• Journal of Environmental Science International
• /
• v.25 no.11
• /
• pp.1485-1491
• /
• 2016

PSf/D2EHPA/CNT beads were prepared by immobilizing di-(2-ethylhexyl)-phosphoric acid (D2EHPA) and carbon nanotubes (CNT) on polysulfone (PSf) and used to remove Cu(II) from aqueous solutions. Optimum pH was in the range of 4 to 6. The removal kinetic of Cu(II) by the prepared PSf/D2EHPA/CNT beads was mainly governed by internal diffusion, and the diffusion coefficient of Cu(II) by PSf/D2EHPA/CNT beads was found to be $2.19{\times}10^{-4}{\sim}2.64{\times}10^{-4}cm^2/s$. The Langmuir isotherm model predicted the experimented data well. The maximum removal capacity of Cu(II) obtained from this isotherm was 7.32 mg/g. Calculated thermodynamic parameters such as ${\Delta}G^o$, ${\Delta}H^o$ and ${\Delta}S^o$ showed that the adsorption of Cu(II) ions onto PSf/D2EHPA/CNT beads was feasible, spontaneous and endothermic at 293-323 K.

• Journal of Industrial Technology
• /
• v.33 no.A
• /
• pp.67-72
• /
• 2013

CNT(carbon nanotube) humidity sensors with plasma treated electrodes exhibit a much faster response time and a higher sensitivity to humidity, compared to untreated CNT and porous Cr electrodes. These results may be partially due to their percolated pore structure being more accessible for water molecules and for expending the diffusion of moisture to the polyimide sensing film, and partially due to the oxygenated surface of CNT films. This paper shows a plasma process effect and selectivity characteristics of CNT film humidity sensor.

• Korean Chemical Engineering Research
• /
• v.54 no.4
• /
• pp.574-581
• /
• 2016

In this study, CNT functionalized with pyrrolidine ring via 1,3-dipolar cycloaddition reaction with various amino acid and aldehyde was synthesized. Metallocene was subsequently immobilized on the functionalized CNT and CNT/polyethylene composite was prepared via in-situ ethylene polymerization. The polymerization activities of metallocene supported on CNT functionalized with glycine and benzaldehyde (Gly+BA-CNT) were similar to those of metallocene supported on CNT functionalized with N-benzyloxycarbonylglycine and paraformaldehyde (Z-Gly+PFA-CNT) although its Zr content was lower than that of Z-Gly+PFA-CNT. In the case of metallocene supported on Z-Gly+PFA-CNT, the even distribution of active sites hindered the diffusion of ethylene monomer and cocatalyst MAO due to steric hindrance during ethylene polymerization. Compared to polyethylene produced from homogeneous metallocene catalysts, CNT/PE composites had a higher initial degradation temperature ($T_{onset}$) and maximum mass loss temperature ($T_{max}$). It suggests that pyrrolidine functionalized CNT is uniformly dispersed and strongly interacted with the PE matrix, enhancing the thermal stability of PE.

• Korean Chemical Engineering Research
• /
• v.55 no.6
• /
• pp.771-777
• /
• 2017

Adsorption characteristics of Eosin Y dye by carbon nano tubes (CNTs) were examined through batch experiments. CNTs used in the study had specific surface area of $106.9m^2/g$, porosity volume of $1.806cm^3/g$, and porosity diameter of $163.2{\AA}$, respectively. Adsorption experiments were carried out as function of contact time, initial solution pH (2~10), dye concentration (100, 150 and 200 mg/L), adsorbent dose (0.05~1.0 g) and temperature (293, 313 and 333 K). The adsorption was favoured at lower pHs and temperatures. Adsorption data were well described by the Langmuir model. The adsorption process followed the pseudo-second order kinetic model. The adsorption capacity decreased with increase in temperature. The results of the intraparticle diffusion model suggested that film diffusion and particle diffusion were simultaneously occured during the adsorption process. Thermodynamic studies suggested the spontaneous and endothermic nature of adsorption of Eosin Y dye onto CNTs.

