• Composites Research
• /
• v.16 no.3
• /
• pp.75-84
• /
• 2003

The purpose of this study is to investigate the wear properties of Saffil/Al, Saffil/A12O3/Al and Saffil/SiC/Al hybrid metal matrix composites fabricated by squeeze casting method. Wear tests were done on a pin-on-disk friction and wear tester under both dry and lubricated conditions. The wear properties of the three composites were evaluated in many respects. The effects of Saffil fibers, $\textrm{Al}_2\textrm{O}_3$ particles and SiC particles on the wear behavior of the composites were investigated. Wear mechanisms were analyzed by observing the worn surfaces of the composites. The variation of coefficient of friction(COF) during the wear process was recorded by using a computer. Under dry sliding condition, Saffil/SiC/Al showed the best wear resistance under high temperature and high load, while the wear resistances of Saffil/Al and Saffi1/$\textrm{Al}_2\textrm{O}_3$/Al were very similar. Under dry sliding condition, the dominant wear mechanism was abrasive wear under mild load and room temperature, and the dominant wear mechanism changed to adhesive wear as load or temperature increased. Molten wear occurred at high temperature. Compared with the dry sliding condition, all three composites showed excellent wear resistance when lubricated by liquid paraffin. Under lubricated condition, Saffil/Al showed the best wear resistance among them, and its COF value was the smallest. The dominant wear mechanism of the composites under lubricated condition was microploughing, but microcracking also occurred to them to different extents.

• Journal of Korean Society of Occupational and Environmental Hygiene
• /
• v.27 no.4
• /
• pp.302-312
• /
• 2017

Objectives: In this study, an evaluation of the working environment of furnace workers was performed and the work-relatedness of the occupational diseases were examined Methods: In this study, two electric furnaces at a single casting business site producing manganese-based iron alloy were selected, and occupational exposures to hazardous substances were evaluated for furnace workers and furnace worker assistants. Results: As a result, total dust concentration were $0.407{\sim}3.001mg/m^3$ and respirable dust concentration were $0.196{\sim}0.584mg/m^3$. The highest concentration of crystalline silica was $0.079mg/m^3$ In the case of Masato and Sosuckwhoi crystalline silica, they contained 90.85% and 4.17% respectively. Manganese concentration was the highest at a $0.205mg/m^3$ maximum. The average of black carbon is $11.56{\mu}g/m^3$ and the maximum concentration is $604.23{\mu}g/m^3$. PAHs concentration was the highest at a $78.301{\mu}g/m^3$ of naphthalene. The concentration of carbon monoxide was 18.82 ppm(total average 3.89 ppm) during pouring, and the maximum is 131 ppm. The formaldehyde concentration was 0.003 to 0.007 ppm. Conclusions: It seems that conditions in the past were worse, since casting has recently been performed only twice per day for about 20 minutes, reducing the amount of pouring, and local exhaust systems have been installed one-by-one. In addition, it was judged that the past exposure levels were higher considering the points measured on the back-side due to the risk of damage to the individual samples. It was found that operators could be exposed to high concentrations of crystalline silica, and that they were also exposed to high concentrations of metal(fume) and carbon monoxide during pouring. Therefore, there is a risk that occupational diseases such as lung cancer and COPD may occur with long-term work in such a process.

• Journal of the Korean Magnetics Society
• /
• v.13 no.4
• /
• pp.182-186
• /
• 2003

A new axial pressing method using pulse magnetizing field was studied to improve the remanence of Nd-Fe-B sintered magnets. In order to make near-net shape green compacts of butterfly, disk, or coin magnets, conventional axial-type pressing has been normally used. However, compared to the transverse-type pressing, it is not possible to obtain higher remanence by this method because the magnetic alignment of powder begins to deteriorate when the density of green compacts increases over a critical value. On the other hand, we found that an axial pressing under pulse magnetizing field was very effective to increase the degree of magnetic alignment of powder, yielding remanences even higher than those obtained by the transverse pressing. In this study, it was revealed that appropriate tapping density and how to apply pulse magnetic held were important to improve the grain alignment and thus remanence of Nd-Fe-B sintered magnet.

