• 멤브레인
• /
• 제23권5호
• /
• pp.375-383
• /
• 2013

나노 소재는 표면적이 매우 크고 크기나 기공이 균일하여 분리막에서 물질 전달통로나 특수한 기능성을 갖게 하는 소재로 이용이 가능하다. 그중에서도, 그래핀, 그래핀 옥사이드 및 탄소나노튜브와 같은 나노탄소 구조체에 대한 연구가 활발히 이루어지고 있다. 일차원 구조를 갖는 탄소나노튜브의 경우 우수한 열적, 화학적 및 기계적 성질을 가지고 있으나, 기존 연구에서는 주로 고분자와 혼합하여 기계적 물성을 강화하는 복합소재로서 사용됐으며, 응용분야의 한계를 가지고 있었다. 본 연구에서는 폴리 에틸렌 글리콜 다이아크릴레이트(PEGDA) 고분자 내에 개질된 탄소나노튜브를 혼합하여, 기체 분리막에서의 투과도 및 선택도의 변화를 관찰하였다.

• Journal of Korean Vacuum Science & Technology
• /
• 제4권2호
• /
• pp.55-60
• /
• 2000

Vertically aligned carbon nanotubes on nickel coated glass substrates were obtained at low temperatures below 600$\^{C}$ by plasma enhanced hot filament chemical vapor deposition where acetylene gas was used as the carbon source and ammonia gas was used as the dilution gas and catalyst. The diameters of the nanotubes decreased from 96 m to 41 m as NH$_3$/C$_2$H$_2$ ratio increased from 2:1 to 5:1. Total flow rate of input gases with constant NH$_3$/C$_2$H$_2$ ratio did not change the diameter of carbon nanotubes. No growth of the carbon nanotubes was observed with only C$_2$H$_2$ nor N$_2$ instead of NH$_2$. G line and D line in Raman spectra were observed, which implies that there were many structural defects in carbon nanotubes.

• Bulletin of the Korean Chemical Society
• /
• 제28권7호
• /
• pp.1119-1126
• /
• 2007

Hydrogen gas and carbon nanotubes along with nanocarbon were produced from commercial natural gas using fixed bed catalyst reactor system. The maximum amount of carbon (491 g/g of catalyst) formation was achieved on 25% Ni, 3% Cu supported catalyst without formation of CO/CO2. Pure carbon nanotubes with length of 308 nm having balloon and horn type shapes were also formed at 673 K. Three sets of catalysts were prepared by varying the concentration of Ni in the first set, Cu concentration in the second set and doping with K in the third set to investigate the effect on stabilization of the catalyst and production of carbon nanotubes and hydrogen by copper and potassium doping. Particle size analysis revealed that most of the catalyst particles are in the range of 20-35 nm. All the catalysts were characterized using powder XRD, SEM/EDX, TPR, CHN, BET and CO-chemisorption. These studies indicate that surface geometry is modified electronically with the formation of different Ni, Cu and K phases, consequently, increasing the surface reactivity of the catalyst and in turn the Carbon nanotubes/H2 production. The addition of Cu and K enhances the catalyst dispersion with the increase in Ni loadings and maximum dispersion is achieved on 25% Ni: 3% Cu/Al catalyst. Clearly, the effect of particle size coupled with specific surface geometry on the production of hydrogen gas and carbon nanotubes prevails. Addition of K increases the catalyst stability with decrease in carbon formation, due to its interaction with Cu and Ni, masking Ni and Ni:Cu active sites.

• 한국분말재료학회지
• /
• 제24권4호
• /
• pp.275-278
• /
• 2017

In the present work, we apply a technique that has been used for the expansion of graphite to multiwall carbon nanotubes (MWCNT). The nanotubes are rapidly heated for a short duration, followed by immersion in acid solution, so that they undergo expansion. The diameter of the expanded CNTs is 5-10 times larger than that of the as-received nanotubes. This results in considerable swelling of the CNTs and opening of the tube tips, which may facilitate the accessibility of lithium ions into the inner holes and the interstices between the nanotube walls. The Li-ion storage capacity of the expanded nanotubes is measured by using the material as an anode in Li-ion cells. The result show that the discharge capacity of the expanded nanotubes in the first cycle is as high as 2,160 mAh/g, which is about 28% higher than that of the un-treated MWCNT anode. However, the charge/discharge capacity quickly drops in subsequent cycles and finally reaches equilibrium values of ~370 mAh/g. This is possibly due to the destruction of the lattice structures by repeated intercalation of Li ions.

• 반도체디스플레이기술학회지
• /
• 제8권4호
• /
• pp.21-24
• /
• 2009

We investigated a nanoscale inertia sensor based on telescoping carbon nanotubes, using classical molecular dynamics simulations. The position of the telescoping nanotubes is controlled by the centrifugal force exerted by the rotation platform, thus, position shifts are determined by the capacitance between carbon nanotubes and the electrode, and the operating frequency of the carbon nanotube oscillator. This measurement system, tracking oscillations of the carbon nanotube oscillator, can be used as the sensor for numerous types of devices, such as motion detectors, accelerometers and acoustic sensors.

