• Magazine of the Korean Society of Agricultural Engineers
• /
• v.26 no.1
• /
• pp.52-72
• /
• 1984

This study was performed to obtain the basic data which can be applied to the use of epoxy resin mortars. The data was based on the properties of epoxy resin mortars depending upon various mixing ratios to compare those of cement mortar. The resin which was used at this experiment was Epi-Bis type epoxy resin which is extensively being used as concrete structures. In the case of epoxy resin mortar, mixing ratios of resin to fine aggregate were 1: 2, 1: 4, 1: 6, 1: 8, 1:10, 1 :12 and 1:14, but the ratio of cement to fine aggregate in cement mortar was 1 : 2.5. The results obtained are summarized as follows; 1.When the mixing ratio was 1: 6, the highest density was 2.01 g/cm$^3$, being lower than 2.13 g/cm$^3$ of that of cement mortar. 2.According to the water absorption and water permeability test, the watertightness was shown very high at the mixing ratios of 1: 2, 1: 4 and 1: 6. But then the mixing ratio was less than 1 : 6, the watertightness considerably decreased. By this result, it was regarded that optimum mixing ratio of epoxy resin mortar for watertight structures should be richer mixing ratio than 1: 6. 3.The hardening shrinkage was large as the mixing ratio became leaner, but the values were remarkably small as compared with cement mortar. And the influence of dryness and moisture was exerted little at richer mixing ratio than 1: 6, but its effect was obvious at the lean mixing ratio, 1: 8, 1:10,1:12 and 1:14. It was confirmed that the optimum mixing ratio for concrete structures which would be influenced by the repeated dryness and moisture should be rich mixing ratio higher than 1: 6. 4.The compressive, bending and splitting tensile strenghs were observed very high, even the value at the mixing ratio of 1:14 was higher than that of cement mortar. It showed that epoxy resin mortar especially was to have high strength in bending and splitting tensile strength. Also, the initial strength within 24 hours gave rise to high value. Thus it was clear that epoxy resin was rapid hardening material. The multiple regression equations of strength were computed depending on a function of mixing ratios and curing times. 5.The elastic moduli derived from the compressive stress-strain curve were slightly smaller than the value of cement mortar, and the toughness of epoxy resin mortar was larger than that of cement mortar. 6.The impact resistance was strong compared with cement mortar at all mixing ratios. Especially, bending impact strength by the square pillar specimens was higher than the impact resistance of flat specimens or cylinderic specimens. 7.The Brinell hardness was relatively larger than that of cement mortar, but it gradually decreased with the decline of mixing ratio, and Brinell hardness at mixing ratio of 1 :14 was much the same as cement mortar. 8.The abrasion rate of epoxy resin mortar at all mixing ratio, when Losangeles abation testing machine revolved 500 times, was very low. Even mixing ratio of 1 :14 was no more than 31.41%, which was less than critical abrasion rate 40% of coarse aggregate for cement concrete. Consequently, the abrasion rate of epoxy resin mortar was superior to cement mortar, and the relation between abrasion rate and Brinell hardness was highly significant as exponential curve. 9.The highest bond strength of epoxy resin mortar was 12.9 kg/cm$^2$ at the mixing ratio of 1:2. The failure of bonded flat steel specimens occurred on the part of epoxy resin mortar at the mixing ratio of 1: 2 and 1: 4, and that of bonded cement concrete specimens was fond on the part of combained concrete at the mixing ratio of 1 : 2 ,1: 4 and 1: 6. It was confirmed that the optimum mixing ratio for bonding of steel plate, and of cement concrete should be rich mixing ratio above 1 : 4 and 1 : 6 respectively. 10.The variations of color tone by heating began to take place at about 60˚C, and the ultimate change occurred at 120˚C. The compressive, bending and splitting tensile strengths increased with rising temperature up to 80˚ C, but these rapidly decreased when temperature was above 800 C. Accordingly, it was evident that the resistance temperature of epoxy resin mortar was about 80˚C which was generally considered lower than that of the other concrete materials. But it is likely that there is no problem in epoxy resin mortar when used for unnecessary materials of high temperature resistance. The multiple regression equations of strength were computed depending on a function of mixing ratios and heating temperatures. 11.The susceptibility to chemical attack of cement mortar was easily affected by inorganic and organic acid. and that of epoxy resin mortar with mixing ratio of 1: 4 was of great resistance. On the other hand, when mixing ratio was lower than 1 : 8 epoxy resin mortar had very poor resistance, especially being poor resistant to organicacid. Therefore, for the structures requiring chemical resistance optimum mixing of epoxy resin mortar should be rich mixing ratio higher than 1: 4.

