• Korean Journal of Environmental Biology
• /
• v.22 no.3
• /
• pp.400-404
• /
• 2004

Polycaprolactone (PCL), a synthetic aliphatic polyester, was buried in activated sludge soil for 66 days at $27^\circ{C}$ and $37^\circ{C}$. The morphology of the surface of PCL film degraded by soil microorganisms was observed. Soil microorganisms degrading PCL were isolated and identified. Soil fungi and soil bacteria utilizing PCL as carbon or energy source were identified as Paecilomyces fumosoroseus KH27, Penicillium digitatum KH28, Fusarium solani KH29, Aspergillus sp. KH30 and Ochrobactrum anthropi KH31, respectively. Biodegradation test of PCL by the isolated strains showed that, P. digitatum KH28 exhibited the most PCL degrading activity at $27^\circ{C}$. However, at $37^\circ{C}$ O. anthropi KH31 showed higher degrading activity than the other soil microorganisms tested.

• Journal of the Korean institute of surface engineering
• /
• v.23 no.2
• /
• pp.24-29
• /
• 1990

The TiN filmms were deposited on the stainless steel substrates by BARE techinique in order to investigate the effects of process parameters such as source-to-substate distance (15-35cm), N2 pressure(4$\times$10-10 -1$\times$10-3mb)and bias voltage(O-2000V), on the deposition rate, the concentration ratio [N/Ti] and the surface color of the films. The deposition rate was deduced from the weight measurement, the [N/ti] ratio by ESCA. The deposition rate decreased with a relationship of=40.2/D2 where D was source-to-substrate distance. The effect of the bias voltage and the N2pressure on the deposition rate, however, appeared negligble. The [N/Ti] ratio was in the narrow range of 0.7 tp 0.8 It increased slightly with the N2 partial pressure and deceased with the source-to-substrate distance. It was confired by ESCA that a significant amount of oxygen and carbon was contaminated after deposition in the top surface of TiN films. The surface color of TiN film was changed from light gold yellow to reddish gold yellow with increasing [N/Ti] ratio.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2007.11a
• /
• pp.347-348
• /
• 2007

On-chip micro humidity sensor, using $CN_x$ films for the sensing material, was designed, simulated, and fabricated with Op amp based readout circuit and diode temperature sensors. To compensate the temperature and other gases, two methods were applied. One is wheatstone-bridge with reference FET that eliminates other undesirable chemical species, and the other is a diode temperature sensor to compensate the temperature effect. $CN_x$ film can be a new humidity sensing material, and has a strong potential to adapt to smart sensors or multi-sensors using MEMS or nano-technology. A particular design technology for integration of sensors and systems together was proposed that whole fabrication process could be achieved by a standard CMOS process.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2006.06a
• /
• pp.114-115
• /
• 2006

반도체 기술이 초고집적화 되어감에 따라 공정에서 선폭이 줄어들고, 박막을 다층으로 제조하는 것이 중요하게 되었다. 이와 같은 제조 공정 하에서는 Si 기판과 금속 박막간의 확산이 커다란 문제로 부각되어 왔다. 특히 Cu는 높은 확산성에 의하여 Si 기판과 접합에서 많은 확산에 의한 문제가 발생하게 되며. 또한 선폭이 줄어듦에 따라 고열이 발생하여 실리콘으로 spiking이 발생하게 된다. 이를 방지하기 위하여 우리는 3개의 화합물로 구성된 Tungsten-Carbon-Nitrogen (W-C-N) 확산방지막을 사용하였다. 실험은 물리적 기상 증착법 (PVD)으로 질소비율을 변화하며 확산방지막을 증착하였고, 이를 여러 온도에서 열처리하여 X-ray Diffraction 분석을 하였다.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2005.07a
• /
• pp.615-616
• /
• 2005

Carbon Nanotubes (CNT) on flexible indium tin oxide (ITO) PET films were prepared for dye-sensitized solar cell (DSSC). These CNTs were prepared by spray coating method for various amount of light transparency. Also, Pt counter electrode was prepared by electro deposition method. All $TiO_2$ electrodes were deposited on ITO-PET films by spray coating method. Micro structural images show that CNT counter electrodes prepared by spray-coating have more dense structure with increasing spraying time (0 to 60 seconds). DSSC consisting of $TiO_2$ electrode and CNT counter electrode was fabricated with various amount of light absorption. DSSC have higher light energy conversion efficiency with increasing the thickness of CNT counter electrode. CNT counter electrode is at least compatible to that of CNT counter electrode.

