• 전기화학회지
• /
• 제15권2호
• /
• pp.101-108
• /
• 2012

본 연구에서는 탄소를 첨가하여 $Li_3V_2(PO_4){_3}$의 낮은 전기전도도를 개선시켜서 고율 방전특성, 충 방전 사이클 특성을 향상시키는 것을 목적으로 하고 있다. 탄소 첨가제로는 글루코스와 CNT (carbon nano tube)를 사용하였으며, 탄소의 첨가 여부와 탄소 원료의 종류에 따라 합성된 $Li_3V_2(PO_4){_3}$의 구조적 그리고 전기화학적 특성에 대해 연구를 하였다. $Li_3V_2(PO_4){_3}$와 $Li_3V_2(PO_4){_3}$/C의 $Li_3V_2(PO_4){_3}$/CNT의 합성방법으로는 고상법을 이용하였다. 합성된 물질을 수소환원방법을 통하여 600, 700, 800, $900^{\circ}C$에서 소성해주었다. 합성된 물질로 양극 집전판을 제작하여 상대전극을 리튬메탈로 한 Coin 2032 cell을 만들어 전기화학적 특성분석을 진행하였다. 전지테스트는 정전류법을 이용하여 3.0~4.8 V까지 충 방전 실험을 하였다.

• 한국철도학회:학술대회논문집
• /
• 한국철도학회 2009년도 춘계학술대회 논문집
• /
• pp.574-580
• /
• 2009

This study is investigate the bending behavior of real size RC beams strengthened with carbon fiber sheets. For experimental study, 1 control beam and 8 strengthened beams of real size(4 NU-beams and 4 U-beams) are tested and compared. NU-beam has not a V-shaped band and V-beam has a V-shaped band. The variables of experiment are composed of the number of carbon fiber sheets, the existence of U-shaped band, and four point loading, etc. The experimental results showed that the strengthening system with U-shaped band controls the premature debonding and provides a more ductile failure mode than the strengthening system without V-shaped band. It can be found from the load-deflection curves that as the number of fiber sheets is increased, the maximum strength and the flexural rigidity is increased. For the strengthening method with carbon fiber sheets of the real size RC beams, it is required the finding a solution to the bonding problem.

• 한국동물위생학회지
• /
• 제16권2호
• /
• pp.127-137
• /
• 1993

Carbon tetrachloride ($CCl_4$) has been used to treat a variety of parasitic infection in both large and small animals, including Fasciola hepatica. Recently, we can easily contest with carbon tetrachloride in air, food, water, rain and Industry area etc. and it is using in order to induce liver injury in laboratory. In this study. we investigated activitis of LDH, ALP, AST and ALT and amount of cholesterol, triacylglycerol, glucose and BUN in mice serum exposed to $CCl_4.$ The mice divided Into a Naive control(A), corn oil control(B) and experimental group(C, D). Naive control group(A) was given feed and water only. Corn oil control group(B) was given corn oil 1ml /100g of body weight(B.W). Experimental group(C) was given carbon tetrachloride 1ml /100g B.W. ($CCl_4$： corn oil=1：20(V /V) ), Experimental group(D) was given carbon teterachloride 1ml /100g B.W. ($CCl_4$: corn oil=1：10(V /V) ). The results obtained were summarized as follows : 1) The body weight was declined after the l0th day In mice exposed to carbon tetra-chloride. 2) The total protein level in serum was significantly in mice exposed to carbon tetra-chloride($P{\leq}0.05$). The albumin and A /G ratio was decresed significantly in mice exposed to carbon tetrachloride($P{\leq}0.01$) 3) All of the activity of LDH, AST, ALT and ALP in mice serum exposed to carbon tetra chloride inclosed significantly activity of LDH ($P{\leq}0.05$), inclosed significantly activity of AST($P{\leq}0.05, \;p {\leq}0.01$), inclosed significantly activityof ALT 3nd ALP($P {\leq}0.05,\;p {\leq}0.01$). 4) The amount of cholesterol and triacylglycerol, lipid metabolite products in serum was inclosed in case of cholesterol but did not change in case of triacylglycerol.

