• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2004년도 하계학술대회 논문집 Vol.5 No.1
• /
• pp.252-255
• /
• 2004

반도체는 high integrated, high speed, low power를 위하여 design 뿐만 아니라 재료 측면에서도 많은 변화를 가져오고 있으며, RC delay time을 줄이기 위하여 Al 배선보다 비저항이 낮은 Cu와 low-k material 적용이 그 대표적인 예이다. 그러나, Cu 배선의 경우 dry etching이 어려우므로, 기존의 공정으로는 그 한계를 가지므로 damascene 또는 dual damascene 공정이 소개, 적용되고 있다. Damascene 공정은 절연막에 photo와 RIE 공정을 이용하여 trench를 형성시킨 후 electrochemical plating 공정을 이용하여 trench에 Cu를 filling 시킨다. 이후 CMP 공정을 이용하여 절연막 위의 Cu와 barrier material을 제거함으로서 Cu 배선을 형성하게 된다. Dual damascene 공정은 trench와 via를 동시에 형성시키는 기술로 현재 대부분의 Cu 배선 공정에 적용되고 있다. Cu CMP는 기존의 metal CMP와 마찬가지로 oxidizer를 이용한 Cu film의 화학반응과 연마 입자의 기계가공이 기본 메커니즘이다. Cu CMP에서 backside pressure 영향이 uniformity에 미치는 영향을 살펴보았으며, electrochemical plating 공정에서 발생하는 hump가 CMP 결과에 미치는 영향과 dishing 결과를 통하여 그 영향을 평가하였다.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2006년도 춘계학술대회 논문집
• /
• pp.479-480
• /
• 2006

The purpose of this paper is to investigate the relationship between CMP(Chemical Mechanical Polishing) characteristics of ITO thin film and friction signal by using the CMP monitoring system. Suba 400 pad and MSW2000 slurry of the Rohm & Haas Co. was used in this experiment to investigate the charateristics of ITO CMP. From this experiment, it is proven that the coefficient of friction is related to uniformity of the removal rate of the ITO thin film. Therefore, the prediction of polishing result would be possible by measuring friction signal.

• 한국철도학회:학술대회논문집
• /
• 한국철도학회 2004년도 추계학술대회 논문집
• /
• pp.836-841
• /
• 2004

Recently, the development of the paved track is required as a Low-maintenance of conventional line. The main reason is that the line capacity and bearing of track are increased progressively. The most important factor of paved track is stability and applicability. To be based on this subject, Cement Mortar Pouring(CMP) paved track is developed. CMP paved track is a kind of ballast reinforced track using the pre packed concrete technique. The most important to design is characteristics of the structure. CMP slab's thickness is less than the conventional slab track and pouring layer is attached tie and roadbed directly. On this paper, to verify the basic structure of the CMP track, characteristics of the structure is investigated pouring layer, tie and interaction of the each layer using the 3D finite elment analysis.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2006년도 추계학술대회 논문집 전기물성,응용부문
• /
• pp.107-108
• /
• 2006

In this work, we first applied the chemical mechanical polishing (CMP) process to the planarization of ferroelectric film in order to obtain a good planarity of electrode/ferroelectric film interface. $Bi_{3.25}La_{0.75}Ti_{3}O_{12}$ (BLT) ferroelectric film was fabricated by the sol-gel method. However, there have been serious problems in CMP in terms of repeatability and defects in patterned wafer. Especially, dishing & erosion defects increase the resistance because they decrease the interconnect section area, and ultimately reduce the lifetime of the semiconductor. Cross-sections of the wafer before and after CMP were examined by Scanning electron microscope(SEM). Process characteristics of non-dishing and erosion were investigated.

• 대한전기학회논문지:전기물성ㆍ응용부문C
• /
• 제55권12호
• /
• pp.549-554
• /
• 2006

In this paper we first applied the chemical mechanical polishing (CMP) process to the planarization of ferroelectric film in order to obtain a good planarity between electrode and ferroelectric film. $Pb_{1.1}(Zr_{0.52}Ti_{0.48})O_3$ (shortly PZT) ferroelectric film was fabricated by the sol-gel method. And then, we compared the structural characteristics before and after CMP process of PZT films. Removal rate, WIWNU% and surface roughness have been found to depend on slurry abrasive types and their hardness, especially, surface roughness and planarity were strongly depends on its pH value. A maximum in the removal rate is observed in the silica slurry, in contrast with the minimum removal rate occurs at ceria slurry. We found that the surface roughness of PZT films can be significantly reduced using the CMP technique.