• Journal of the Korean Society for Marine Environment & Energy
• /
• v.6 no.2
• /
• pp.38-45
• /
• 2003

This paper intends to analyze the movement characteristics of the suspended solid(SS) generated in a riprap work which is the most widespread process in harbor construction. The generation and movement behaviors of SS are investigated when 1) basic ripraps (0.001~0.03㎥) are cast for breakwater construction, 2) ripraps are loaded on carrier for riprap casting in the sea-wall construction of dredged material pocket, and 3) ripraps for inner filling are cast. The result of the present study shows that the SS generation is considerable when basic ripraps are cast for breakwater construction and the SS diffusion reaches up to 500m in high tide period. When ripraps are loaded on carrier, the SS is generated by the ripraps running down into sea from carrier, thereby showing a high concentration of SS in the vicinity of carrier. In the surface layer, SS distribution is confined in the vicinity of the carrier due to the prompt sinking of the SS. However the SS in the bottom layer is diffused approximately up to loom and then the SS concentration reaches to the background one. In the riprap (less than 0.03㎥) casting for inner filling using pork crane, SS is diffused approximately up to 300m in the surface layer and more than 300m in the bottom layer. It is quite interesting that the movement of the SS generated in harbor construction is mainly controlled by wind drift in the surface layer and tidal current in the bottom layer, and also the diffusion range of SS in the bottom layer is much larger than that in the surface layer.

• Korean Journal of Materials Research
• /
• v.3 no.3
• /
• pp.253-260
• /
• 1993

High strength and fracture toughness of Al-Li-Cu alloy(2090 Al alloy) have been achieved by the improvement of melting and casting, extrusion and heat treatment techniques. To establish the sucessful process for semi-industrial scale ingot(20Kg) the following areas have been investigated: (1) Improvement of melting and casting techniques for ingot by introducing atmospheric modifications, vacuum and rotary degassing, and deslagging. (2) The effect of heat treatment on mechanical properties (3) Mechanical characterization by tensile test, fracture toughness test and fatigue crack propagation test. High mechanical properties were found to be intimately related with ingot soundness. Tensile strength of final products varied from 534MPa to 566MPa in peak aged condition while elongation/ductility ranged from 9.0% to 11.9%. From the fracture toughness test with using compact tensile specimen, plane strain fracture toughness($K_{Ic}$) appeared to be 39MPa${\surd}$m in peak aged condition and 23MPa${\surd}$ m in underaged condition. When load ratios of 0.1, 0.3 and 0.5 were given ${\Delta}K_{th}$ was 6.0MPa${\surd}$ m, 5.3MPa${\surd}$ m and 4.3MPa${\surd}$ m respectively.

• Applied Chemistry for Engineering
• /
• v.33 no.2
• /
• pp.195-201
• /
• 2022

The main objective of this work is to prepare Rehmannia glutinosa extract (RE) incorporated functional chitosan (CH) based biomaterials and evaluate their physical properties, RE release properties, inhibitory effect of melanogenesis, and antioxidant and elastase inhibitory activities. RE incorporated CH based biomaterials were synthesized by a casting method and UV curing process. The surface and cross sections of prepared biomaterials were characterized by a field emission scanning electron microscope (FE-SEM). The physical properties such as tensile strength and elongation at break were also investigated. To apply the transdermal drug delivery system, RE release properties were examined with pH 4.5, 5.5, and 6.5 buffer solutions and artificial skin test at 36.5 ℃. Results indicated that RE release of RE incorporated biomaterials with/without the addition of plasticizers [glycerol (GL) and citric acid (CA)] at pH 6.5 was about 1.10 times higher than that of at pH 4.5. In addition, results of the artificial skin test verified that RE was released constantly for 6 h. To verify the applicability of the prepared biomaterials, tyrosinase, 2,2-diphenyl-1-picrylhydrazyl (DPPH), and elastase assays were investigated. Results indicated that RE incorporated biomaterials added CA exhibited tyrosinase activation, DPPH radical scavenging activity rate, and elastase activation of 45.12, 89.40, and 59.94%, respectively.

• Composites Research
• /
• v.36 no.6
• /
• pp.435-440
• /
• 2023

This study aimed to enhance the thermal conductivity of B₄C/Al composite materials, commonly used in transport/storage containers for spent nuclear fuel, by incorporating both boron carbide (B₄C) and cubic boron nitride(cBN) as reinforcing agents in an aluminum (Al) matrix. The composite materials were successfully manufactured through a stir casting process and practical neutron-absorbing materials were obtained by rolling the fabricated composite ingot. The evaluation of the thermal conductivity of the fabricated composites was carried out because thermal conductivity is critical for neutron absorbing materials. The thermal conductivity measurement results indicated an approximately 3% increase in thermal conductivity under the same volume fraction when compared to composite materials using only B₄C particles. Through neutron absorption cross-sectional area calculations, it was confirmed that the neutron absorption capability decreased to a negligible level. Based on the findings of this study, new design approaches for neutron absorption materials are proposed, contributing to the development of high-performance transport/storage containers.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.21 no.6
• /
• pp.1-9
• /
• 2020