• 전기학회논문지
• /
• 제59권4호
• /
• pp.743-748
• /
• 2010

Boron nitride (BN) and carbon nitride (CN) films, which have relatively low work functions and commonly exhibit negative electron affinity behaviors, were coated on carbon nanotubes (CNTs) by magnetron sputtering. The CNTs were directly grown on metal-tip (tungsten, approximately 500nm in diameter at the summit part) substrates by inductively coupled plasma-chemical vapor deposition (ICP-CVD). The variations in the morphology and microstructure of CNTs due to coating of the BN and CN films were analyzed by field-emission scanning electron microscopy (FE-SEM). The energy dispersive x-ray (EDX) spectroscopy and Raman spectroscopy were used to identify the existence of the coated layers (CN and BN) on CNTs. The electron-emission properties of the BN-coated and CN-coated CNT-emitters were characterized using a high-vacuum field emission measurement system, in terms of their maximum emission currents ($I_{max}$) at 1kV and turn-on voltage ($V_{on}$) for approaching $1{\mu}A$. The results showed that the $I_{max}$ current was significantly increased and the $V_{on}$ voltage were remarkably reduced by the coating of CN or BN films. The measured values of $I_{max}-V_{on}$ were as follows; $176{\mu}A$-500V for the 5nm CN-coated emitter and $289{\mu}A$-540V for the 2nm BN-coated emitter, respectively, while the $I_{max}-V_{on}$ of the as-grown (i.e., uncoated) emitter was $134{\mu}A$-620V. In addition, the CNT emitters coated with thin CN or BN films also showed much better long-term (up to 25h) stability behaviors in electron emission, as compared with the conventional CNT emitter.

• 한국재료학회지
• /
• 제28권3호
• /
• pp.182-188
• /
• 2018

Nitrogen (N)-doped protein-based carbon as platinum (Pt) catalyst supports from tofu for oxygen reduction reactions are synthesized using a carbonization and reduction method. We successfully prepare 5 wt% Pt@N-doped protein-based carbon, 10 wt% Pt@N-doped protein-based carbon, and 20 wt% Pt@N-doped protein-based carbon. The morphology and structure of the samples are characterized by field emission scanning electron microscopy and transmission electron micro scopy, and crystllinities and chemical bonding are identified using X-ray diffraction and X-ray photoelectron spectroscopy. The oxygen reduction reaction are measured using a linear sweep voltammogram and cyclic voltammetry. Among the samples, 10 wt% Pt@N-doped protein-based carbon exhibits exellent electrochemical performance with a high onset potential of 0.62 V, a high $E_{1/2}$ of 0.55 V, and a low ${\Delta}E_{1/2}=0.32mV$. Specifically, as compared to the commercial Pt/C, the 10 wt% Pt@N-doped protein-based carbon had a similar oxygen reduction reaction perfomance and improved electrochemical stability.

• 한국재료학회지
• /
• 제21권9호
• /
• pp.477-481
• /
• 2011

Composites of insulating polyethylene and carbon black are widely used in switching elements, conductive paint, and other applications due to the large gap of resistance value. This research addresses the critical exponent of dielectric breakdown strength of polymer matrix composites (PMC) made with carbon black and polyethylene below the percolation threshold (Pt) for the first time. Here, Pt means the volume fraction of carbon black of which the resistance of the PMC is transferred from its sharp decrease to gradual decrease in accordance with the increase of carbon-black-filled content. First, the Pt is determined based on the critical exponents of resistivity and relative permittivity. Although huge cohesive bodies of carbon black are formed in case of being less than the Pt, a percolation path connecting the conducting phases is not formed. The dielectric breakdown strength (Dbs) of the PMC below Pt is measured by using an impulse voltage in the range from 10 kV to 40 kV to avoid the effect of joule heating. Although the observed Dbs data seems to be well fitted to a straight line with a slope of 0.9 on a double logarithm of (Pt-$V_{CB}$) and Dbs, the least squares method gives a slope of 0.97 for the PMC. It has been found that finite carbon-black clusters play an important role in dielectric breakdown.

