• Polymer(Korea)
• /
• v.32 no.4
• /
• pp.340-346
• /
• 2008

The aim of this study is to understand the effect of structure on the dispersion of both CNT and GNF in the phase of synthesized polyurethanes matrix. Various CNT/PU and GNF/PU composite films were prepared. Polyurethane having a different hard segment was blended with both CNT and GNF. PU having HDI as hard segment showed good dispersion with both CNT and GNF because of their linear structural character and molecular kinesis while PU having aromatic ring showed poor dispersion with those due to their structural complexity. Structural effect also induced the increase of its electro conductivity. The PU/CNT composite showed a bad dispersion (because of phase separation between PU matrix and CNT) but good electro conductivity at its surface (because CNT was collected on the surface of composite film due to low density of CNT). PU/CNT and PU/GNF composite films have quite low normalized sheet resistance value compared with silver/PU nanocomposite film because the fiber type filler could have much more contact points than that of sphere shaped silver particles have.

• Membrane and Water Treatment
• /
• v.6 no.1
• /
• pp.1-13
• /
• 2015

The modification of ultrafiltration membranes with carbon nanotube (CNT) buckypaper on fouling control was investigated. Two types of commercially available flat-sheet membranes were used: PS35 and PES900C/D (PES) (the PS35 membranes were hydrophilic with a molecular weight cutoff of 20 kDa, and the PES membranes were hydrophobic with a molecular weight cutoff of 20 kDa). The CNT buckypaper modified ultrafiltration membranes were prepared by filtering a CNT suspension through the flat-sheet membrane in a dead-end ultrafiltration unit. After modification, the pure water flux of PES was significantly increased, while the pure water flux of PS35 was decreased. The properties of the CNT modified membranes were also investigated. Considering the antifouling properties, pure water flux of the modified membrane, and the stability of CNT buckypaper layer on the membrane surface, ethanol solution with a concentration of 50 wt.%, multi-walled carbon nanotubes (MWCNTs) with a larger diameter (30-50 nm), and the CNT loading with $7.5g/m^2$ was selected. The CNT buckypaper on the surface of ultrafiltration membranes can trap the pollutants in sewage effluent and prevent them reaching the surface of virgin membranes. Water quality analysis showed that the effluent quality of the modified membrane was obviously improved. The removal efficiency of humic acid and protein-like matters by the modified membrane was significant. These results indicate the potential application of the CNT buckypaper layer modified membranes in the field of wastewater reclaim.

• Computers and Concrete
• /
• v.26 no.3
• /
• pp.213-226
• /
• 2020

The present study covenants with the static and free vibration behavior of nanocomposite sandwich plates reinforced by carbon nanotubes resting on Pasternak elastic foundation. Uniformly distributed (UD-CNT) and functionally graded (FG-CNT) distributions of aligned carbon nanotube are considered for two types of sandwich plates such as, the face sheet reinforced and homogeneous core and the homogeneous face sheet and reinforced core. Based on the first shear deformation theory (FSDT), the Hamilton's principle is employed to derive the mathematical models. The obtained solutions are numerically validated by comparison with some available cases in the literature. The elastic foundation model is assumed as one parameter Winkler - Pasternak foundation. A parametric study is conducted to study the effects of aspect ratios, foundation parameters, carbon nanotube volume fraction, types of reinforcement, core-to-face sheet thickness ratio and types of loads acting on the bending and free vibration analyses. It is explicitly shown that the (FG-CNT) face sheet reinforced sandwich plate has a high resistance against deflections compared to other types of reinforcement. It is also revealed that the reduction in the dimensionless natural frequency is most pronounced in core reinforced sandwich plate.

• Proceedings of the Materials Research Society of Korea Conference
• /
• 2009.05a
• /
• pp.32.1-32.1
• /
• 2009

