• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.40 no.9
• /
• pp.673-684
• /
• 2003

A degenerated differential pair has been widely used as a standard topology for digitally programmable CMOS VGAs. A variable degeneration resistor has been implemented using a resistor string or R-2R ladder with MOSFET switches. However, in the VGAs using these conventional methods, low-voltage and high-speed operation is very hard to achieve due to the dc voltage drop over the degeneration resistor. To overcome this problem a new variable degeneration resistor is proposed where the dc voltage drop is almost removed. Using the proposed gain control scheme, a low-voltage and high-speed CMOS VGA is designed. HSPICE simulation results using a 0.25${\mu}{\textrm}{m}$ CMOS process parameters show that the designed VGA provides a 3dB bandwidth of 360MHz and a 80dB gain control range in 2dB step. Gain errors are less than 0.4dB at 200MHz and less than l.4dB at 300MHz. The designed circuit consumes 10.8mA from a 2.5V supply and its die area is 1190${\mu}{\textrm}{m}$${\times}$360${\mu}{\textrm}{m}$.

• Proceedings of the IEEK Conference
• /
• 2003.07b
• /
• pp.947-950
• /
• 2003

본 논문에서는 고속 적외선 무선 데이터통신(IrDA) 에 사용되는 트랜스임피던스 증폭기(Transimpedance Amplifier)를 설계하였다. 트랜스임피던스 증폭기는 잡음을 최소화하기 위해 PMOS 차동 구조로 설계하였으며 입력과 출력의 피드백을 통해 주위의 빛에 의해 발생되는 photocurrent 에 의한 DC 옵셋을 제거하였다 또한 공통 게이트(CG)와 Regulated Cascode Circuit (RGC)을 추가하여 대역폭(Bandwidth)을 향상시켰다. 설계한 회로는 0.25 um CMOS 공정을 이용하였으며 트랜스임피던스 이득은 200 MHz의 대역폭에서 10 KΩ (80 dBΩ )이다. 전체 전력 소비는 18 mW이다.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.43 no.6 s.348
• /
• pp.53-61
• /
• 2006

In high speed flash type or pipelining type A/D Converter, the faster sampling frequency is, the more the effect of DC reference fluctuation is increased by clock feed-through and kick-back. When we measure A/D Converter, further, external noise increases reference voltage fluctuation. Thus reference fluctuation reduction circuit must be needed in high speed A/D converter. Conventional circuit simply uses capacitor but layout area is large and it's not efficient. In this paper, a reference fluctuation reduction circuit using transmission gate is proposed. In order to verify the proposed technique, we designed and manufactured 6bit 2GSPS CMOS A/D converter. The A/D converter is based on 0.18um 1-poly 5-metal N-well CMOS technology, and it consumes 145mW at 1.8V power supply. It occupies chip area of $977um\times1040um$. Experimental result shows that SNDR is 36.25 dB and INL/DNL ${\pm}0.5LSB$ when sampling frequency is 2GHz.

• Journal of the Institute of Electronics Engineers of Korea SC
• /
• v.39 no.3
• /
• pp.201-210
• /
• 2002

This paper describes a 3.3 (V) low power 4 digit CMOS quaternary to analog converter (QAC) designed with a neuron MOS($\upsilon$MOS) down literal circuit block and cascode current mirror source block. The neuron MOS down literal architecture allows the designed QAC to accept not only 4 level voltage inputs, but also a high speed sampling rate quaternary voltage source LSB. Fast settling time and low power consumption of the QAC are achieved by utilizing the proposed architecture. The simulation results of the designed 4 digit QAC show a sampling rate of 6(MHz) and a power dissipation of 24.5 (mW) with a single power supply of 3.3 (V) for a CMOS 0.35${\mu}{\textrm}{m}$ n-well technology.

• Proceedings of the Korea Information Processing Society Conference
• /
• 2009.11a
• /
• pp.405-406
• /
• 2009

4-2 compressor는 곱셈기의 부분 곱 합 트리(partial product summation tree)의 기본적인 구성요소이다. 본 논문은 저 전력 특성을 갖는 4-2 compressor 구조를 제안한다. 제안한 회로는 한 개의 전가산기와 MUX로 구성하였다. 이 회로는 기존의 회로와 비교하였을 때 회로 구성에 필요한 트랜지스터수가 14개 감소하였으며, 6.3%의 전력소모가 감소하였다. 제안한 회로는 Samsung 0.18um CMOS 공정을 이용하여 HSPICE로 시뮬레이션 하였다.

