• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.18 no.6
• /
• pp.571-575
• /
• 2005

In order to improve the efficiency of dye-sensitized solar cell (DSSC), $TiO_2$ electrode screen-printed on transparent conducting oxide (TCO) substrate was sintered in variation with different temperature$(350\;to\;550^{\circ}C)$. $TiO_2$ electrode on fluorine doped tin oxide (FTO) glass was assembled with Pt counter electrode on FTO glass. I-V properties of DSSCs were measured under solar simulator. Also, effect of sintering temperature on surface morphology of $TiO_2$ films was investigated to understand correlation between its surface morphology and sintering temperature. Such surface morphology was observed by atomic force microscopy (AFM). Below sintering temperature of $500^{\circ}C$, efficiency of DSSCs was relatively lower due to lower open circuit voltage. Oppositely, above sintering temperature of $500^{\circ}C$, efficiency of DSSCs was relatively higher due to higher open circuit voltage. In both cases, lower fill factor (FF) was observed. However, at sintering temperature of $500^{\circ}C$, both efficiency and fill factor of DSSCs were mutually complementary, enhancing highest fill factor and efficiency. Such results can be explained in comparison of surface morphology with schematic diagram of energy states on the $TiO_2$ electrode surface. Consequently, it was considered that optimum sintering temperature of a-terpinol included $TiO_2$ paste is at $500^{\circ}C$.

• Journal of the Korean Applied Science and Technology
• /
• v.26 no.1
• /
• pp.102-108
• /
• 2009

Behaviors of saturated fatty acid halides (CI4, C16, C18) were measured by LB method when the molecules were stimulated by pressure. The saturated fatty acid halides were deposited on the indium tin oxide(lTO) glass by the LB method. The average organic ultra thin film size and the surface roughness of the fatty acid halides thin films were investigated using AFM. It was found that AFM images show small surface roughness ($2.5{\sim}5.0\;nm$) and the organic ultra thin film size of $2.5{\sim}12\;nm$. Both aggregations and pin-holes were also seen on the AFM images. However we found that the surface roughness. These effects seem to be reasonable to be related to the increase of the organic ultra thin film size of fatty acid halides.

• Journal of Magnetics
• /
• v.21 no.2
• /
• pp.159-163
• /
• 2016

Antiferromagnet (AFM)/ferromagnet (FM) bilayer structures are widely used in the magnetic devices of sensor and memory applications, as AFM materials can induce unidirectional anisotropy of the FM material via exchange coupling. The strength of the exchange coupling is known to be sensitive to quality of the interface of the AFM/FM bilayers. In this study, we utilize proton irradiation to modify the interface structures and investigate its effect on the magnetic properties of AFM/FM structures, including the exchange bias and magnetic thermoelectric effect. The magnetic properties of IrMn/CoFeB structures with various IrMn thicknesses are characterized after they are exposed to a proton beam of 3 MeV and $1{\sim}5{\times}10^{14}ions/cm^2$. We observe that the magnetic moment is gradually reduced as the amount of the dose is increased. On the other hand, the exchange bias field and thermoelectric voltage are not significantly affected by proton irradiation. This indicates that proton irradiation has more of an influence on the bulk property of the FM CoFeB layer and less of an effect on the IrMn/CoFeB interface.

• Macromolecular Research
• /
• v.12 no.1
• /
• pp.134-140
• /
• 2004

Semi-crystalline poly(ethylene terephthalate) (PET) film surfaces were modified with argon and oxygen plasmas by radio-frequency (RF) glow discharge at 240 mTorr/40 W; the changes in topography and surface structure were investigated by atomic force microscopy (AFM) in conjunction with specular reflectance of infrared microspectroscopy (IMS). Under our operating conditions, analysis of the AFM images revealed that longer plasma treatment results in significant ablation on the film surface with increasing roughness, regardless of the kind of plasma used. The basic topographies, however, were different depending upon the kind of gas used. The specular reflectance analysis showed that the ablative mechanisms of the argon and oxygen plasma treatments are entirely different with one another. For the Ar-plasma-treated PET surface, no observable difference in the chemical structure was observed before and after plasma treatment. On the other hand, the oxygen-plasma-treated PET surface displays a significant decrease in the number of aliphatic C-H groups. We conclude that a constant removal of material from the PET surface occurs when using the Ar-plasma, whereas preferential etching of aliphatic C-H groups, with respect to, e.g. , carbonyl and ether groups, occurs upon oxygen plasma.

