• 한국ITS학회:학술대회논문집
• /
• v.2006 no.10
• /
• pp.312-315
• /
• 2006

• Proceedings of the IEEK Conference
• /
• 2008.06a
• /
• pp.531-532
• /
• 2008

In this paper, we present the comparison of the CMOS Double-Balanced Mixer for WLAN applications using the tail current source and not using it at the same current. The mixers are derived from the Gilbert cell mixer and have been simulated by using TSMC $0.18{\mu}m$ RF CMOS technology.

• Journal of IKEEE
• /
• v.7 no.2 s.13
• /
• pp.236-244
• /
• 2003

In this paper, RF and IF circuits for mobile terminals which have usually been implemented using expensive BiCMOS processes are designed using CMOS circuits, and a Tx CMOS RF/IF single chip for PCS applications is designed. The designed circuit consists of an IF block including an IF PLL frequency synthesizer, an IF mixer, and a VGA and an RF block including a SSB RF mixer and a driver amplifier, and performs all transmit signal processing functions required between digital baseband and the power amplifier. The phase noise level of the designed IF PLL frequency synthesizer is -114dBc/Hz@100kHz and the lock time is less than $300{\mu}s$. It consumes 5.3mA from a 3V power supply. The conversion gain and OIP3 of the IF mixer block are 3.6dB and -11.3dBm. It consumes 5.3mA. The 3dB frequencies of the VGA are greater than 250MHz for all gain settings. The designed VGA consumes 10mA. The designed RF block exhibits a gain of 14.93dB and an OIP3 of 6.97dBm. The image and carrier suppressions are 35dBc and 31dBc, respectively. It consumes 63.4mA. The designed circuits are under fabrication using a $0.35{\mu}m$ CMOS process. The designed entire chip consumes 84mA from a 3V supply, and its area is $1.6㎜{\times}3.5㎜$.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.39A no.12
• /
• pp.691-698
• /
• 2014

An L-band single side band(SSB) mixer with CMOS switches and a C-band quadrature voltage-controlled oscillator(QVCO) have been developed using the TowerJazz 0.18-um RFCMOS process. The SSB mixer exhibits a conversion gain of 6.6 ~ 7.5 dB with a 70-dBc image rejection ratio and 65-dBc port isolation. The oscillation frequency range of the QVCO is 6.2 ~ 6.7 GHz with an output power of 4~6 dBm. For measurement, 1.8 V supply voltage is used while drawing 36 mA for the mixer and 23 mA for the QVCO.

• Journal of IKEEE
• /
• v.4 no.2 s.7
• /
• pp.202-211
• /
• 2000

Utilizing the circuit simulator SPICE, we designed a 1.9GHz CMOS up-conversion mixer and explained in detail the simulation procedures including device modeling for the circuit design. Since the measured characteristics of the chip fabricated using the $0.5{\mu}m$ standard CMOS process had shown a big deviation from the characteristics expected by the original simulations, we tried to figure out the proper reasons for the discrepancies. Simulations considering the discovered problems in the original simulations have shown the validity of the simulation method tried for the design. We have shown that the utilized standard CMOS process can be used for the implementation of the chip characteristics similar to those of the equivalent chip fabricated using the GaAs MESFET process.

• JSTS:Journal of Semiconductor Technology and Science
• /
• v.2 no.1
• /
• pp.30-40
• /
• 2002

A 2.45GHz double-balanced modified Gilbert-type CMOS up-conversion mixer design is introduced, where the PMOS current-reuse bleeding technique is demonstrated to be efficient in improving conversion gain, linearity, and noise performance. An LO buffer is included in the mixer design to perform single-ended to differential conversion of the LO signal on chip. Simulation results of the design based on careful modeling of all active and passive components are examined to explain in detail about the characteristic improvement and degradation provided by the proposed design. Two kinds of chips were fabricated using a standard $0.35\mu\textrm$ CMOS process, one of which is the mixer chip without the LO buffer and the other is the one with it. The measured characteristics of the fabricated chips are quite excellent in terms of conversion gain, linearity, and noise, and they are in close match to the simulation results, which demonstrates the adequacy of the modeling approach based on the macro models for all the active and passive devices used in the design. Above all the benefits provided by the current-reuse bleeding technique, the improvement in noise performance seems most valuable.

• ETRI Journal
• /
• v.27 no.5
• /
• pp.579-584
• /
• 2005

A CMOS direct-conversion mixer with a single transistor-level topology is proposed in this paper. Since the single transistor-level topology needs smaller supply voltage than the conventional Gilbert-cell topology, the proposed mixer structure is suitable for a low power and highly integrated RF system-on-a-chip (SoC). The proposed direct-conversion mixer is designed for the multi-band ultra-wideband (UWB) system covering from 3 to 7 GHz. The conversion gain and input P1dB of the mixer are about 3 dB and -10 dBm, respectively, with multi-band RF signals. The mixer consumes 4.3 mA under a 1.8 V supply voltage.

• JSTS:Journal of Semiconductor Technology and Science
• /
• v.2 no.2
• /
• pp.147-155
• /
• 2002

This paper describes RF front-end transceiver chipset for the dual-mode operation of PCS-Korea and IMT-2000. The transceiver chipset has been implemented in a $0.25\mutextrm{m}$ single-poly five-metal CMOS technology. The receiver IC consists of a LNA and a down-mixer, and the transmitter IC integrates an up-mixer. Measurements show that the transceiver chipset covers the wide RF range from 1.8GHz for PCS-Korea to 2.1GHz for IMT-2000. The LNA has 2.8~3.1dB NF, 14~13dB gain and 5~4dBm IIP3. The down mixer has 15.5~16.0dB NF, 15~13dB power conversion gain and 2~0dBm IIP3. The up mixer has 0~2dB power conversion gain and 6~3dBm OIP3. With a single 3.0V power supply, the LNA, down-mixer, and up-mixer consume 6mA, 30mA, and 25mA, respectively.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.22 no.9
• /
• pp.1941-1948
• /
• 1997

In this paper, the power efficient linear upconversion mixer which is a functional circuit in transmit path of intermediate frequency(IF) part of Code Division Multiple (CDMA) cellular phone was explained. In generally, the low CMOS devices limits the implementation of upconversion mixer especially for lower loads. Using replica transconductor, the linear range is extended up to the limit. Thiscircuit was imprlemented using $0.8{\mu}\textrm{m}$ N-well CMOS technology with 2-poly/2-metal. The active area of chip is $0.53mm{\times}0.92mm$. The power consumption is 30mW with 3.3V suply voltage. The 1dB conpression characteristics is -27.3dB with $25{\Omega}$. load and being applied by 2-tone input signal. The mixer operates properly above 200MHz.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.46 no.2
• /
• pp.45-49
• /
• 2009

In this paper, a direct down conversion LNA/Mixer has been designed and tested for 900Mhz UHF RFID application. The designed circuit has been implemented in 0.18um CMOS technology with 3.3V operation. In this work, a common gate input architecture has been used to cope with the higher input self jamming level. This LNA/Mixer is designed to support two operating modes of high gain mode and low gain mode according to the input jamming levels. The measured results show that the input referred P1dBs are 4dBm of high gain mode and 11dBm of low gain mode, and the conversion gains are 12dB and 3dB in high and low gain mode respectively The power consumptions are 60mW for high gain mode and 79mW for low gain mode. The noise figures are 16dB and 20dB in high gain mode and low gain mode respectively.