현재 ITO를 대체할 재료로 투명 전도성 탄소나노튜브(carbon nanotube, CNT) 필름에 대한 연구가 진행 되고 있다. 이러한 연구에서 특히 CNT 필름의 투과도에 따른 전기저항을 향상시키기 위한 연구가 활발히 진행되고 있다. 본 연구에서는 단일벽 CNT (single-walled CNT)를 여러 가지 계면활성제로 최적 분산시킨 수용액으로부터 제조한 CNT 필름의 투과도에 따른 면 저항 (sheet resistance) 변화를 관찰하였다. 우선 계면활성제로 분산시킨 CNT 수용액을 알루미나 재질의 필터에서 정량적으로 진공 필터링하여 CNT 필름을 제조하였다. 알루미나 필터를 sodium hydroxide (NaOH) 수용액으로 용해시켜 제거함으로써 얻은 CNT 필름을 유리기판 위에 부착시켰다. 필름의 전기저항을 낮추기 위해 유리기판 위에 부착된 CNT 필름을 질산 (HNO3) 용액으로 처리하였다. Scanning electron microscopy, UV-Vis spectroscopy를 이용하여 각각 필름의 형상과 광 투과도를 분석하였고, 4-point probe로 면 저항을 측정하였다. 계면활성제로 분산시킨 CNT 필름 대부분의 면 저항은 질산 처리에 의해 감소하였다. 이는 CNT 표면에 코팅되어 있던 계면활성제가 질산에 의해 제거되었기 때문인 것으로 예상된다. 여러 계면활성제 중 sodium dodecyl benzenesulfonate로 분산시킨 CNT 필름이 산 처리 후에 가장 낮은 면 저항을 보였다. 그리고 Polyvinyl pyrrolidone (PVP)과 cetyltrimethylammonium bromide (CTAB)를 사용하여 제조한 CNT 필름의 면 저항이 가장 뚜렷한 감소를 보였다.

• Journal of Sensor Science and Technology
• /
• v.22 no.5
• /
• pp.315-320
• /
• 2013

In this paper, the properties of strain sensors made of spin-capable multi-walled carbon nanotubes (MWCNTs) were characterized and their sensing mechanisms analyzed. The key contribution of this paper is a new fabrication technique that introduces a simpler transfer method compared to spin-coating or dispersion CNT. Resistance of the MWCNT sheet strain sensor increased linearly with higher strain. To investigate the effect of CNT concentration on sensitivity, two strain sensors with different layer numbers of MWCNT sheets (one and three layers) were fabricated. According to the results, the sensor with a three-layer sheet showed higher sensitivity than that with one layer. In addition, experiments were conducted to examine the effects of environmental factors, temperature, and gas on sensor sensitivity. An increase in temperature resulted in a reduction in sensor sensitivity. It was also observed that ambient gas influenced the properties of the MWCNT sheet due to charge transfer. Experimental results showed that there was a linear change in resistance in response to strain, and the resistance of the sensor fully recovered to its unstressed state and exhibited stable electromechanical properties.

• Journal of Powder Materials
• /
• v.16 no.6
• /
• pp.424-430
• /
• 2009

Electromagnetic wave energies are consumed in the form of thermal energy, which is mainly caused by magnetic loss, dielectric loss and conductive loss. In this study, CNT was added to the nanocrystalline soft magnetic materials inducing a high magnetic loss, in order to improve the dielectric loss of the EM wave absorption sheet. Generally, the aspect ratio and the dispersion state of CNT can be changed by the pre-ball milling process, which affects the absorbing properties. After the various ball-milling processes, 1wt% of CNTs were mixed with the nanocrystalline $Fe_{73}Si_{16}B_7Nb_{3}Cu_1$ base powder, and then further processed to make EM absorption sheets. As a result, the addition of CNT to Fe-based nanocrystalline materials improved the absorption properties. However, the increase of ball-milling time for more than 1h was not desirable for the powder mixture, because the ballmilling caused the shortening of CNT length and the agglomeration of the CNT flakes.

• The Transactions of the Korean Institute of Electrical Engineers C
• /
• v.55 no.8
• /
• pp.381-386
• /
• 2006

In this study, we have investigated electrical and mechanical properties of semiconducting materials for power cable caused by CNT. Specimens were made of sheet form with the four of specimens for measurement. Volume resistivity of specimens was measured by volume resistivity meter after 10 minutes in the pre-heated oven of both $23{\pm}\;1\;[^{\circ}C]\;and\;90{\pm}\;1\;[^{\circ}C]$. And stress-strain of specimens was measured by TENSOMETER 2000. A speed of measurement was 200[mm/min], ranges of stress and strain were 400[Kgf/Cm2] and 600[%]. From this experimental results, the volume resistivity had different properties because of PTC/NTC tendency at between $23[^{\circ}C]\;and\;90[^{\circ}C]$. Also volume resistivity was low by increasing the content of CNT. It means that a small amount of CNT has a excellent electrical properties. And stress was increased, while strain was decreased by increasing the content of CNT. Thus, we could know that a small amount of CNT has a excellent electrical and mechanical oroperties.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2008.11a
• /
• pp.396-396
• /
• 2008