• Korean Journal of Veterinary Research
• /
• v.47 no.4
• /
• pp.389-393
• /
• 2007

In this study, the levels of aflatoxin $M_1$ ($AFM_1$) in milk were determined by HPLC with derivatization method. Milk samples were purified using $C_{18}$ disposable cartridge followed by derivatization with trifluoroacetic acid and analysed using HPLC with fluorescence detection. The recoveries of AFM1 from milk samples added $AFM_1$ at a level of 0.025~0.1 ng/ml were 94.7~98.0% with detection limit of 0.009 ng/ml. The amounts of $AFM_1$ were determined below 0.05 ng/ml for all tested samples of commercial milk collected in 1999 and 2000.

• Journal of Magnetics
• /
• v.16 no.3
• /
• pp.197-200
• /
• 2011

Using the full potential linearized augmented plane wave (FLAPW) method, the influences of uniform and tetragonal strains on the magnetic state have been explored for chemically ordered bulk $L1_2$ $FePt_3$. The ordered state displays antiferromagnetic $Q_1$ (AFM-$Q_1$) state but it transitions into antiferromagnetic $Q_2$ (AFM-$Q_2$) state at about 10% uniform strain. The ferromagnetic (FM) state is observed at 11% uniform strain. For tetragonal strain, it is also seen that the transition from AFM-$Q_1$ to AFM-$Q_2$ depends on the strength and direction of the applied strain. The FM state does not appear in this case. Magnetocrystalline anisotropy (MCA) calculations for tetragonal distortion reveal that the spin reorientation transition occurs. In addition, we find that the direction of magnetization and the magnitude of magnetic anisotropy energy strongly depend on the c/a ratio.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2012.02a
• /
• pp.558-558
• /
• 2012

최근의 원자간력현미경(AFM)은 soft한 생체물질을 비파괴적 방법 및 나노크기의 분해능으로 여러 구조적, 물리적 특성 측정이 가능하여 bio분야에 다양이 활용되고 있다. 본 연구에서는 AFM을 이용하여 줄기세포인 BM MSC(bone marrow mesenchymal stem cell)가 신경세포로 분화 여부를 측정하는 방법을 보고하고자 한다. 신경세포의 신호전달은 시냅스에서 신경전달물질을 매개로 하여 이루어지는데, 신경전달물질 중에 D-Glutamic acid는 시냅스후세포에서 흥분성 전위 크기를 증가시킨 상태를 장기간 유지시켜주는 물질로, 특정물질인 Glutamate와 항원-항체 결합을 한다. 본 연구에서는 이 두 물질간의 항원-항체 반응을 활용하여 줄기세포의 신경세포로 분화 여부를 AFM으로 측정하였다. 먼저, 수용성 시료인 두 물질을 증류수에 용해시켜 Mica 기판에 그 용액을 떨어뜨려 자연건조로 시료를 준비한 후, AFM으로 형태 및 크기를 측정하였다. D-Glutamic acid와 Glutamate는 구형 입자 형태를 보였으며, Glutamate의 너비는 ~100 nm이고, D-Glutamic acid는 ~50 nm였다. 두 물질이 든 용액을 섞었을 때, 항원-항체 반응에 의해 다른 크기의 두 구형입자가 붙어 있는 형태가 관찰되었다. 이 반응을 활용하여, 신경세포에서 분비되는 신경전달물질인 D-Glutamic acid를 선별하였다. DMEM 배지에 신경암세포주인 SH-SY5Y 를 접종한 후 $37.6^{\circ}C$의 incubator에서 24시간 배양하고, 화학적 자극(60~70 mM의 KCl 용액을 주입함)을 주어 신경전달물질 분비를 유도하였다. 그 배지에 항체 Glutamate 를 주입하여 자연건조 시킨 후 항원-항체 결합특성을 AFM으로 측정하여, 항원-항체 결합된 이미지와 동일함을 확인하였다. 결과적으로 AFM을 이용한 신경전달물질의 항원-항체 결합여부 측정을 통해, BM MSC 줄기세포의 신경세포로 분화를 판단할 수 있으며, 이 방법은 줄기세포의 특정 세포로의 분화 여부 판단에 활용될 것으로 기대된다.