• Tribology and Lubricants
• /
• 제21권6호
• /
• pp.263-267
• /
• 2005

The tribological performance of multi-walled carbon nanotubes (MWNT) in mineral oils is investigated at ambient temperature. The frictional forces, wear amounts and cycles to scuffing of the oils with nanotubes and without those were measured using the ball-on-disk tester. It was found that there were little differences in the frictional forces and wear amounts of two oils. However, the scuffing times of oils with nanotubes were much longer than those of oils without nanotubes in sliding tests. The nanotubes were very effective on maintaining the oil gap and protecting the surfaces in boundary lubricated sliding.

• 한국정보디스플레이학회:학술대회논문집
• /
• 한국정보디스플레이학회 2002년도 International Meeting on Information Display
• /
• pp.666-669
• /
• 2002

Vertically aligned carbon nanotubes (CNTs) have been produced using various type of plasma enhanced chemical vapor deposition (PECVD). Catalysts such as Ni, Co, and Fe are used for growth of CNTs. To explain the effect of catalysts on the growth characteristics of CNTs, carbon species of $C_2H_2$ was observed in different catalysts using optical emission spectroscopy (OES) with theoretical calculation on the surface reaction in different catalysts.

• 한국정보디스플레이학회:학술대회논문집
• /
• 한국정보디스플레이학회 2007년도 7th International Meeting on Information Display 제7권1호
• /
• pp.772-774
• /
• 2007

The improvement in the field emission parameters, luminescent uniformity, degradation rate and half life has been observed for the thin-multi wall carbon nanotube (t-MWCNT) composite, after incorporating the Zn nanoparticles. The Zn nanoparticles $(diameter\;{\sim}\;100\;{\pm}15\;nm)$ has been incorporated to synthesize the Zn-t-MWCNT composite.

• 한국복합재료학회:학술대회논문집
• /
• 한국복합재료학회 2003년도 추계학술발표대회 논문집
• /
• pp.25-28
• /
• 2003

Carbon nanotubes(CNTs), since their first discovery, have been considered as new promising materials in various fields of applications including field emission displays, memory devices, electrodes, NEMS constituents, hydrogen storages and reinforcements in composites due to their extra-ordinary properties. The carbon nanotube reinforced nanocomposites have attracted attention owing to their outstanding mechanical and electrical properties and are expected to overcome the limit of conventional materials. Various application areas are possible for carbon nanotube reinforced nanocomposites through the functionalization of carbon nanotubes. Carbon nanotube reinforced polymer matrix nanocomposites have been fabricated by liquid phase process including surface functionalization and dispersion of CNTs within organic solvent. In case of carbon nanotube reinforced polymer matrix nanocomposites, the mechanical strength and electrical conducting can be improved by more than an order of magnitude. The carbon nanotube reinforced polymer matrix nanocomposites can be applied to high strength polymers, conductive polymers, optical limiters and EMI materials. In spite of successful development of carbon nanotube reinforced polymer matrix nanocomposites, the researches on carbon nanotube reinforced inorganic matrix nanocomposites show limitations due to a difficulty in homogeneous distribution of carbon nanotubes within inorganic matrix. Therefore, the enhancement of carbon nanotube reinforced inorganic nanocomposites is under investigation to maximize the excellent properties of carbon nanotubes. To overcome the current limitations, novel processes, including intensive milling process, sol-gel process, in-situ process and spark plasma sintering of nanocomposite powders are being investigated. In this presentation, current research status on carbon nanotube reinforced nanocomposites with various matrices are reviewed.

• 공업화학
• /
• 제18권1호
• /
• pp.94-97
• /
• 2007

대기압 조건에서 고정층 상압 유통식 반응기를 사용하여 Pd(5)/SPK 촉매상에서 산소의 몰 비 변화에 따른 메탄의 열분해 반응으로부터 탄소 나노튜브 및 탄소 나노선을 제조하였으며, SEM과 TEM을 이용하여 분석하였다. $CH_4/O_2$의 몰 비가 1인 경우, 촉매층 지지대 표면상에 탄소가 거의 침적되지 않았으나, $CH_4/O_2$의 몰 비가 2인 경우에는 촉매층 지지대 표면상에 반응기를 봉쇄할 정도로 다량의 탄소가 침적되었다. 침적된 탄소를 SEM과 TEM을 통하여 분석한 결과 많은 수의 단일 벽 탄소 나노튜브와 탄소 나노선들이 만들어졌음을 확인할 수 있었다. 촉매 표면상에 침적된 탄소 나노튜브의 생성 메카니즘은 첨단성장방식이었고, 촉매 지지대 표면상에 만들어진 탄소 나노튜브 및 나노선들의 생성은 일정한 탄소 성장속도 벡터와 탄소 나노선의 링구조의 핵형성이 중요한 역할을 하였다. SPK 촉매 담체는 열 안정성이 우수하였으며, $N_2$ 흡착등온선은 중기공 세공이 잘 발달된 IV형이었다.