• Carbon letters
• /
• v.14 no.4
• /
• pp.228-233
• /
• 2013

In this work, we report in-situ observations of changes in catalyst morphology, and of growth termination of individual carbon nanotubes (CNTs), by complete loss of the catalyst particle attached to it. The observations strongly support the growth-termination mechanism of CNT forests or carpets by dynamic morphological evolution of catalyst particles induced by Ostwald ripening, and sub-surface diffusion. We show that in the tip-growth mode, as well as in the base-growth mode, the growth termination of CNT by dissolution of catalyst particles is plausible. This may allow the growth termination mechanism by evolution of catalyst morphology to be applicable to not only CNT forest growth, but also to other growth methods (for example, floating-catalyst chemical vapor deposition), which do not use any supporting layer or substrate beneath a catalyst layer.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2010.02a
• /
• pp.72-72
• /
• 2010

탄소나노튜브(carbon nanotubes : CNTs)는 뛰어난 전기적, 물리적인 특성을 가지고 있기 때문에 다양한 분야에서 이를 활용하려는 노력들이 활발히 이루어지고 있다. CNTs의 전기적인 특성은 직경에 의해 결정되므로, 직경을 균일하게 제어하는 일이 CNTs를 기반으로 한 전자소자 응용에 가장 중요한 사항이라 할 수 있다. 일반적으로 화학기상증착법(chemical vapor deposition, CVD)으로 합성된 CNTs의 직경은 촉매의 크기에 의존하기 때문에, 촉매의 크기를 제어하기 위한 다양한 연구들이 활발히 진행되고 있다[1-3]. 하지만 CNTs의 성장온도 근처에서 촉매 입자는 표면 확산(surface diffusion)에 의해 응집(agglomeration)되기 때문에 작고 균일한 크기의 촉매를 얻기 어렵다. 본 연구에서는 Si(001) 기판 위에 지지층(supporting layer)인 Al의 두께를 변화시켜 증착하고, 열적산화과정을 통해 $Al_2O_3$ 층을 형성한 후 Fe을 증착하여 CNTs를 합성하였다. $Al_2O_3$ 지지층과 Fe 촉매입자의 구조와 화학적 상태를 원자힘현미경 (atomic force microscopy, AFM), 주사전자현미경 (scanning electron microscopy, SEM), 투과전자현미경 (transmission electron microscopy, TEM), X-선 광전자 분광기(X-ray photoelectron spectroscopy)를 통해 분석하였고, 성장된 CNTs는 SEM, TEM, 라만 분광법 (Raman spectroscopy)을 통해 분석하였다. 그 결과, $Al_2O_3$ 층은 두께에 따라 각기 다른 표면 거칠기(RMS roughness)와 결정립(grain)의 크기를 갖게 되며, 이러한 표면구조가 Fe 촉매입자의 표면확산에 의한 응집에 관여하여 CNTs의 직경에 영향을 미치는 것을 확인하였다. 또한 $Al_2O_3$ 지지층의 두께가 15 nm인 경우, Fe의 응집현상이 억제되어 좁은 직경분포를 지닌 고순도 단일벽 탄소나노튜브(Single-walled CNTs)가 성장되는 것을 확인하였다.

• Journal of the Korean Society of Marine Environment & Safety
• /
• v.20 no.6
• /
• pp.768-773
• /
• 2014

In this study, experimental and numerical studies for the synthesis of carbon nanotube(CNT) in methane counterflow diffusion flame have been performed. Methane mixed with acetylene($C_2H_2$) was used as a fuel gas and ferrocene was used as a catalyst for synthesis of CNT. The major parameters was $C_2H_2$ mixing rate and mixing rates were 2 %, 6 %, and 10 %. Characteristics of CNT formation on grid were analyzed from SEM images. the chemical reaction mechanism adopted is GRI-MECH 3.0. Numerical results showed that flame temperature and CO mole fraction were increased with increasing acetylene mixing rate. Experimental results showed that the CNT synthesis in 2% acetylene mixture flame better than that of 6% and 10% acetylene mixture flames. It can be considered that 6% and 10% acetylene mixture flames generated the excessive carbon source and then it interrupted the supplement of the carbon source into ferrocene catalyst. It can be found that the supply of appropriate quantity of carbon source can make effect to synthesis of high purity of CNT.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2016.02a
• /
• pp.297.2-297.2
• /
• 2016

