• Journal of the Optical Society of Korea
• /
• 제12권2호
• /
• pp.112-117
• /
• 2008

Single-mode propagation conditions of X-ray waveguides are investigated by numerical calculations in order to understand the importance of waveguide design parameters, such as core thickness and the optical constants of waveguide materials, on the transmission and coherence properties of the waveguide. The simulation code for mode analyzing is developed based on a numerical solution of the parabolic wave equation. The initial boundary value problem is solved numerically using a finite-difference scheme based on the Crank-Nicolson scheme. The E-field intensities in a core layer are calculated at an X-ray energy of 8.0 keV for air and beryllium(Be) core waveguides with different cladding layers such as Pt, Au, W, Ni and Si to determine the dependence on waveguide materials. The highest E-field intensity radiated at the exit of the waveguide is obtained from the Pt cladded beryllium core with a thickness of 20 nm. However, the intensity from the air core waveguide with Pt cladding reaches 64% of the Be-Pt waveguide. The dependence on the core thickness, which is the major parameter used to generate a single mode in the waveguide, is investigated for the air-Pt, and Be-Pt waveguides at an X-ray energy of 8.0 keV. The mode profiles at the exit are shown for the single mode at a thickness of up to 20 nm for the air-Pt and the Be-Pt waveguides.

• ETRI Journal
• /
• 제34권2호
• /
• pp.216-225
• /
• 2012

This paper presents a transceiver module for human body communications whereby a spread signal with a group of 64 Walsh codes is directly transferred through a human body at a chip rate of 32 Mcps. Frequency selective digital transmission moves the signal spectrum over 5 MHz without continuous frequency modulation and increases the immunity to induced interference by the processing gain. A simple receiver structure with no additional analog circuitry for the transmitter has been developed and has a sensitivity of 250 ${\mu}V_{pp}$. The high sensitivity of the receiver makes it possible to communicate between mobile devices using a human body as the transmission medium. It enables half-duplex communication of 2 Mbps within an operating range of up to 170 cm between the ultra-mobile PCs held between fingertips of each hand with a packet error rate of lower than $10^{-6}$. The transceiver module consumes 59 mA with a 3.3 V power supply.

• ETRI Journal
• /
• 제35권4호
• /
• pp.610-616
• /
• 2013

This paper proposes a transparent logic circuit for radio frequency identification (RFID) tags in amorphous indium-gallium-zinc-oxide (a-IGZO) thin-film transistor (TFT) technology. The RFID logic circuit generates 16-bit code programmed in read-only memory. All circuits are implemented in a pseudo-CMOS logic style using transparent a-IGZO TFTs. The transmittance degradation due to the transparent RFID logic chip is 2.5% to 8% in a 300-nm to 800-nm wavelength. The RFID logic chip generates Manchester-encoded 16-bit data with a 3.2-kHz clock frequency and consumes 170 ${\mu}W$ at $V_{DD}=6$ V. It employs 222 transistors and occupies a chip area of 5.85 $mm^2$.

• 천문학회보
• /
• 제37권2호
• /
• pp.139.1-139.1
• /
• 2012

Wilson and Bappu (1957) found a significant relationship (WBR) between the absolute magnitude ($M_v$) and the width of the Ca II K emission line (W) for late type stars. In this study, we revisit the WBR to claim that WBR can be an excellent indicator of stellar surface gravity. We analyze 95 high-resolution spectra of G, K and M type stars obtained with UVES and BOES. WBR found in this work is $M_v$=34.22-18.34logW. In addition, stellar atmospheric parameters ($T_{eff}$, logg, [Fe/H], ${\xi}_{tur}$) are determined with the MOOG code and the Kurucz ATLAS9 model grids for G and K type stars. For M type stars, the method of Belle et al. (1999) is used to derive effective temperature which shows good agreement with other methods. Using the derived $T_{eff}$ and the measured logW,we find the relationship between logg and [logW, logT]; ${\log}g-_{fit}=-25.051-5.527{\log}W+10.254{\log}T_{eff}$. This relation can be applied to estimate the surface gravity of M type stars, which is difficult to be determined by other methods.

• 한국진공학회:학술대회논문집
• /
• 한국진공학회 2013년도 제45회 하계 정기학술대회 초록집
• /
• pp.183.1-183.1
• /
• 2013

70 MeV 사이클로트론의 인젝션 빔 라인은 Multi-CUSP 이온원에서 인출된 H- 빔을 펄스 또는 번칭하여 인플렉터를 통해 사이클로트론의 가속영역인 Dee로 전송하는 역할을 한다. 이 때, 빔을 번칭 시킴으로써 가속효율을 높이고, 손실을 줄여 높은 전류의 빔을 공급할 수 있도록 해야한다. 인젝션 시스템은 einzel lens, chopper, buncher, solenoid 등으로 구성된다. Einzel lens는 빔을 buncher의 중심으로 집속시켜 buncher의 번칭 효율을 높이고, buncher는 전기장을 이용하여 빔을 진행방향으로 집속시키는 기능을 갖는다. Chopper는 번칭된 빔을 일정 주기로 편향을 시켜 펄스 빔의 형태로 전송하는 역할을 한다. 솔레노이드는 적절한 자기장을 이용하여 빔을 집속시켜 인플렉터로 전송한다. 본 연구에서는 사이클로트론의 고전류 인젝션 시스템을 구축하고 각각의 구성요소에서 빔 envelope를 계산하고 비교하였다. SIMION code는 user가 지정한 특성을 가진 개별 입자의 궤도를 추적하는 프로그램으로 인젝션 시스템을 구성하는 각각의 컴포넌트에서의 입자의 진행모습과 buncher를 이용하여 빔의 전송 밀도가 향상됨을 확인하였다. 아울러 TRANSPORT 및 TURTLE 프로그램을 이용하여 SIMION을 통해 계산된 빔의 envelope과 비교하였다.