• The Korean Journal of Pesticide Science
• /
• v.18 no.3
• /
• pp.202-209
• /
• 2014

RNA interference (RNAi) is the method which controls phenotypes of gene in live cells. Chitinase is the enzyme helping digestion and absorption of old cuticles during the ecdysis of insects. In order to investigate molting-inhibition effect with the chitinase related gene in Spodoptera litura, RNA was extracted from the $5^{th}$ instars. cDNA was synthesized and then we obtained about 700 bp size chitinase. After PCR products were cloned into a pGEM T-easy vector, colonies were picked. DNA was extracted from the colony cultures. EcoR I enzyme was used to check whether PCR products were inserted or not. And then we confirmed vector band of about 3 kb and insert band of about 700 bp. To synthesize the dsRNA, each DNA was cut with Spe I and Nco I enzymes (Circular DNA became lineared DNA). After synthesis of dsRNA, approximately 5 ul dsRNA was injected into the $3^{rd}$ abdominal segment of S. litura $4^{th}$ larvae. The concentration of dsRNA was about $10{\mu}g/{\mu}l$. We confirmed larval-larval molting : there were phenotypically abnormal individuals - for instance malformation, molting inhibition and change of integument color. Pupaadult molting : there were phenotypically abnormal individuals - for instance molting inhibition, change of wings and malformation. Also we could investigate the pupation, emergence and variation about noninjection, treated with DW and dsRNA. Each pupation was non-injection 83.3%, DW 78.3% and dsRNA 66.7%. Each emergence was non-injection 90.0%, DW 72.3% and dsRNA 65.0%. So we considered that chitinase dsRNA induced molting inhibition effect. But each variation was non-injection 8.9%, DW 2.9% and dsRNA 19.2%. Therefore dsRNA group showed the highest variation value. When 18 hours after injecting dsRNA, we could obtain abnormal individual.

• Journal of Korean Society of Environmental Engineers
• /
• v.22 no.4
• /
• pp.765-773
• /
• 2000

The degradation of humic acid using $TiO_2$ coatings was studied, $TiO_2$ coatings were prepared by dip-coating method. Sol solutions for coating were prepared by mixing the gel, which can be produced by the reaction of $TiOCl_2$ and $NH_4OH$ solution, and hydrogen peroxide solution, and hydrolysis of titanium tetraisopropoxide (TTIP). It was shown from XRD that coatings from sol aged at $100^{\circ}C$ for 18h with titanium peroxo solution were crystallized to anatase in the range of temperatures of $25^{\circ}C$ to $500^{\circ}C$. In contrast, those coated from TTIP were crystallized to anatase at temperature above $400^{\circ}C$. So the sols originated from $TiCl_4$ can be applied for not only on the heat-resistance substrates but on the plastic substrates. Thickness and the quality of the films were dependent on the withdrawing speed, the concentration of sol, and the number of coating. The films showed various interference colors depending on the thickness of them. In the case that the films coated 2 times at withdrawing speed of 2.5cm per minute by 0.2M sol, the films had a transparent light blue color with thickness of around 50nm. It was known from the result of photo-degradation by $TiO_2$ coatings using humic acid that the removal efficiency of $COD_{cr}$ was over 85% after illumination of $UV/H_2O_2$ for 40min. and that of UV/VIS absorbable materials was over 95%.

• Korean Journal of Fisheries and Aquatic Sciences
• /
• v.35 no.4
• /
• pp.417-423
• /
• 2002

The edible films were prepared from the protein of alaska pollack, Theragra chalcogrmma. Effects of plasticizer, cross linker and laminated film on physical properties such as tensile strength (TS), elongation (E) and water vapor permeability (WVP) of films were investigated. In adding various kinds of plasticizers, TS of the films prepared with propylene glycol (PG) was the highest, and followed sorbitol, polyethylene glycol 200 (PEG 200) and glycerol. Elongation of the films prepared with glycerol was the highest, then sorbitol, PEG 200 and PG. WVP of films showed lower in order of PG, sorbitol, glycerol and PEG 200.75 decreased with the increment of plasticizer concentration, but elongation increased, The addition of both PG and PEG 200 effected weakly on elongation, so they were inadequate as plasticizer for the film. Mixtures of glycerol and sorbitol, which showed opposing both TS and elongation in the films, could control the physical properties of the films. With increasing relative humidity, TS decreased, while elongation and equilibrium moisture content increased. By adding the cross linkers such as ascorbic acid, citric acid and succinic acid, TS and m of films increased, while elongation decreased. Ascorbic acid, citric acid, succinic acid were most effective for TS at 0.2, 0.1 and $0.1\%, respectively. Laminated film with alaska pollack protein and corn zein improved TS above two times, reduced WVP about $20\~30\%$, as compared with the Elm from alaska pollack protein. Two films did not show the difference to oxygen permeability, but they showed about tenfold greater oxygen resistance than polyethylene film. Laminated film showed higher b and $\Delta$E value of color difference, lower a and L value than the film from alaska pollack protein.

