• Journal of the Korea Convergence Society
• /
• v.6 no.2
• /
• pp.19-24
• /
• 2015

Nowadays, the number of people who do not move actively or are treated for rehabilitation is increasing because of the disorder or the paralysis of their own lower body by the industrial disaster. In this study, the walker for the people whose bodies are not convenient or the old is investigated. The walkers due to the height of walker are designed and the structural simulation analysis is carried out. The study models of walker are modelled with CATIA program and analyzed with ANSYS program. As the analysis result, the models of 1, 2 and 3 have the maximum stresses extremely below the yield stress of this model and the elastic deformations at these models occurs. Among these models, As the maximum deformation of model 3 has the least value among these models, models 3 is thought to have the best durability. The safety of walker model can be estimated by the basis of the result of this study. The damage can be prevented and the durability is examined by applying this result into the design of walker. And it is possible to be grafted onto the convergence technique at design and show the esthetic sense.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.15 no.10
• /
• pp.5974-5979
• /
• 2014

Lightweight parts with very uniform precision are manufactured by an indent method and the press technique has been improved. Upon assembly with an indent method, a deformation force due to the compressive force occurs between the pin and hole and the contact surface is affected by damage. Therefore, a 3 dimensional model was made using the CATIA program and the damage on the surface contacted with indent was estimated through the ANSYS program in this study. In the analysis result, the maximum load applied at the PCB plate was 21.3 N when the pin goes through the PCB plate. When PCB plate came out of the pin, the maximum load was 19.24 N. As the structural analysis result, the maximum equivalent stress of Pin 1 was 192.96MPa because the maximum stress occurs at Pin 1 among all parts of this study model. By examining the damage property of the contacted indent and applying this study result to the design of real indentation, the damage can be prevented and the durability can be estimated.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.11 no.11
• /
• pp.4100-4107
• /
• 2010

The wrecker truck of lift type is used to move damaged car in accident spot or to move illegal vehicle in towaway zone toward pound.. This special vehicle drives by lifting front or rear side of car with the driving type of towed car. Each car is modelled with CATIA and is simulated with FEM analysis program ANSYS. This study analyzes how dangerous is the triple collision among the wrecker-towed car-driving car as comparing with the usual collision accident with cars. It is studied how responsible is the towed car in case of crashing its back side by driving car. The influence on the driving angle of towed car by lifting wrecker is also considered.

• Journal of the Korea Convergence Society
• /
• v.10 no.11
• /
• pp.321-326
• /
• 2019

As the use of public transportation increases, many researches are being carried out to increase the fuel economy of car. The goal of this study is to design a front body in order to increase the fuel economy of car through three models of cars. All models were designed with CATIA program and the flow analyses on the air outside car by model were carried out with ANSYS program. At the driving speed of 90km/h, the longer the body, the less air resistance it received. So, it is thought that there is the effect to increase fuel economy. Through this study, it can be helpful to design the front car body that can maximize train efficiency. By utilizing the design data on flow analysis according to the position of radiator inside car in this study, the esthetic sense can be given by being grafted onto the real automotive part.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.17 no.4
• /
• pp.56-62
• /
• 2013

The system analysis and design program of the liquid rocket engine has been developed for preliminary conceptual design process. The program analyzes the engine system and obtains optimal design variables by optimization methods such as genetic algorithm for the higher specific impulse and thrust to weight ratio using given input parameters and requirements. For the users' convenience, the GUI has been offered. The 3-dimensional model for the visualization of results has been interconnected with the CATIA program. The results are expected to be applied to the design process of the space launch vehicle for the analysis and selection of the propulsion system.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.20 no.2
• /
• pp.655-661
• /
• 2019

