• Transactions of the Korean Society of Automotive Engineers
• /
• v.24 no.5
• /
• pp.538-548
• /
• 2016

The purpose of this study is to identify the possibility of effective tuning works, understand the characteristics of tuning engine, and analyse the basic data of engine tuning inspection corresponding to the safe operation and environment of a driving gasoline car. The effects of tuning on the characteristics of performance and exhaust emissions under a wide range of engine speeds are experimentally investigated by the actual driving car with a four-cycle, four-cylinder DOHC, turbo-intercooler, water-cooled gasoline engine operating at four types of non-tuning, tuning 1, 2 and 3. The tuning parts in the gasoline engine are the intake manifold, intake pipe and air filter. In the experiment, the output, torque and air-fuel ratio of the five-speed automatic transmission vehicles were measured at the chassis dynamometer(Dynojet 224xLC) with one person on board. The exhaust emissions of $NO_X$, THC, CO, $O_2$ and $CO_2$, and excess air ratio(${\lambda}$) at the other chassis dynamometer(DASAN-MD-ASM-97-KR-HD) were also measured by the idle/constant-speed mode(ASM2525 mode) test method. It is found that the actual air-fuel ratios of non-tuning and tuning engines were shown to be lower than the stoichiometric air-fuel ratio with increasing engine speed, and the actual air-fuel ratio of non-tuning engine was slightly higher than those of tuning engines when the engine speed is more than 4000 rpm. The output was significantly increased by the tuning whereby the maximum output of tuning engine was more increased to approximately 117.64% than that of non-tuning engine. In addition, CO, THC and $NO_X$ emissions of non-tuning and tuning engines measured by the constant-speed test mode were all satisfied with the inspection standards. CO emission was increased, while THC and $NO_X$ emissions were reduced by tuning.

• Journal of the Korean Society of Marine Environment & Safety
• /
• v.23 no.5
• /
• pp.532-540
• /
• 2017

This paper suggests study of basic structure design and structural analysis for the twin car-ferries. The rules and methodology for the strength analysis of medium and small sized high speed vessels with a length of more than 50m and a length/width ratio of more than 12, such as car-ferries, have not been clarified yet. Therefore, in this paper, the members scantling were carried out using the KR Rule, and the car-ferry exclusive vessel standard were further applied to verify the structural strength the design. The scantling of the members is based on the Korea Classification standards, and the car-ferries standards were additionally applied to verify the structural strength of the design. Especially, the ultimate strength of hull girder was additionally carried out by using car-ferry exclusive vessel standard, and proposed to overcome ambiguity of design by existing standard. The results of this study are expected to be useful as basic data related to structural design and structural analysis of high speed twin-hull car-ferries. The present car-ferry design has a sufficient safety margin in strength point of view according to the KR rule.

• Proceedings of the KIEE Conference
• /
• 2001.07b
• /
• pp.1239-1241
• /
• 2001

This research addresses a new vehicle detecting scheme which uses MR(Megneto Resistive) sensor. A vehicle detector which includes two MR sensors for detecting car presence and speed, sensor voltage amplifiers, signal processor, microprocessor, RF data transceiver and a simple car moving simulator is constructed. From experimental results with the vehicle detector the proposed vehicle detecting scheme was verified.

• Proceedings of the KSR Conference
• /
• 1999.11a
• /
• pp.519-525
• /
• 1999

This paper describes a crashworthy design for the front structure of KHST (Korean High Speed Train) under the SNCF accident scenario (collision against a movable rigid mass of IS tons at 110 km/h). The front structure designed in a new concept shows good behaviours in crashworthy point of view. It collapses in a progressive and well-controlled fashion. To evaluate the design by considering real situations, the power-car is simulated for accidents collided against a dump truck of 15 tons at 110 km/h. The front end structure of it shows a good response on crashworthiness.