• Korean Journal of Fisheries and Aquatic Sciences
• /
• v.35 no.2
• /
• pp.166-172
• /
• 2002

The top shell, Omphalius pfeifferi capenteri meat vacuum-packed in can (diameter$\times$height, 74.1mm$\times$50.7mm) were heated at 115$^{\circ}C$ up to $F_0$ values of 5 min, 10 min, 15 min and 20 min, and the changes in food components were studied. After 14 days storage at 37$^{\circ}C$ and 55$^{\circ}C$, no growth of microorganism and panelling were recognized from the canned meats which were sterlized at 115$^{\circ}C$ with $F_0$ value of S min and over. In the case of proximate composition of the canned meats, the moisture content decreased with the increase of $F_0$ value, while crude protein increased. The increase of volatile basic nitrogen content, pH and degree of browning and the decrease of mineral, total amino acid, free amino acid, trimethylamine oxide, total creatinine contents and yields were observed during thermal processing, In sensory evaluation on color, texture and taste in the canned meats, no significant difference was observed among a boiled sample and the canned meats heated at re value of 10 min and below. But, in the canned meats heated at $F_0$ value of over 15 min, its sensory scores decreased with the increase of $F_0$ value. From these results, the reasonable $F_0$ value for preparation of the heat-treated top shell meats was in the range of 5$\~$10 min.

• Korean Journal of Fisheries and Aquatic Sciences
• /
• v.17 no.5
• /
• pp.373-382
• /
• 1984

Processing conditions of retort pouched fried mackerel fish meat paste and quality stability during storage were investigated. The reasonable amounts of added ingredients to the frozen mackerel meat paste were $10\%$ of corn starch, $1\%$ of soybean protein, $1.5\%$ of sodium chloride, $0.6\%$ of monosodium glutamate, $0.3\%$ of alcoholic extract of red pepper, and $0.1\%$ of sodium erythorbate as an antioxidant and also added water corresponding to $10\%$ of the frozen mackerel meat paste. After grinding the defrosted mackerel fish meat paste with ingredients, the meat paste was molded in bar type and fried in soybean oil at $170-180^{\circ}C$ for 3 minutes. The fried mackerel meat paste was cooled, vacuum-packed in laminated plastic film bag (polyester/polyvinylidene chloride/unoriented polypropylene : $12{\mu}m/15{\mu}/50{\mu}m,\;14{\times}19cm$) and finally sterilized at $120^{\circ}C$ for 20 minutes in a hot water circulating retort. The pH, volatile basic nitrogen, moisture content, water activity, color, thiobarbituric acid value, peroxide value, texture and viable bacterial count of products were examined during 100 days of storage at $25{\pm}3^{\circ}C\;and\;5^{\circ}C$. The results showed that products could be preserved in good condition for 100 days at $25{\pm}3^{\circ}C$. Judging from sensory evaluation, the quality of products was not inferior to that of market products.

• Journal of the Korean Institute of Traditional Landscape Architecture
• /
• v.37 no.3
• /
• pp.37-48
• /
• 2019

This study, which starting from Yangyang Jukdo's topography formation and questioning revealed in landscape guide and landscape commentary board, is to sort out the characteristics of Jukdo natural landscape through literature research, field observation research and stakeholder interview as part of the proper recognition of Jokdo landscape and search for landscape resources, and pursued a review of nominations and criticism. The results of this study are summarized as follows. Yangyang Jukdo is an island named because it was full of blue bamboo. From before the first half of the 14th Century. to the middle of the 18th Century., there was a Gwanlan-pavilion to see the sea and the bamboo in the west. The time when the original island, the Jukdo, have been a land-tied island connected with the land by the tombolo formed by the erosion of the sand. It is located at the end of the 14th Century. and before the middle of the 18th Century. In Jukdo, colorful weathered terrains, coastal terrain, and structural terrain formed by long-time weathering are found. Among them, the type of weathering, the tafoni style and the gnamma style are the scenic landscapes with the key stories of legend and poetry that are brought to Jukdo. In addition, there are seven kinds of letters caved in the rocks in Jukdo. The rocks found on the coast, basketball cannons, shrines, and sutras are seen as shrouds based on a Taoist hermit motifs and style. In addition, it can be interred from the photography of "jeongssisejeog" that the souvenir of Jukdo was the family of Chogyejeong of mid 18th Century. In terms of observational geography and poetry, Jukdo has been handed down a great deal of missionary color with key motifs such as 'Jukdo-seongoo', 'Jukdo-Dolgooyoo', or 'Stone mortar of Taoist hermit' It is proved that the pearl which is called 'The stone of the Taoist hermit' is a porthole formed in a separate space rather than the topography of the geomorphology in terms of shape, size and function. Currently named Shun-tang is a product of the ridiculous 'naming' of interest. The present landscape guide and commentary is not only incompatible with the place of Jukdo, but also does not match the traditional cultural landscape. Future scenery information such as guide signs and commentary boards should be improved in the direction of positively highlighting the stories and motifs related to the present that are present in order to enhance the landscape identity of Yangyang Jukdo.