• 한국전기화학회:학술대회논문집
• /
• 한국전기화학회 2003년도 춘계총회 및 학술발표회
• /
• pp.42-42
• /
• 2003

• 전기전자학회논문지
• /
• 제23권4호
• /
• pp.1175-1181
• /
• 2019

논문에서는 1:10으로 희석된 실리카 슬러리에 산화망간(MnO₂) 연마제를 첨가하여 재처리된 혼합연마제 슬러리(Mixed Abrasive Slurry; MAS)의 화학기계적연마(CMP) 특성을 연구하였다. 최적의 연마 성능을 갖는 슬러리를 설계하기 위해서는 높은 연마율, 하부층에 대한 적절한 연마선택비, 연마 후의 낮은 표면결함, 슬러리의 안정성 등을 얻어야 한다. 산화망간이 첨가된 MAS의 연마 성능은 연마율 및 비균일도와 같은 CMP 성능, 입도 분석, 표면 형상에 대해 평가하였다. 실험결과, 높은 연마율과 낮은 비균일도 측면에서 볼 때 원액 실리카 슬러리와 대등한 슬러리 특성을 얻을 수 있었다. 따라서 본 연구에서 제안하는 MnO₂-MAS를 사용하면 고가의 소모재인 슬러리를 절약하는데 매우 유용할 것이다.

• 한국전기전자재료학회논문지
• /
• 제18권7호
• /
• pp.605-609
• /
• 2005

Chemical mechanical polishing (CMP) of Ni was performed by the various ratios of four kinds of oxidizers and an addition of alumina powders as an abrasive in each slurry with the different oxidizers. Moreover, the interaction between the Ni and the each oxidizer was discussed by potentiodynamic polarization measurement, in order to compare the effects of Ni-CMP and electrochemical characteristics on the Ni with the different oxidizers. As an experimental result, the removal rate of Ni reached a maximum at 1 $vol\%$ of $H_2O_2$. Also the removal rates of Ni increased with the audition of alumina abrasives in each slurry. The potentiodynamic polarization of Ni under dynamic condition showed a significant difference in electrochemical behavior by addition of $H_2O_2$ in solutions. Ni showed the perfect passivation behavior in solution without $H_2O_2$ under potentiodynamic polarization condition, while active dissolution dominates in solution with the addition of $H_2O_2$. The results indicate that the surface chemistry and electrochemical characteristics of Ni play an important role in controlling the polishing behavior of Ni.

• 한국전기전자재료학회논문지
• /
• 제17권10호
• /
• pp.1041-1048
• /
• 2004

Chemical mechanical polishing (CMP) process was studied in terms of tribology in this paper. CMP performed by the down force and the relative motion of pad and wafer with slurry is typically tribological system composed of friction, wear and lubrication. The piezoelectric quartz sensor for friction force measurement was installed and the friction force was detected during CMP process. Various friction signals were attained and analyzed with the kind of pad, abrasive and abrasive concentration. As a result of experiment, the lubrication regime is classified with ηv/p(η, v and p; the viscosity, relative velocity and pressure). The characteristics of friction and material removal mechanism is also different as a function of the kind of abrasive and the abrasive concentration in slurry. Especially, the material removal per unit distance is directly proportional to the friction force and the non~uniformity has relation to the coefficient of friction.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2003년도 춘계학술대회 논문집 센서 박막재료 반도체 세라믹
• /
• pp.162-165
• /
• 2003

The corrosion characteristics of diffusion barrier in Copper CMP has been investigated. Key experimental variables that has been investigated are the corrosion rate by different agents containing slurry of Cu CMP. Whenever Cu and Ta films were corroded adding each oxidizer, the corrosion rate of Ta was much lower than that of Cu. That is, the difference in the corrosion rates of Ta by oxidizer was not larger as compared with Cu. As corroded by complexing agents, the corrosion rate of Ta was close to O. The corrosion rate of Ta increased as added $HNO_3$ and $CH_3COOH$ compared with the reference slurry; on the other hand, it decreased with addition of HF. In addition, resulting corrosion rate went up with lower pH of agent. The corrosion rates by agents were however significant small; hence, it doesn't affect on the removal rate of Cu CMP practically. Consequently, this can be explained by assuming that the mechanical effect dominates than the chemical effect on the polishing rate of Ta(TaN).