• Korean Chemical Engineering Research
• /
• v.55 no.2
• /
• pp.258-263
• /
• 2017

In this study, we synthesized biocatalyst consisting of glucose oxidase (GOx), polyethyleneimine (PEI) and carbon nanotube (CNT) with addition of p-benzoquinone (BQ) that was considered anodic catalysts of enzymatic biofuel cell (EBC). For doing this, PEI/CNT supporter was bonded with BQ by physical entrapping method stemmed from electrostatic attractive force ([BQ/PEI]/CNT). In turn, GOx moiety was further immobilized on the [BQ/PEI]/CNT to form GOx/[BQ/PEI]/CNT catalyst. This catalyst has a special advantage in that the BQ that has been usually dissolved into electrolyte was immobilized on supporter. According to the electrochemical analysis, maximum current density of the GOx/[BQ/PEI]/CNT catalyst was 1.9 fold better than that of the catalyst that did not entrap BQ with the value of $34.16{\mu}A/cm^2$, verifying that catalytic activity of the catalyst was enhanced by adoption of BQ. Also, when it was used as anodic catalyst of the EBC, its maximum power density was 1.2 fold better than that of EBC using the catalyst that did not entrap BQ with the value of $0.91mW/cm^2$. Based on such results, it turned out that the GOx/[BQ/PEI]/CNT catalyst was promising and viable as anodic catalyst of EBC.

• Clean Technology
• /
• v.5 no.2
• /
• pp.63-68
• /
• 1999

The activities of Ni(20wt%)/$La_2O_3$, Ni(20wt%)/${\gamma}-Al_2O_3$, and Ni(20wt%)/$SiO_2$ catalyst for $CO_2$ reforming of $CH_4$ were investigated in a fixed bed flow reactor under atmospheric condition. Catalyst characterization using XRD, TEM, SEM, BET analysis were also conducted. The catalytic activity of Ni(20wt%)/$La_2O_3$ catalyst has relatively superior to that of Ni(20wt%)/${\gamma}-Al_2O_3$ and Ni(20wt%)/$SiO_2$ catalyst. The good activity of Ni(20wt%)/$La_2O_3$ catalyst seems to depend on reduced $Ni^{\circ}$ phases of NiO($\rightarrow$ Ni + O), $LaNiO_3$($\rightarrow$ $Ni+La_2O_3$), Ni crystalline phases, and decoration of Ni phases by lanthanum species is also an important factor. Ni(20wt%)/${\gamma}-Al_2O_3$ and Ni(20wt%)/$SiO_2$ catalyst due to surface acidity resulted in the deposition of wisker type and encapsulate carbon on the surface of catalyst, but Ni(20wt%)/$La_2O_3$ catalyst did not show carbon on the surface of catalyst up to 8.5hr reaction.

• Journal of Korean Society of Environmental Engineers
• /
• v.33 no.1
• /
• pp.39-46
• /
• 2011

NO oxidation is an important prerequisite step to assist the selective catalytic reduction (SCR) at low temperatures ($<200^{\circ}C$). Therefore, we conducted the lab- and bench-scales experiments appling the sodium chlorite powder ($NaClO_2(s)$) for the oxidation of NO to $NO_2$ and the carbon-based catalyst for the reduction of $NO_x$ and $SO_2$; the lab- and bench-scales experiments were conducted in laboratory and iron-ore sintering plant, respectively. In the lab-scale experiment, known concentrations of $NO_x$ (200 ppm), $SO_2$ (75 ppm), $H_2O$ (10%) and $NH_3$ (400 ppm) in 2.6 L/min were introduced into a packed-bed reactor containing $NaClO_2(s)$, then gases produced by the reaction with $NaClO_2(s)$ were fed into the carbon-based catalyst (space velocity = $2,000hr^{-1}$) at $130^{\circ}C$. In the bench-scale experiment, flue gases of $50Nm^3/hr$ containing 120 ppm NO and 150 ppm $SO_2$ were taken out from the duct of iron-ore sintering plant, then introduced into the flow reactor; $NaClO_2(s)$ were injected into the flow reactor using a screw feeder. Gases produced by the reaction with $NaClO_2(s)$ were introduced into the carbon-based catalyst (space velocity = $1,000hr^{-1}$). Results have shown that, in both lab- and bench-scales experiments, NO was oxidized to $NO_2$ by $NaClO_2(s)$. In addition, above 90% of $NO_x$ and $SO_2$ removal were obtained at the carbon-based catalyst. These results lead us to suggest that the combination of $NaClO_2(s)$ with the carbon-based catalyst has the potential to achieve the simultaneous removal of $NO_x$ and $SO_2$ at low temperature ($<200^{\circ}C$).

• Transactions of the Korean hydrogen and new energy society
• /
• v.17 no.2
• /
• pp.166-173
• /
• 2006

Catalytic reforming of $CO_2$ by $CH_4$ over Ni-YSZ based catalysts was investigated to produce syngas as raw material of high valued chemicals and develop high performance catalyst electrode for an internal reforming of $CO_2$ in SOFC system. Ni-YSZ based catalysts were prepared using physical mixing and maleic acid methods to improve catalytic activity and inhibition of carbon deposition. The catalysts before and after the reaction were characterized by $N_2$ physisorption, TPR(temperature programed reduction), XRD and impedance analyzer. The conversions for $CO_2$ and $CH_4$ over Ni-MgO catalyst showed 90% but much amount of carbon deposition was detected on catalyst surface. On the other hand, the conversions for $CO_2$ and $CH_4$ over NiO-YSZ-$CeO_2$ catalyst showed 100% and 85% respectively, and carbon deposition on catalyst surface was inhibited under the tested condition. It was concluded that NiO-YSZ-$CeO_2$ catalyst is a promising candidate for the catalytic reforming of $CO_2$ and the internal reforming in SOFC system.

