• Nuclear Engineering and Technology
• /
• v.53 no.7
• /
• pp.2312-2322
• /
• 2021

In recent studies, the creep rate of Zircaloy-4, one of the basic property parameters of the nuclear fuel code, has been commonly used with the axial creep model proposed by Rosinger et al. However, in order to calculate the circumferential deformation of the fuel cladding, there is a limitation that a difference occurs depending on the anisotropic coefficients used in deriving the circumferential creep equation by using the axial creep equation. Therefore, in this study, the existing axial creep law and the derived circumferential creep results were analyzed through a circumferential creep test by the internal pressurization method in the isothermal conditions. The circumferential creep deformation was measured through the optical image analysis method, and the results of the experiment were investigated through constructed IDECA (In-situ DEformation Calculation Algorithm based on creep) code. First, preliminary tests were performed in the isotropic β-phase. Subsequently in the anisotropic α-phase, the correlations obtained from a series of circumferential creep tests were compared with the axial creep equation, and optimized anisotropic coefficients were proposed based on the performed circumferential creep results. Finally, the IDECA prediction results using optimized anisotropic coefficients based on creep tests were validated through tube burst tests in transient conditions.

• Journal of Advanced Navigation Technology
• /
• v.13 no.3
• /
• pp.337-343
• /
• 2009

In this paper, we proposed a burst mode symbol timing recovery unit that is applicable to the VDL Mode-2 using D8PSK modulation. A method that IIR loop filter is used to minimize symbol timing error is hard to apply to burst mode because its convergence time is long. That is, the fast convergence property is important. In this paper, the proposed method takes one sample which has maximum symbol power after the initial synchronization has been achieved by using preambles. The main principle of operation is that the unit moves one sample clock to advance or retard according to symbol power. We verify that the proposed method is operated well in ${\pm}100$ ppm or greater through the test results between Australia ADS Corp. transmitter and the designed receiver.

• Journal of the Korea Institute of Military Science and Technology
• /
• v.20 no.4
• /
• pp.497-504
• /
• 2017

This paper proposes a method to measure the airburst height by utilizing a high speed camera. This method might be applied to the test of which flight target is alive after the burst. The proposed method consists of four main steps. The first step is to compute the impact point using the sea surface height. The second step is to compute the height of burst (HOB) by using the distance from the camera to the impact point. This could be different from the real explosion height. That is because the distance from the camera to the burst point is not the same as it from the camera to the impact point. Therefore, the third step is to calculate the approach angle of the flight target with respect to the installed camera. Then, the last step is to compensate the computed height by using the approach angle. The result of the proposed method is compared with it from the triangulation. In this paper, the HOB error is also analyzed regarding the approach angle difference. Based on this analysis, the camera position might be suggested for error reduction.

• Journal of Aerospace System Engineering
• /
• v.7 no.2
• /
• pp.55-59
• /
• 2013

Before avionics equipment are installed in aircraft, several environmental tests such as temperature, vibration, lightning, fire etc. must be conducted. One of the environmental tests is to substantiate protection designs of lightning indirect effect. It can be showed through RTCA DO-160G, section22 "Lightning Induced Transient Susceptibility" test. An additional test of aircraft level is required as well after installation of avionics equipment.

• The Journal of the Institute of Internet, Broadcasting and Communication
• /
• v.12 no.2
• /
• pp.167-174
• /
• 2012

The circuits including with Optical transceiver and clock data recovery, in this paper, SERDES (SERializer-DESerializer) are implemented to construct a GE-PON burst-mode transceiver supporting IEEE 802.3ah and a jig for measuring the burst-mode characteristics, that is to say, PON upstream optical transmission environment are manufactured to evaluate the performance of transceiver. we verified that the limiting amplifier compensated the gap of max. 26dB optical power by experiments. The startup acquisition lock time is 670ns in case of using VSC7123 and 2300ns in case of S2060 and the data acquisition lock time were measured to be 400ns and 600ns, respectively, in the upstream channel transmission in this work. While on the other, VSC7123 is satisfied with IEEE802.3ah recommendations.

• Journal of the Korean Society of Physical Medicine
• /
• v.11 no.2
• /
• pp.1-11
• /
• 2016

PURPOSE: This study was conducted to assess the effects of local vibration on ankle plantarflexion spasticity and clonus in patients with spinal cord injury. METHODS: The subjects were 14 inpatients with complete or incomplete spinal cord injury (SCI) whose scores were higher than 1 on the Modified Ashworth Scale (MAS) and Spinal Cord Assessment Tool for Spastic Reflexes (SCATS) scale of paraplegia. A randomized single-blind cross-over design was used. Vibration treatment involved a single application of vibration for 10 min in the sitting position, and placebo treatment involved the patient remaining in the sitting position for 10 min. One day after treatment, vibration and placebo treatments were crossed over. Spasticity was measured by using the MAS, and resistance force, by using a hand-held dynamometer; clonus was gauged by using the SCATS scale and clonus burst duration. Additionally, the burst maximal frequency and voluntary ankle dorsiflexion angle of the triceps surae were measured. RESULTS: The application of vibration treatment in the sitting position significantly reduced the MAS scores and resistance force, but significantly increased the dorsiflexion angle of the ankle joint (p<0.05). Furthermore, the vibration treatment diminished the clonus burst duration and SCATS score significantly (p<0.05). Although it reduced the burst maximal frequency of the lateral gastrocnemius and medial soleus, this was significant only for the lateral gastrocnemius. The placebo treatment did not significantly affect any of the test parameters. CONCLUSION: Vibration treatment in the sitting position was effective in cases of spasticity and clonus caused by SCI.