• Journal of Power System Engineering
• /
• v.18 no.6
• /
• pp.58-63
• /
• 2014

This paper deals with the effects of counterpart materials on the wear behavior of thermally sprayed STS316 coatings. STS316 powders were flame-sprayed onto a carbon steel substrate. Dry sliding wear tests were performed using the applied loads of 15 N. AISI52100, $Al_2O_3$, $ZrO_2$ and $Si_3N_4$ balls were used as counterpart materials. Wear behavior of STS316 coatings against different counterpart materials were studied using a scanning electron microscope(SEM) and energy dispersive X-ray spectroscopy (EDS). The results show that the wear behavior of thermally sprayed STS316 coatings strongly depends on the type of counterpart material. Dominant wear mechanism was similar for all studied materials as failure of adhesion film except for Si3N4 used as counterpart material. In the case of Si3N4 used as counterpart material, dominant wear mechanism was abrasion.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2010.02a
• /
• pp.414-414
• /
• 2010

KSTAR vacuum vessel has been boronized by carborane ($C_2B_{10}H_{12}$) to reduce various kinds of impurities including carbon and oxygen from the wall, since carborane is solid, non-toxic, non-explosive and is easily evaporated, while diborane ($B_2D_6$) is toxic and explosive. To find the best wall condition for the removal of contaminants before application to KSTAR, various amounts (0.3g, 0.5g, 1g) of carborane are tested in a test chamber, where filament discharge was generated in the mixture of helium and carborane with the same KSTAR target pressure (~ 5 mTorr) from base pressure (${\sim}10^-7\;Torr$). Discharge is performed by a pulse sequence mode with 3 second power on and 5 second power off. Deposited films of a-C/B:H are characterized by ellipsometery, AES and XPS, and are compared with those of KSTAR.

• Korean Journal of Organic Agriculture
• /
• v.19 no.spc
• /
• pp.218-221
• /
• 2011

To improve the soil properties of physical and microbial community rice bran and wood charcoal were applied in the continuously cultivated plastic film house soil. Soil physical properties were improved by application of rice bran and charcoal compared to chemical fertilizer application (control) by 8~14% in bulk density and 5~9% in soil porosity. Changes in the biological ratio indexes of fatty acids in the soils were detected depending on the inputted materials. Especially in application of rice bran including mixture with charcoal, much more fungi and less bacteria were detected and the ratio of fungi to bacteria was increased, suggesting the more organic carbon metabolically active in these treatments. The high ratio of aerobe to anaerobe suggested the better aerobic conditions were in the soil inputted wood charcoal. From these results, it is important and possible to select some materials for the organic pepper cultivation, which may improve the poor condition soil.

• Journal of the Korean institute of surface engineering
• /
• v.31 no.3
• /
• pp.142-150
• /
• 1998

Stainless steel is being used widely for various purposes due to its good corrosion resistance. There has been much research to produce colored stainless steel by several methods such as anodizing and ion plating. In this experiment, we coated TiN(C,O,H)films SUS304 substraate with the DC magnetron spttering system made by Leybold Heraeus and studied the interlater structure and abhesive strength of the films as a function of additional gases, acetylene, hydrogen and oxygen. When the acetylene gas was added into the chamber, the specimen with the interlayer phase had good adhesion due to the toughness of the $\gamma'-Fe_4N$ plase induced from a solid solution of carbon atoms, while low adhesion appeared on the specimen of the non interlayer phase. The formation of the interlayer phase($\gamma'-Fe_4N$) was due to hydrogen embrittlement and internal stress induced by $\gamma'-Fe_4N$ formation in the interlayer. We could fine the interlayer phase ($\gamma'-Fe_4N$) at the interface between the film and the substrate of the TEM image when $\gamma'-Fe_4N$ was detected by the X-ray duffraction metheod.

• Journal of the Korean institute of surface engineering
• /
• v.48 no.5
• /
• pp.218-226
• /
• 2015

The goal of this study is to investigate a metal cladding that contains SiC composites as a protective layer and analysis the characteristics of the specimens on high temperature oxidation To make SiC composites, the current process needs a high temperature (about $1100^{\circ}C$) for the infiltration of fixing materials such as SiC. To improve this situation, we need a low temperature process. In this study, we developed a low temperature process for making SiC composites on the metal layer, and we have made two kinds: cladding with protective SiC composites made by polycarbosilane(PCS), and a PCS filling method using supercritical carbon dioxide. A corrosion test at $1200^{\circ}C$ in a mixed steam and Ar atmosphere was performed on these specimens. The result show that the cladding with protective SiC composites have excellent oxidation suprression rates. This study can be said to have developed new metal cladding with enhanced durability by using SiC composite as protective films of metal cladding instead of simple coating film.