• Proceedings of the KSR Conference
• /
• 2005.05a
• /
• pp.467-472
• /
• 2005

The characteristics of dynamic vibration are generally analyzed by an acceleration of a car body of high speed train and the acceleration can be applied to evaluation of running safety. The test of process and the analysis method about it are well explained on UIC Code 518 OR which is the spacial international standard about running safety and dynamic behavior on the line test for railway vehicle. Korean High Speed Train designed to operate at speed 350km/h has been tested on high speed line since it was developed in 2002 and it recorded the highest speed 352.4km/h at the 16th Dec. 2004 in Korea. This paper includes the analysis of running behavior of this train at speed 350km/h and also the analysis of dynamic safety is presented in it, extending to the range of high speed while the UIC 518 limit the speed below 200km/h.

• Journal of Auto-vehicle Safety Association
• /
• v.4 no.2
• /
• pp.5-10
• /
• 2012

Whiplash is the most frequent injury among occupants in low speed rear-end car collision. The aim of this paper is to analyze thecorrelation between influence parameters of head restraints and whiplash injury criteria.In this paper, DFSS (Design for Six Sigma) method is used for optimum design of head restrains. Four control factors of head restraints have selected by function matrix method. The effects of the control factors have been experimentally evaluated by using a sled pulse from 16km/h relative velocity which is suggested by KNCAP (Korean New Car Assessment Program). In order to reduce the noise factors of dynamic tests, whiplash tests were repeated twice. By using DFSS, the correlation between control factors and injury criteria has been comprehended.

• Journal of the Korean Institute of Navigation
• /
• v.24 no.5
• /
• pp.397-403
• /
• 2000

Since very large and high-speed ships have been appeared in marine transportation from 1970s, these ships with poor maneuverability have made large-scale accidents frequently all over the world. The IMO(International Maritime Organization) recommended that ship designers should evaluate various maneuvering performance at initial stage and serve them to ship operators when they deliver a new ship. Meantime, it is expected that ships with large and wide superstructure would have poor maneuverability when they are affected by strong wind. Therefore, car carrier ship with large superstructure was selected to confirm how the ship responds to the external wind forces in this paper. The lateral and transverse projected areas above the water level were considered and ship behaviors were checked by change of rudder angles under severe wind conditions of different directions. In addition, hydrodynamic derivatives and coefficients were predicted from ship particulars and numerical calculations were carried out with the mathematical model of low speed maneuvering motions.

• Journal of Institute of Control, Robotics and Systems
• /
• v.16 no.6
• /
• pp.524-531
• /
• 2010

The automobile networks consist of the communication bus systems which become independent and heterogeneous each other. Most often, the CAN buses are implemented in a car in order to connect all the electronic control units in various ways. Thus, some gateways are necessary for exchanging the useful information between electronic control units on the buses. The automobile body networks group is divided into two kinds on a large scale, namely the low-speed bus and the high-speed bus. To interchange messages between the two, a CAN signal gateway is designed and implemented in a miniature scale. A network analyzer (called "Vehicle spy") and an oscilloscope monitor network situation to confirm the due operation of CAN signal gateway. The efficiency of the designed gateway is evaluated. The more message thread increased, the more efficiency decreased.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2000.06a
• /
• pp.1360-1366
• /
• 2000

KHST project plans to design and to build an high speed train. There are noise requirements in passenger room for the standing and running train, which should be reached. Noise prognosises are calculated for the standing and running TM5(Motorized car) and TT4(Trailer car) train (v=300km/h) to find out critical areas in or around the train. On those areas, actions of noise reduction are proposed to reach the requirements. Finally noise prognosises are calculated for the higher velocity of v=350km/h.

• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.19 no.1
• /
• pp.36-42
• /
• 2020

In this study, flow analyses of a vehicle at driving were carried out after each installation of a tuning part, specifically the bonnet air ducts, the rear spoiler, and the rear diffuser. The study models were designed to comprise a total of eight cases in which each of the three parts were mounted individually or all together in vehicles. Assuming that the vehicle were driven with an average high speed of 100 km/h, the speed and pressure around the vehicle were obtained using CFD when driving. The rear diffuser that becomes the most effective among the three mounting parts has a major role in reducing air resistance.