The manufacturing processes of high-precision parts for PGM (Precision Guided Missiles) have not been improved for decades; they still depend on machining or high-precision casting. These processes have an advantage when making small amounts of high-reliability parts in the usual case of a PGM system. In the case of a PGM system, however, which has been made for striking an extensive area, requires hundreds of bomblet units that require mass productivity. In addition, in the case of a part that is very difficult to machine, mass productivity and quality cannot be satisfied at the same time. In particular, cost reduction is an essential precondition to strengthening the export competitiveness of Korean defense articles. This study examined whether the MIM process is appropriate for manufacturing high-precision parts that require mass productivity. The optimized MIM process condition was determined after carrying out fundamental research. Comparisons of the quality of prototype parts with original parts and a functional test of a fuse that had been made with MIM parts highlighted the application possibility of the MIM process.

• Korean Journal of Heritage: History & Science
• /
• v.57 no.1
• /
• pp.146-159
• /
• 2024

In this study, a study on the production technology of the Buddha statue and the production of raw material origin was conducted through scientific analysis on the Bronze seated Bodhisattva Statue of Goseongsa Temple, a treasure. As a result of microstructure analysis through a metal microscope, it was confirmed that the microstructure of the Bronze seated Bodhisattva Statue of Goseongsa Temple was a process-type dendritic structure, and the casting structure of bronze was well represented, so it was manufactured through casting. Subsequently, as a result of analyzing the alloy composition ratio through SEM-EDS, it was identified as a ternary alloy with 81.26 wt% of copper (Cu) and 16.42 wt% of tin (Sn) and 1.72 wt% of lead (Pb). The results of the analysis of lead isotope ratios using a thermal ionization mass spectrometer (TIMS) were substituted into the distribution of lead isotope ratios on the Korean Peninsula, it was shown in corresponding to Jeolla-do and Chungcheong-do regions and North and South Gyeongsang Province. This suggests that the raw materials used in their production were likely sourced from the mines around Goseong Temple in Gangjin. Despite the fact that the statue is a medium and large Buddha with a total height of 51 centimeters, 1.72 wt% of lead (Pb) was found as a result of alloy composition ratio analysis, which showed a similar composition to the lead content ratio of small bronze and gilt-bronze Buddha statues. Therefore, we compared and analyzed the results of the analysis of the composition ratio of the alloys of bronze and gilt bronze statues, which has been scientifically analyzed with a compositional age similar to that of the Bronze seated Bodhisattva Statue of Goseongsa Temple. Comparison results, Various factors, such as the size of the Buddha statue as well as its stylistic characteristics and the age of composition, may exist in determining the alloy composition ratio of the bronze and gilt bronze Buddha statues, and it was confirmed that the alloy composition ratio or casting technology was properly adjusted when the Buddha statue was created. In other words, it is judged that a more comprehensive system of Buddha statue production technology should be investigated by conducting archaeological and art history studies on stylistic characteristics and age of composition, as well as scientific analysis results such as observation of internal structure, microstructure observation, and analysis of alloy composition ratio using radiation transmission irradiation.

• Journal of the Korea Concrete Institute
• /
• v.20 no.1
• /
• pp.67-75
• /
• 2008

An engineered cementitious composite produced with slag particles (Slag-ECC) had been developed based on micromechanical principle. Base grain ingredients were properly selected, and then the mixture proportion was optimized to be capable of achieving robust tensile ductility in the hardened state. The rheological design is performed in the present study by optimizing the amount of admixtures suitable for self-consolidating casting and shotcreting process in the fresh state. A special focus is placed on the rheological control which is directly applicable to the construction in field, using prepackaged product with all pulverized ingredients. To control the rheological properties of the composite, which possesses different fluid properties to facilitate two types of processing (i.e., self-consolidating and shotcreting processing), the viscosity change of the cement paste suspensions over time was initially investigated, and then the proper dosage of the admixtures in the cement paste was selected. The two types of mixture proportion were then optimized by self-consolidating & shotcreting tests. A series of self-consolidating and shotcreting tests demonstrated excellent self-consolidation property and sprayability of the Slag-ECC. The rheological properties altered through this approach were revealed to be effective in obtaining Slag-ECC hardened properties, represented by pseudo strain-hardening behavior in uniaxial tension, allowing the readily achievement of the desired function of the fresh Slag-ECC. These ductile composites with self-consolidating and shotcreting processing can be broadly utilized for a variety of applications, e.g., in strengthening seismic resistant structures with congested reinforcements, or in repairing deteriorated infrastructures by shotcreting process.