• Journal of The Institute of Information and Telecommunication Facilities Engineering
• /
• v.4 no.2
• /
• pp.29-36
• /
• 2005

All-optical fiber-type $2{\times}32$ splitters for an Ethernet PON (passive optical network) were fabricated by using a FBT (fiber biconical tapered) process and the performance of the splitters was tested in upstream transmission of the EPON system. The $2{\times}32$ splitters was obtained by cascading $1{\times}4$ splitters fabricated by a conventional FBT process and showed -18 dB of insertion loss with 1.5 dB uniformity of output power at each channel and -0.1 dB of polarization dependent loss. The insertion loss variation was below 0.1 dB at the temperature range of $-40^{\circ}C\;to\;80^{\circ}C$. For upstream channel transmission test in the EPON system were a Zig board and a burst mode receiver. Zenko-made optical module was used for the burst mode receiver by adding functions of serializer/deserializer and clock data recovery, a Virtex II pro20 chipset and Vitesse VSC7123 were used in the Zig board for characterizing the burst mode and in the clock data recovery chipset, respectively. Startup acquisition lock time and data acquisition lock time were measured to be 670ns and 400ns, respectively, in the upstream channel transmission of the EPON system adapting the $2{\times}32$ splitter fabricated in this work.

• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.16 no.5
• /
• pp.13-18
• /
• 2017

In this work the augmented safety of Type 4 composite vessel in accordance with uniform-stress design has been demonstrated through a series of burst tests and structural analyses. For this end, three sample vessels were used: (1) designed as guided by the isotensoid dome theory (called iso-dome cylinder); (2) with dome longer compared to uniform-stress design (called prolate cylinder); and (3) with dome wider than uniform-stress design (called oblate cylinder). Structural analyses have been performed using ABAQUS finite element code based on the periodic symmetry to circumferential direction. As a result, the maximum stresses are induced around the bodies of all three cylinders. However, the analyses, with the assumption of possible defect demonstrate that the maximum stresses are induced around the dome knuckles for the prolate and the oblate cylinders. The results of the burst tests for the three cylinders show that the burst initiates from the cylinder body of the iso-dome cylinder and from the dome knuckles of the prolate and the oblate cylinders. Finally, it is recommended that, to comply with DOT CFFC 2007, the dome shape should be designed and fabricated as guided by the isotensoid dome theory.

• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2014.10a
• /
• pp.291-292
• /
• 2014

High-speed video transmission modes of master bridge IC are implemented, which supports MIPI (Mobile Industry Processor Interface) DSI (Display Serial Interface) standard. MIPI DSI master bridge IC sends RGB data and various commands to display module (slave) in order to test it. The master bridge IC consists of buffers storing video data of two lines, packet generation block, and D-PHY layer that distributes packets to data lanes and transmits them to slave. In addition, it supports four bpp (bit per pixel) formats and three transmission modes including Burst and Non-Burst (Sync Events, Sync Pulses types). The designed bridge IC is verified by RTL simulations showing that it functions correctly for various operating parameters.

• Korean Journal of Audiology
• /
• v.24 no.1
• /
• pp.35-39
• /
• 2020

Background and Objectives: The cortical auditory evoked potential (CAEP) is a useful objective test for diagnosing hearing loss and auditory disorders. Prior to its clinical applications in the pediatric population, the possible influences of fundamental variables on the CAEP should be studied. The aim of the present study was to determine the effects of age and type of stimulus on the CAEP waveforms. Subjects and Methods: Thirty-five healthy Malaysian children aged 4 to 12 years participated in this repeated-measures study. The CAEP waveforms were recorded from each child using a 1 kHz tone burst and the speech syllable /ba/. Latencies and amplitudes of P1, N1, and P2 peaks were analyzed accordingly. Results: Significant negative correlations were found between age and speech-evoked CAEP latency for each peak (p<0.05). However, no significant correlations were found between age and tone-evoked CAEP amplitudes and latencies (p>0.05). The speech syllable /ba/ produced a higher mean P1 amplitude than the 1 kHz tone burst (p=0.001). Conclusions: The CAEP latencies recorded with the speech syllable became shorter with age. While both tone-burst and speech stimuli were appropriate for recording the CAEP, significantly bigger amplitudes were found in speech-evoked CAEP. The preliminary normative CAEP data provided in the present study may be beneficial for clinical and research applications in Malaysian children.