursors. We also produced a manganese iron oxide, by baking the synthesized material. The effect of the size and shape of the particles was examined by controling pH of the precursor solution, the molar concentration of the precursor, and reaction time as the experimental variables. Synthesized absorbent was analyzed by XRD, SEM, FT-IR, UV-Vis, and TG / DTA to evaluate the adsorption properties of several dyes.

• Korean Chemical Engineering Research
• /
• v.46 no.4
• /
• pp.806-812
• /
• 2008

The ammonia decomposition reaction has been of increasing interest as a means of treating ammonia in flue gas in the presence of precious metal catalyst. Various catalysts, $Pt-Rh/Al_2O_3$, $Pt-Rh/TiO_2$, $Pt-Rh/ZrO_2$, $Pt-Pd/Al_2O_3$, $Pd-Rh/Al_2O_3$, $Pd-Rh/TiO_2$, $Pd-Rh/ZrO_2$, $Pt-Pd-Rh/Al_2O_3$, $Pd/Ga-Al_2O_3$, $Rh/Ga-Al_2O_3$, and Ru/Ga-$Al_2O_3$, were synthesized by using excess wet impregnation method. Using a homemade 1/4" reactor at $10,000{\sim}50,000hr^{-1}$ of space velocity in the presence of precious metal catalyst ammonia decomposition reactions were carried out to investigate the catalyst activity. The inlet ammonia concentration was maintained at 2,000 ppm, with an air balance. Both $T_{50}$ and $T_{90}$, defined as the temperatures where 50% and 90% of ammonia, respectively, are converted, decreased significantly when alumina-supported catalysts were applied. In terms of catalytic performance on the ammonia conversion in the presence of hydrogen sulfide, $Pt-Rh/Al_2O_3$ catalyst showed no effect on the poisoning caused by hydrogen sulfide. These results indicate that platinum-rhodium bimetallic catalyst is a useful catalyst for ammonia decomposition.