• 공업화학
• /
• 제33권3호
• /
• pp.315-321
• /
• 2022

We firstly observed that activated carbon (AC) deposited by atomic-layer vanadium pentoxide (V₂O₅) was used as CDI electrodes to utilize the high dielectric constant for enhancing the capacitance equipped with atomic layer deposition (ALD). It was demonstrated that the vanadium pentoxide (V₂O₅) with sub-nanometer layer was effectively deposited onto activated carbon, and the electric double-layer capacitance of the AC was improved due to an increase in the surface charge density originated from polarization, leading to high ion removal in CDI operation. It was confirmed that the performance of modified-AC increases more than 200%, comparable to that of pristine-AC under 1.5 V at 20 mL min^-1 in CDI measurements.

• 분석과학
• /
• 제8권4호
• /
• pp.477-480
• /
• 1995

Isotopic-spectral method [I] was applicated for determination of carbon in silicate materials (pure silica, guartz glasses, geological probs etc.). Isotopic heterogeneous balancing of carbon in gaseous phase and solid samples was carried out at the temperature of $1500-1900^{\circ}K$. Spectroscopic measuring of isotope concentration in a balanced gas was made using the electron-vibrational band heads of CO molecules excited in HF discharge. Limits of detection of carbon concentrations appear to be $n^*10^{-6}$.

• 열처리공학회지
• /
• 제21권2호
• /
• pp.79-86
• /
• 2008

As a basic research for developing 600 MPa yield strength reinforcing steel bars, the strengthening of 0.25 wt.% carbon steel by vanadium addition was studied. The changes of microstructure and mechanical properties were investigated for the specimen V0 (0.00 wt.% V), V1 (0.03 wt.% V) and V2 (0.06 wt.% V) processed by various heat treatments. To set the heat treatment conditions, the continuous cooling transformation (CCT) curves were drawn for austenitizing temperatures of $900^{\circ}C$ and $1100^{\circ}C$. For specimens tempered at $600^{\circ}C$ after quenching from $900^{\circ}C$ and $1100^{\circ}C$, yield strength was increased by 19 MPa and 21 MPa for 0.01 wt % V addition, and tensile strength was increased by 25 MPa and 28 MPa for 0.01 wt % V addition, respectively. Also, for 0.06 wt.% V added specimens tempered after quenching and normalized, tensile strength was increased by 50 MPa and 30 MPa for increasing austenitizing temperature of $100^{\circ}C$, respectively.

• 한국진공학회:학술대회논문집
• /
• 한국진공학회 2011년도 제41회 하계 정기 학술대회 초록집
• /
• pp.262-263
• /
• 2011

Flexible electronics, a future technology of electronics, require a low cost integrated circuit that can be built on various types of the flexible substrates. As a potential candidate for this application, a single walled carbon nanotube network is studied as an active device with a scheme of thin film transistor. Transistors are formed on a plastic foil by the Roll-to-Roll (R2R) and the Roll-to-Device (R2D) printing method. For both printing methods, electrical transports for the transistors are presented with the temperature dependence of threshold voltage (V_Th) and mobility from the measured transfer curves at temperatures ranging from 10 K to 300 K. It is observed that ${\mu}=0.044cm^2/V{\cdot}sec$ and V_Th=7.28V for R2R and ${\mu}=0.025cm^2/V{\cdot}sec$ and V_Th=3.10V for R2D, both for the temperature at 300K. Temperature dependence of mobility and V_Th is observed. However for R2R, the temperature dependence of V_Th is constant. It is the difference between, R2R and R2D.