투명 전도성 탄소나노튜브(carbon nanotube, CNT) 필름을 터치스크린이나 디스플레이 소자 등의 전극에 응용할 목적으로, CNT 필름의 전기저항 및 광 투과도를 향상시키기 위한 연구가 활발히 진행되고 있다. 본 연구에서는 단일벽 CNT (single-walled CNT)를 여러 가지 계면활성제로 분산시킨 수용액으로부터 제조한 CNT 필름을 산 처리하여 저항 및 투과도의 변화를 관찰하였다. 우선 계면활성제로 분산시킨 CNT 수용액을 알루미나 재질의 필터에서 정량적으로 진공 필터링하여 CNT 필름을 제조하였다. 알루미나 필터를 sodium hydroxide (NaOH) 수용액으로 용해시켜 제거함으로써 얻은 CNT 필름을 유리기판 위에 부착시킨 후 광 투과도와 먼 저항 (sheet resistance)을 측정하였다. CNT 필름을 질산 ($HNO_3$) 용액에 처리하였을 때 투과도는 1~5 % 향상되었으며, 면 저항은 계면활성제로 분산시킨 CNT 필름 대부분에서 감소하였다. 이는 CNT 표면에 코팅되어 있던 계면활성제들이 산에 의해 제거되었기 때문일 것으로 추측된다. 특히 sodium dodecylbenzene sulfonate (NaDDBS)로 제조한 CNT 필름의 경우, 질산을 처리 전에는 투과도 83%, 면 저항 450 $\Omega$/sq.의 특성을 보였으나, 처리 후에는 각각 86 %, 350 $\Omega$/sq.로 향상되었다. Polyvinyl pyrrolidone (PVP)과 cetyltrimethylammonium bromide (CTAB)를 사용하여 제조한 CNT 필름의 면 저항이 가장 뚜렷한 감소를 보였다. 제조된 필름과 삼 처리된 필름 특성을 Raman spectroscopy, scanning electron microscopy, UV-Vis spectroscopy 등을 이용하여 분석하였고, 4-point probe로 면 저항을 측정하였다.

• Korean Chemical Engineering Research
• /
• v.55 no.5
• /
• pp.646-651
• /
• 2017

Size and shape of carbon nanotube (CNT) agglomerates in the dilute phase of a bubbling fluidized bed ($0.15m\;i.d{\times}2.6m\;high$) have been determined by the laser sheet technique. Axial solid holdup distribution of the CNT particles showed S curve with dense phase and dilute phase in bubbling fluidization regime. Heywood diameter and Feret diameter of the CNT agglomerates in the dilute phase of bubbling fluidized bed increased with increasing gas velocity. The CNT particle number in the agglomerates increased with increasing of gas velocity. Aspect ratio increased and circularity, roundness and solidity decreased with increasing of gas velocity. A possible mechanism of agglomerates formation was proposed based on the obtained information.

• Applied Chemistry for Engineering
• /
• v.25 no.1
• /
• pp.14-19
• /
• 2014

Nanocomposites based on poly(methyl methacrylate) (PMMA)/poly(vinylidene fluoride) (PVDF) and poly(ethylene terephthalate) (PET)/(PVDF) blended with carbon fibers (CF) and carbon nanotube (CNT) were prepared by melt mixing in the twin screw extruder. Morphologies of the PMMA/PVDF/CF/CNT and PET/PVDF/CF/CNT nanocomposites were investigated using SEM. The aggregation of CNT was observed in PMMA/PVDF/CF/CNT nanocomposites while the good dispersion of CNT was shown in PET/PVDF/CF/CNT nanocomposites. In SEM image of PET/PVDF/CF/CNT nanocomposite, the CNT were mainly located at the PET domain of phase-separated PET/PVDF blend due to the ${\pi}-{\pi}$ interaction between the phenyl ring of PET and graphite sheet of the CNT's surface. In addition, a fairly good compatibility between PET/PVDF matrix and CF was shown in the SEM image. In the case of PET/PVDF nanocomposites blended with the co-addition of CF and CNT, the volume electrical resistivity decreased while no change was observed in PMMA/PVDF/CF/CNT composites. The degree of CNT dispersion in morphology results was consistent with the electrical conductivity results. From the DSC results, the crystallization temperature (Tc) of PET/PVDF/CF/CNT nanocomposites increased due to the co-addition of CF and CNTs acting as a nucleating agent. Flexural modulus of PET/PVDF/CF/CNT were sharply enhanced due to increasing the interaction between PET and CF.