Photoacoustic generation of ultrasound is an effective approach for development of high-frequency and high-amplitude ultrasound transmitters. This requires an efficient energy converter from optical input to acoustic output. For such photoacoustic conversion, various light-absorbing materials have been used such as metallic coating, dye-doped polymer composite, and nanostructure composite. These transmitters absorb laser pulses with 5-10 ns widths for generation of tens-of-MHz frequency ultrasound. The short optical pulse leads to rapid heating of the irradiated region and therefore fast thermal expansion before significant heat diffusion occurs to the surrounding. In this purpose, nanocomposite thin films containing gold nanoparticles, carbon nanotubes (CNTs), or carbon nanofibers have been recently proposed for high optical absorption, efficient thermoacosutic transfer, and mechanical robustness. These properties are necessary to produce a high-amplitude ultrasonic output under a low-energy optical input. Here, we investigate carbon nanotube (CNT)-polydimethylsiloxane (PDMS) composite transmitters and their nanostructure-originated characteristics enabling extraordinary energy conversion. We explain a thermoelastic energy conversion mechanism within the nanocomposite and examine nanostructures by using a scanning electron microscopy. Then, we measure laser-induced damage threshold of the transmitters against pulsed laser ablation. Particularly, laser-induced damage threshold has been largely overlooked so far in the development of photoacoustic transmitters. Higher damage threshold means that transmitters can withstand optical irradiation with higher laser energy and produce higher pressure output proportional to such optical input. We discuss an optimal design of CNT-PDMS composite transmitter for high-amplitude pressure generation (e.g. focused ultrasound transmitter) useful for therapeutic applications. It is fabricated using a focal structure (spherically concave substrate) that is coated with a CNT-PDMS composite layer. We also introduce some application examples of the high-amplitude focused transmitter based on the CNT-PDMS composite film.

• Journal of Environmental Health Sciences
• /
• v.38 no.1
• /
• pp.1-7
• /
• 2012

Carbon nanotubes (CNTs) stand at the frontier of nanotechnology and are destined to stimulate the next industrial revolution. Rapid increase in their production and use in the technology industry have led to concerns over the effects of CNT on human health and the environment. The prominent use of CNTs in biomedical applications also increases the possibility of human exposure, while properties such as their high aspect ratio (fiber-like shape) and large surface area raise safety concerns for human health if exposure does occur. It is crucial to develop viable alternatives to in vivo tests in order to evaluate the toxicity of engineered CNTs and develop validated experimental models capable of identifying CNTs' toxic effects and predicting their level of toxicity in the human respiratory system. Human lung epithelial cells serve as a barrier at the interface between the surrounding air and lung tissues in response to exogenous particles such as air-pollutants, including CNTs. Monolayer culture of the key individual cell types has provided abundant fundamental information on the response of these cells to external perturbations. However, such systems are limited by the absence of cell-cell interactions and their dynamic nature, which are both present in vivo. In this review, we suggested two viable alternatives to in vivo tests to evaluate the health risk of human exposure to CNTs.

• Steel and Composite Structures
• /
• v.36 no.1
• /
• pp.87-101
• /
• 2020

A multi-scale epoxy/CNT/fiberglass annular sector plate is studied in this paper in the view of determining nonlinear forced vibration characteristics. A 3D Mori-Tanaka model is employed for evaluating multi-scale material properties. Thus, all of glass fibers are assumed to have uni-direction alignment and CNTs have random diffusion. The geometry of annular sector plate can be described based on the open angle and the value of inner/outer radius. In order to solve governing equations and derive exact forced vibration curves for the multi-scale annular sector, Jacobi elliptic functions are used. Obtained results demonstrate the significance of CNT distribution, geometric nonlinearity, applied force, fiberglass volume, open angle and fiber directions on forced vibration characteristics of multi-scale annular sector plates.