• Carbon letters
• /
• v.4 no.2
• /
• pp.57-63
• /
• 2003

In polymer precursor based activated carbon, the structure of starting material is likely to have profound effect on the surface properties of end product. To investigate this aspect phenolic resins of different types were prepared using phenol, mcresol and formaldehyde as reactants and $Et_3N$ and $NH_4OH$ as catalyst. Out of these resins two resol resins PFR1 and CFR1 (prepared in excess of formaldehyde using $Et_3N$ as catalyst in the basic pH range) were used as raw materials for the preparation of activated carbons by both chemical and physical activation methods. In chemical activation process both the resins gave activated carbons with high surface areas i.e. 2384 and 2895 $m^2/g$, but pore size distribution in PFR1 resin calculated from Horvath-Kawazoe method, contributes mainly in micropore range i.e. 84.1~88.7 volume percent of pores was covered by micropores. Whereas CFR1 resin when activated with KOH for 2h time, a considerable amount (32.8%) of mesopores was introduced in activated carbon prepared. Physical activation with $CO_2$ leads to the formation of activated carbon with a wide range of surface area (503~1119 $m^2/g$) with both of these resins. The maximum pore volume percentage was obtained in 3-20 ${\AA}$ region by physical activation method.

• Carbon letters
• /
• v.18
• /
• pp.80-83
• /
• 2016

• Journal of the Korean Institute of Gas
• /
• v.22 no.1
• /
• pp.26-36
• /
• 2018

Conventional nickel-based catalyst processes used for dry reforming reactions have high activation temperatures and problems such as carbon deposition and metal sintering on the active sites of the catalyst surface. In this study, the characteristics of butane dry reforming reaction were investigated by using DBD plasma combined with catalytic process and compared with existing catalyst alone process. The physical and chemical properties of the catalysts were investigated using a surface area & pore size analyzer, XRD, SEM and TEM. Using $10%Ni/{\gamma}-Al_2O_3$ at $580^{\circ}C$, in the case of the catalyst+plasma process, the conversion of carbon dioxide and butane were improved by about 30% than catalyst alone process. When the catalyst+plasma process, the conversion of carbon dioxide and butane and the hydrogen production concentration are enhanced by the influence of various active species generated by the plasma. In addition, it was found that the particle size of the catalyst is decreased by the plasma in the reaction process, and the degree of dispersion of the catalyst is increased to improve the efficiency.

• International Journal of Internet, Broadcasting and Communication
• /
• v.7 no.2
• /
• pp.96-104
• /
• 2015

Fischer Tropsch reaction is one of the interesting topic for renewable and clean energy. Polymerization of carbon monoxide or carbon dioxide with hydrogen over metal supported catalyst can produce long chain hydrocarbons. Synthetic liquid hydrocarbons are promising alternative to fossil fuels. This research work has been focused on the synthesis of Fe based catalyst for Fischer Tropsch reaction. Mesoporous silica (MS) support prepared by a precipitation method using two different washing solution, distilled water (DW) and acid in ethanol solution (ET), and different calcination temperature. Then, Fe/MS was prepared by an incipient wetness impregnation method. All of samples were systematically characterized using various physical and chemical techniques. TEM and XRD analysis were used to ensure that the cubic Ia3d mesostructure is stable after calcination. FTIR spectra are useful to ascertain the existence of template in the support. TPR studies were also used to understand the nature of Fe species and their reducibility. The results reveal that washing the support with distilled water and calcination at $550^{\circ}C$ can efficiently remove the triblock copolymer templates. The existence of template in the support affects the textural properties of all catalyst investigated.

• 한국신재생에너지학회:학술대회논문집
• /
• 2006.11a
• /
• pp.443-446
• /
• 2006

Carbon-supported Platinum (Pt) is the potential electro-catalyst material for anodic and cathodic reactions in fuel cell. Catalytic activity of the metal strongly depends on the particle shape, size and distribution of the metal in the porous supportive network. Conventional preparation techniques based on wet impregnation and chemical reduction of the metal precursors often do not provide adequate control of particle size and shape. We have proposed a novel route for preparing nano sized Pt colloidal particles in solution by oxidation of ethylene glycol. These Pt nano particles were deposited on large surface area carbon support. The process of nano Pt colloid formation involves the oxidation of solvent ethylene glycol to mainly glycolic acid and the presence of its anion glycolate depends on the solution pH. In the process of colloidal Pt formation glycolate actsas stabilizer for the Pt colloidal particle and prevents the agglomeration of colloidal Pt particles. These mono disperse Pt particles in carbon support are found uniformly distributed in nearly spherical shape and the size distribution was narrow for both supported and unsupported metals. The average diameter of the Pt nano particle was controlled in the range off to 3 nm by optimizing reaction parameters. Transmission electron microscopy, CV and RRDE experiments were used to compliment the results.

• Korean Chemical Engineering Research
• /
• v.47 no.4
• /
• pp.410-417
• /
• 2009

Carbon dioxide was absorbed into GMA solution in a stirred flat cell using mesoporous catalyst Imidazole-CP-MS41, which was synthesized by CP-MCM41 with imidazole. Experiments were carried out at a batch-type absorber with different conditions, varying reaction temperature, concentration of GMA, solvent but maintaining 50 rpm of agitation speed and 2 g of catalyst. Absorption rate of $CO_2$ was used to obtain the kinetics based on the film theory using zwitterion mechanism with 2 elementary reaction and the kinetics were correlated with the solubility parameter of the solvents.