• Journal of the Korean Vacuum Society
• /
• v.20 no.4
• /
• pp.252-257
• /
• 2011

The ring formation and electronic properties of furan adsorbed on graphene layers grown on 6H-SiC (0001) has been investigated using atomic force microscopy (AFM), near edge X-ray absorption fine structure (NEXAFS) spectra for the C K-edge, and core level photoemission spectroscopy (CLPES). Moreover, we observed that furan molecules adsorbed on graphene could be used for chemical functionalization via the lone pair electrons of the oxygen group, allowing chemical doping. We also found that furan spontaneously form rings with one of three different bonding configurations and the electronic properties of the ring formed by furan on graphene can be described using by AFM, NEXAFS and CLPES, respectively.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.28 no.9
• /
• pp.598-601
• /
• 2015

The $Sr_{0.7}Bi_{2.3}Nb_2O_9(SBN)$ thin films are deposited on Pt electrode($Pt/Ti/SiO_2/Si$) using RF sputtering method at various deposition temperature. The deposition temperature of optimum was $300^{\circ}C$. SBN thin films were annealed at $500{\sim}700^{\circ}C$ using furnace and RTA, respectively. The surface roughness showed about 2.42 nm in annealing temperature($600^{\circ}C$) of furnace. The capacitance density of SBN thin films were increased with the increase of annealing temperature. The maximum capacitance density of $0.7{\mu}F/cm^2$ was obtained by annealing temperature($700^{\circ}C$). The frequency dependence of dielectric loss showed about 0.03 in frequency ranges of 1~1,000 kHz.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2012.02a
• /
• pp.278-278
• /
• 2012

최근 폴리이미드(Polyimide) 고분자 물질을 기판으로 하는 플렉시블 전자소자 구현에 관한 연구가 활발히 진행 되고 있다. 폴리이미드는 수분 흡수율이 1% 이하인 소수성 물질로서 폴리이미드 기판 위 전극 형성에 있어 전극 물질이 분리되는 현상이 발생하게 된다. 따라서 본 연구에서는 소수성의 표면 성질을 갖는 폴리이미드 기판의 Asher 처리를 통한 표면 최적화에 대한 실험을 진행하였다. 유리기판 위에 액상 폴리이미드를 ${\sim}10{\mu}m$ 두께로 Spin coating 한 후 $120^{\circ}C$ hot plate에서의 soft bake와 $200^{\circ}C$, $320^{\circ}C$의 furnace에서의 단계적 cure 과정을 통해 표면의 defect을 최소화하였다. Microwave Asher 장비를 이용하여 폴리이미드 막에 10초, 15초, 20초 동안 asher 처리를 한 후 Atomic Force Microscopy (AFM) 장비로 시간에 따른 폴리이미드 기판 표면의 변화를 확인하였다. AFM 확인 결과 10 초의 공정 조건에서 가장 우수한 표면 morphology를 보였으며, 이는 표면의 탄소와 이물질을 제거하기 위해 사용되는 asher 처리 시간이 상대적으로 증가함에 따라 폴리이미드 막의 탄소 성분이 제거 되면서 표면의 형상이 최적화 이상으로 변화하기 때문이다. 본 실험은 폴리이미드를 기반으로 하는 플렉시블 전자소자 구현에 있어 전극 및 소자 제작에 크게 기여할 것으로 판단된다.