• Korean Journal of Food Science and Technology
• /
• v.29 no.3
• /
• pp.502-508
• /
• 1997

Rice bran dietary fiber extract, which was obtained after termamyl treatment of defatted rice bran contained $27.3{\sim}30.5%$ protein, $49.7{\sim}54.1%$ insoluble dietary fiber, and $1.9{\sim}2.7%$ soluble dietary fiber. Extrusion decreased the insoluble dietary fiber content but increased the soluble dietary fiber content, while roasting did not. Influence those content. Each mineral element content was depended upon heat processing method. Extrusion increased the water binding capacity and L value, while roasting reduced the water binding capacity and L value. Scanning electron microscopy showed damaged cell walls for extruded sample compared to roasted one which had fully collapsed cell walls. The increase of water absorption, developing time, and stability and the of MTI of wheat flour-dietary fiber extract composites with addition of dietary fiber extract were observed by Farinograph. Rice bran dietary fiber extract had an effect on the bread making resulting in increase of bread weight and color of crumb and crust, and decrease of bread volume and texture. As a result of sensory evaluation, appearance, texture, overall acceptability were significantly different from control but flavor and taste were not different significantly up to 6% level. Heat treated samples had differences in mean values, but not significant differences statistically.

• Journal of the Korean Society of Food Science and Nutrition
• /
• v.30 no.4
• /
• pp.611-616
• /
• 2001

Effects of high pressure and thermal pasteurization on the survival of microorganisms and quality changes of kochujang during 120 days of storage at 37$^{\circ}C$ were investigated. Viable cell counts were 1.43$\times$10$^{6}$ CFU/g in heat-treated, and 1.56$\times$10$^3$ CFU/g in pressure-treated, and decreased up to 3 log cycle, compared with 3.78$\times$10$^{6}$ CFU/g in the untreated kochujang. Viable cell counts decreased by the storage period at 37$^{\circ}C$. Viable cell counts decreased up to 2 log cycle from 3.78$\times$10$^{6}$ to 5.43$\times$10$^4$ CFU/g in the untreated kochujang, 4 log cycle from 1.43$\times$10$^{6}$ to 3.10$\times$10$^2$ CFU/g in heat-treated after 120 days of storage, while those in pressure-treated were not detected after 90 days from the initial stage of 1.56$\times$10$^3$ CFU/g. pH decreased significantly by the storage time. Titratable acidity increased significantly during storage, and pressure-treated kochujang showed lower values than heat-treated. Amino nitrogen content decreased significantly during storage, and pressure-treated kochujang showed higher values than heat-treated and lower values than the untreated. There were no significant changes in reducing sugar and ethanol content regardless of the treatment condition and the storage period. Hunter L, a and b values decreased significantly during storage. In the untreated kochujang, the changes in color accelerated compared with heat and pressure-treated.

• Journal of the Korean Society of Food Science and Nutrition
• /
• v.34 no.5
• /
• pp.721-728
• /
• 2005

The physicochemical and microbial characteristics of pickled cucumber prepared with dry salting method, which has been used for industry, were investigated. Salting and storage conditions were HSHT $(30\%,\;25^{\circ}C)$, MSMT $(21\%,\;15^{\circ}C)$, MSLT $(21\%,\;0^{\circ}C)$, LSMT $(15\%,\;15^{\circ}C)$ and LSLT $(15\%,\;0^{\circ}C)$. Acidity was lower, and pH was higher in higher salt concentration as well as lower temperature groups. At the storage of 165 days, acidity and pH reached to $0.21\%$ and 4, respectively in MSLT and HSHT, of which conditions fermentation was retarded, compared to the other groups. During storage of pickled cucumber, greenness (-a) of Hunter color system showed the highest in MSLT ranged from -10.70 to -8.08, while in LSMT, the lowest to 1.17. Total microbial and lactic acid bacteria number in HTST and MSLT were the lowest than in other groups, while tile highest in LSMT. Yeast was not detected in HSHT and MSLT after 36 days of storage, while higher in LSMT Texture profile analysis exhibited that fracturability (2,318 g and 2,318 g) and hardness (849 g and 702 g) were highest in HSHT and MSLT, compared to the other groups. Scores of over-all preference for MSLT and LSLT were higher with 8.8 and 7.6, respectively, compared to the other products (p<0.05). Based on these results, lower saltiness and lower storage temperature condition was better for pickled cucumber preparation in industry.