• 전기학회논문지
• /
• 제57권10호
• /
• pp.1790-1795
• /
• 2008

Energy scavenging is a technique that converts ambient energy, for example, vibration and light, to electrical energy in order to supply power to low power electronic devices such as ubiquitous sensors. In this paper, we propose an optimal operation condition of power delivery circuit and design strategy for energy scavenging system in which the generated power is order of microwatt and, consequently, efficient handling of power is critical. We also propose that high data transmission rate is more realistic optimal design objective rather than high energy efficiency. It is shown that disconnection of load from the storage capacitor right after data transmission reduces energy wasting and that optimal value of storage capacitor can be determined at this condition. The feasibility of our propose is proved by experiments and we believe that the proposed design strategy will promote the application of piezoelectric micropower generator to the ubiquitous sensor networks.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2007년도 춘계학술대회 논문집 전기기기 및 에너지변환시스템부문
• /
• pp.103-106
• /
• 2007

This paper presents single-phase SRM drive system with single-stage high power factor and low torque ripple. Single-phase SRM has simple mechanical and electrical structure, robust and high speed operation characteristic. But conventional SRM drive with diode bridge rectifier and filter capacitor has a low power factor because of short charge time of capacitor. Therefore, this paper presents a novel single-phase SRM drive with single-stage structure circuit, which can improve the power factor and reduce peak torque ripple. A novel switching topology is presented base on mathematical analysis. The novel drive method is verified by simulations and experiments.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2007년도 추계학술대회 논문집 전기기기 및 에너지변환시스템부문
• /
• pp.151-153
• /
• 2007

In this paper, the control method of extracting maximum power from the seaflow energy is proposed. This system consists of buck-boost converter, bridge diode. The control is performed by using the variable duty ratio control of buck-boost converter. For extracting maximum power, it is necessary to know the seaflow turbine's maximum power curve and the seaflow speed measurement. But this makes the system difficult and expensive to implement. So this paper proposes the MPPT control method where the seaflow speed and the maximum power curve of the seaflow turbine are not required. The effectiveness of algorithm is simulated based on Matlab $Simulink^{(R)}$.

• 전력전자학회:학술대회논문집
• /
• 전력전자학회 2004년도 전력전자학술대회 논문집(2)
• /
• pp.704-708
• /
• 2004

Recently, many nation have released standard such as IEC 61000-3-2 and IEEE 59, which impose a limit on the harmonic current drawn by equipment connected to AC line in order to prevent the distortion of an AC Line. Therefore, Plasma Display Panel (PDP) which is highlightened in digital display device also has the Power Factor Correction (PFC) circuit to meet the harmonic requirements. In PDP power module, the conventional boost converter is usually used for the PFC circuit. However, it comes serious thermal problem on it's bridge diode due to heat of PDP, and therefore the system stability is not guaranteed. In this paper, the bridgeless boost converter, which is used for PFC circuit of the PDP power module, is designed and verified the possibility of the application in a practical product in a view of efficiency, component count, temperature and etc.

• 전력전자학회:학술대회논문집
• /
• 전력전자학회 2008년도 하계학술대회 논문집
• /
• pp.256-258
• /
• 2008

현재 멀티레벨 인버터는 고압 대용량 시스템에 많이 사용되고 있으며, 연구 또한 지속되고 있다. 현재 일반적으로 사용되는 멀티레벨 방법으로는 Neutral Point Clamp(NPC), H-Bridge 케스캐이드, 플라잉 커패시터가 멀티레벨이 있다. 본 논문에서는 Neutral Point Clamp 토포로지 중 다이오드 클램프 멀티레벨을 이용하여 3상 유도전동기용 하이브리드 다이오드 클램프 멀티레벨 인버터를 구성 하였다. 그리고 신호 발생 방법으로는 Subhamonic PWM 방식을 사용하였으며, 유도 전동기 제어는 간접벡터제어로 제어를 함으로써 유도 전동기 구동용 하이브리드 다이오드 클램프 멀티레벨 인버터의 적합함을 검증 하였다.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2001년도 하계학술대회 논문집 B
• /
• pp.1110-1112
• /
• 2001

This paper presents a high frequency electronic ballast with high efficiency and high power factor. The proposed ballast have driven by the half bridge inverter which is linked diode rectifier without DC link capacitor. Minimized elements of circuit configurations can make the efficiency of the ballast increase. High input power factor which is up to 0.96 can be achieved and the crest factor of lamp current waveforms is controlled with below 1.75 by using a novel control scheme which has PFM and PWM methods simultaneously. In this paper, the circuit configurations of the proposed ballast and the control schemes are described. The usefulness of the proposed ballast is confirmed with the simulation results.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2001년도 하계학술대회 논문집 B
• /
• pp.1281-1283
• /
• 2001

An investigation into power conditioners that interface with photovoltaic array and utilities has been completed. The rating for this investigation is residential system(3-5kW) that interface with a 220V single phase utility connection. As the result of this investigation, a 3kW high frequency PWM IGBT inverter feeding a high frequency isolation transformer with a sinusoidal current wave was selected. The output of the transformer rectified with a diode bridge rectifier four IGBT, used as 60Hz switched, reverse the polarity of the rectified current on every other half cycle of the utility voltage. Even though the high frequency link system used more power semiconductors a net size, weight, and parts cost saying result compared to the other systems due to elimination of 60Hz transformer.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2001년도 하계학술대회 논문집 B
• /
• pp.1129-1131
• /
• 2001

A new low cost single stage high power factor electronic ballast for fluorescent lamps is presented in this paper. The proposed topology is based on integration of two-boost converter and LC type high frequency resonant converter. A ballast is obtained by simple construction, because full bridge rectifier diode is eliminated and simple control circuits is applied. Using two boost converter operating positive and negative half cycle respectively at line frequency (60Hz), operating in discontinuous conduction mode performs high power factor. The simulated and experimental results for 64W fluorescent lamps operating at 45kHz switching frequency and 110V line voltage have been obtained.

• 전력전자학회:학술대회논문집
• /
• 전력전자학회 1999년도 전력전자학술대회 논문집
• /
• pp.663-666
• /
• 1999

This paper describes a three-phase converter with high power factor using a scheme of discontinuous current mode(DCM). The proposed system can replace the conventional diode bridge with step-up chopper which is used as a converter for adjustable speed drive. In this system, the current of reactor is zero at turn-on instance because of operation in DCM, while the switch turns off at the instance of maximum current. A soft-switching scheme with lossless snubber was proposed. Therefore, a zero-voltage switching at turn off can be achived by lossless snubber and zero-current switching at turn on can be obtained by operating under DCM. A theoretical analysis and computer simulations with PSpice were done to verify the operation of the proposed system. Also a prototype of hardware system was built and tested for verifying the feasibility of proposed system.

• 전력전자학회논문지
• /
• 제20권1호
• /
• pp.59-64
• /
• 2015

This paper proposes an analysis and operation strategy of a grid-connected wind turbine system using a diode rectifier. The currents of generators are the same as that of a small wind turbine system. Therefore, the analysis of generator torque is required as opposed to an analysis of blade speed. In this paper, the appropriate MPPT control method is proposed to control generator torque. Usefulness of the proposed operation strategy is verified by simulations and experiments.