• Journal of the Institute of Electronics and Information Engineers
• /
• v.53 no.3
• /
• pp.46-55
• /
• 2016

This work proposes a 13b 100MS/s 45nm CMOS ADC with a high dynamic performance for IF-domain high-speed signal processing systems based on a four-step pipeline architecture to optimize operating specifications. The SHA employs a wideband high-speed sampling network properly to process high-frequency input signals exceeding a sampling frequency. The SHA and MDACs adopt a two-stage amplifier with a gain-boosting technique to obtain the required high DC gain and the wide signal-swing range, while the amplifier and bias circuits use the same unit-size devices repeatedly to minimize device mismatch. Furthermore, a separate analog power supply voltage for on-chip current and voltage references minimizes performance degradation caused by the undesired noise and interference from adjacent functional blocks during high-speed operation. The proposed ADC occupies an active die area of $0.70mm^2$, based on various process-insensitive layout techniques to minimize the physical process imperfection effects. The prototype ADC in a 45nm CMOS demonstrates a measured DNL and INL within 0.77LSB and 1.57LSB, with a maximum SNDR and SFDR of 64.2dB and 78.4dB at 100MS/s, respectively. The ADC is implemented with long-channel devices rather than minimum channel-length devices available in this CMOS technology to process a wide input range of $2.0V_{PP}$ for the required system and to obtain a high dynamic performance at IF-domain input signal bands. The ADC consumes 425.0mW with a single analog voltage of 2.5V and two digital voltages of 2.5V and 1.1V.

• The Journal of the Korea institute of electronic communication sciences
• /
• v.18 no.5
• /
• pp.777-784
• /
• 2023

A sense amplifier is an essential peripheral circuit for designing a memory and is used to sense a small differential input signal and amplify it into digital signal. In this paper, a high-speed sense amplifier applicable to in-memory computing circuits is proposed. The proposed circuit reduces sense delay time through transistor Mtail that provides an additional discharge path and improves the circuit performance of the sense amplifier by applying m-GDI (: modified Gate Diffusion Input). Compared with previous structure, the sense delay time was reduced by 16.82%, the PDP(: Power Delay Product) by 17.23%, the EDP(: Energy Delay Product) by 31.1%. The proposed circuit was implemented using TSMC's 65nm CMOS process, while its feasibility was verified through SPECTRE simulation in this study.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.39 no.7
• /
• pp.57-65
• /
• 2002

In this paper, a 2.5V 10-bit 300MSPS CMOS D/A Converter is described. The architecture of the D/A Converter is based on a current steering 8+2 segmented type, which reduces non-linearity error and other secondary effects. In order to achieve a high performance D/A Converter, a novel current cell with a low spurious deglitchnig circuit and a novel inverse thermomeer decoder are proposed. To verify the performance, it is integrated with $0.25{\mu}m$ CMOS 1-poly 5-metal technology. The effective chip area is $1.56mm^2$ and power consumption is about 84mW at 2.5V power supply. The simulation and experimental results show that the glitch energy is 0.9pVsec at fs=100MHz, 15pVsec at fs=300MHz in worst case, respectively. Further, both of INL and DNL are within ${\pm}$1.5LSB, and the SFDR is about 45dB when sampling, frequency, is 300MHz and output frequency is 1MHz.

• Journal of the Korean Institute of Telematics and Electronics C
• /
• v.36C no.12
• /
• pp.20-26
• /
• 1999

A CMOS 6-bit 100MSPS ADC for DBS receiver is designed. The proposed ADC is composed of folding block, latch block, and digital block. The cascode interpolating block and kickback reduced latch are proposed with a high speed architecture. To verify the performance of ADC, simulations are carried out by HSPICE. The ADC achieves a clock frequency of 100MHz with a power dissipation of 40mW for 3 V supply voltage. The active chip area is $1500{\mu}m{\times}1000{\mu}m$with $0.65{\mu}m$ 2-poly 2-metal CMOS process. Further, INL and DNL are within ${\pm}0.6LSB$, ${\pm}0.5LSB$, respectively. SNDR is about 33dB at 10MHz input frequency.

• The Transactions of the Korea Information Processing Society
• /
• v.7 no.1
• /
• pp.235-244
• /
• 2000

This paper presents a low power PLL based clock geneator circuit for microprocessors. It generates 32MHz${\sim}$1GHz clocks and can be integrated inside microprocessor chips. A high speed D Flip-Flop is designed using dynamic differential latch and a new Phase Frequency Detector(PFD) based on this FF is presented. The PFD enjoys low error characteristics in phase sensitivity and the PLL using this PFD has a low phase error. To improve the linearity of voltage controlled oscillator(VCO) in PLL, the voltage to current converter and current controlled oscillator combination is suggested. The resulting PLL provides wide lock range and extends frequency of generated clocks over 1 GHz. The clock generator is designed by using $0.65\;{\mu}m$ CMOS full custom technology and operates with $11\;{\mu}s$ lock-in time. The power consumption is less than 20mW.