This study examined the change in driving performance according to the starting position of the rear diffuser of a vehicle. To accomplish this, the CATIA 3D design program was used to model the vehicle with reference to a commercial SUV vehicle and design the rear diffuser to start from 300, 400, and 500 mm from the rear tire. The flow and drag change were analyzed and the change in air flow was confirmed using Fluent, a flow analysis program at a vehicle traveling speed of 60, 100, and 140 km/h. The rear diffuser reduced the lift and drag forces compared to no diffuser regardless of the starting position. This is because if there is a rear diffuser, it will reduce the vortex phenomenon by suppressing the flow separation that occurs when air is drawn out from the rear portion of the vehicle. In this study, the starting point SP 400 was determined to be the optimal condition because the lift force was the smallest at SP 400 and the lift reduction effect was the best.

• Journal of the Korea Convergence Society
• /
• v.9 no.11
• /
• pp.271-276
• /
• 2018

When the driver riding in a bicycle goes on board, the load of driver is shown differently according to the position loaded on the frame of bicycle. The load is applied most at the joint of bike frame and the load at the mid-part of frame is applied least than the other parts. So, the weight of frame is decreased as the part not applied with a lot of load is manufactured into the thin thickness. As the part applied with high load is manufactured into the thick thickness, it can be endured through this load. The configurations of general frame, double butted and triple butted were modelled by using CATIA program. The durabilities of each model due to the load of passenger were investigated by carrying the structural and fatigue analyses. As this study result investigated with the analysis program of ANSYS, the deformation of general frame happened most and that of triple butted became least. These simulation analysis data are intended to be used to design the actual bicycle frame in the most efficient way at design and manufacture.

• Journal of the Korea Convergence Society
• /
• v.10 no.7
• /
• pp.149-154
• /
• 2019

This paper is to study the durability through structural analysis on the front undercover of SUV car for offroad. It was investigated which model became structurally best by analyzing three kinds of models which are similar to the configuration of undercover for the protection of the part under car body which has been used really. The models of undercover were designed through CATIA program and analyzed by using ANSYS program as three kinds of models A, B and C. Through the analysis results, model B was expressed to have the best durability as model B has the least equivalent stress and the longest fatigue life among three models. As the design data with the durability of undercover obtained on the basis of this study result are utilized, the esthetic sense can be shown by being grafted onto the machine or structure at real life.

• Journal of the Korea Convergence Society
• /
• v.10 no.9
• /
• pp.187-192
• /
• 2019

In this study, the structural and fatigue analyses were carried out according to the configuration of rear wheel suspension of torsion beam. Three types of models similar to the actual torsional beam suspension are analyzed and we will find out which one is best on strength. The models of torsion beam suspension were designed in three types of models A, B and C through CATIA program and the results of structural and fatigue analyses were obtained by using the ANSYS program. We will confirm which model is better structurally than other models. According to the analysis results, the deformation happens to be the largest in the middle, and model B has the least deformation compared to model A and C. Similarly, model B is shown to have the smallest result at equivalent stress. So, model B is judged to be the best in terms of its strength, and it is thought to be the most efficient to converge into art design at the suspension design with a torsion beam of rear wheel.

• Journal of Advanced Navigation Technology
• /
• v.25 no.1
• /
• pp.40-51
• /
• 2021

In this paper, the design requirements was produced by analyzing domestic and foreign regulations of the vertical takeoff and landing site required to operate the urban air mobility (UAM) system in Korea and the size of the take-off and landing pads were defined, and the configuration of vertiport was proposed. First, for the metropolitan area with high population density, pilot locations of the vertical take-off and landing site were selected based on the demonstration routes suggested by the Ministry of Land, Infrastructure and Transport and analyzed the characteristics of each location and determined the number of possible installations of vertiport by measuring each site. After that, variables necessary for the operation of the vertical takeoff and landing area were set, and the hourly, daily, monthly aircraft operating cycle, the number of acceptable people, and efficiency were calculated according to the number of simultaneous operation and the number of stand. Finally, using CATIA, the configurations of the virtual vertiport was created by applying the design requirements.