• Advances in nano research
• /
• 제7권6호
• /
• pp.419-429
• /
• 2019

The effect of an increasing percentage of nanofiller (glass cenosphere) with Glass/Epoxy hybrid composite curved panels modeled mathematically using the multiscale concept and subsequent numerical eigenvalues of different geometrical configurations (cylindrical, spherical, elliptical, hyperboloid and flat) predicted in this research article. The numerical model of Glass/Epoxy/Cenosphere is derived using the higher-order polynomial type of kinematic theory in association with isoparametric finite element technique. The multiscale mathematical model utilized for the customized computer code for the evaluation of the frequency data. The numerical model validation and consistency verified with experimental frequency data and convergence test including the experimental elastic properties. The experimental frequencies of the multiscale nano filler-reinforced composite are recorded through the impact hammer frequency test rig including CDAQ-9178 (National Instruments) and LABVIEW virtual programming. Finally, the nano cenosphere filler percentage and different design associated geometrical parameters on the natural frequency data of hybrid composite structural configurations are illustrated through a series of numerical examples.

• 한국정보통신학회:학술대회논문집
• /
• 한국해양정보통신학회 2009년도 추계학술대회
• /
• pp.913-916
• /
• 2009

본 논문에서는 한국형 표준 해쉬 알고리듬인 HAS-160을 구현하는 프로세서를 설계하였다. 각 단계연산에 사용되는 4개의 가산기는 연산성능을 높이기 위해 5:3 및 3:2 캐리보존 가산기(carry-save adder)와 캐리선택가산기(carry-select adder)의 혼합구조를 사용하였다. 설계된 HAS-160 프로세서는 512 비트 메시지로부터 160 비트의 해쉬코드를 생성하는데 82 클록주기가 소요되며, 50 MHz@3.3-V로 동작하는 경우 312 Mbps의 성능을 나타낸다. $0.35-{\mu}m$ CMOS 셀 라이브러리로 합성한 결과 약 17,600개의 게이트로 구현되었다.

• Advances in aircraft and spacecraft science
• /
• 제8권1호
• /
• pp.53-67
• /
• 2021

The increasing interest in the exploration of Mars stimulated the authors to study aerodynamic problems linked to space vehicles. The aim of this paper is to evaluate the aerodynamic effects of a flapped wing in collaborating with parachutes and retro-rockets to reduce velocity and with thrusters to control the spacecraft attitude. 3-D computations on a preliminary configuration of a blunt-cylinder, provided with flapped fins, quantified the beneficial influence of the fins. The present paper is focused on Aerodynamics of a wing section (NACA-0010) provided with a trailing edge flap. The influence of the flap deflection was evaluated by the increments of aerodynamic force and leading edge pitching moment coefficients with respect to the coefficients in clean configuration. The study was carried out by means of two Direct Simulation Monte Carlo (DSMC) codes (DS2V/3V solving 2-D/3-D flow fields, respectively). A DSMC code is indispensable to simulate complex flow fields on a wing generated by Shock Wave-Shock Wave Interaction (SWSWI) due to the flap deflection. The flap angle has to be a compromise between the aerodynamic effectiveness and the increases of aerodynamic load and heat flux on the wing section lower surface.

• Nuclear Engineering and Technology
• /
• 제53권3호
• /
• pp.942-948
• /
• 2021

The aim of this work is to help inform the decision for choosing a convenient material for the PGAA (Prompt Gamma Activation Analysis) collimator plug to be installed at the tangential channel of the Moroccan Triga Mark II Research Reactor. Two families of materials are usually used for collimator construction: a mixture of high-density polyethylene (HDPE) with boron, which is commonly used to moderate and absorb neutrons, and heavy materials, either for gamma absorption or for fast neutron absorption. An investigation of two different collimator designs was performed using N-Particle Monte Carlo MCNP6.2 code with the ENDF/B-VII.1 and MCLIP84 libraries. For each design, carbon steel and lead materials were used separately as collimator heavy materials. The performed study focused on both the impact on neutron beam quality and the neutron-gamma background at the exit of the collimator beam tube. An analysis and assessment of the principal findings is presented in this paper, as well as recommendations.

• Nuclear Engineering and Technology
• /
• 제54권11호
• /
• pp.4220-4225
• /
• 2022

Monte Carlo (MC) simulations are increasingly being used as an alternative or supplement to the gamma spectrometric method in determining the full energy peak efficiency (FEPE) necessary for radionuclide identification and quantification. The MC method is more advantageous than the experimental method in terms of both cost and time. Experimental calibration with standard sources is difficult, especially for specimens with unusually shaped geometries. However, with MC, efficiency values can be obtained by modeling the geometry as desired without using any calibration source. Modeling the detector with the correct parameters is critical in the MC method. These parameters given to the user by the manufacturer are especially the dimensions of the crystal and its front edge, the thickness of the dead layer, dimensions, and materials of the detector components. This study aimed to investigate the effect of the front edge geometry of the detector crystal on efficiency, so the effect of rounded and sharp modeled front edges on the FEPE was investigated for <300 keV with three different HPGe detectors in point and volume source geometries using PHITS MC code. All results showed that the crystal should be modeled as a rounded edge, especially for gamma-ray energies below 100 keV.