• 한국농공학회지
• /
• 제40권5호
• /
• pp.80-90
• /
• 1998

The EPS construction method-one kind of the load reducing methods-utilizes the EPS blocks, ultra-light materials whose unit weight is about 1/100 of soils and has been applied to many soft ground sites. It needed 3,000 days to get the 90% degree of the consolidation for the case of 12m high soil embankments on the 30m thick soft clayey foundations. The N value of SPT at this deposit was less than 5. The pack drain was installed to promote the radial consolidations. Although staged embankments were planned, designers failed to get a sufficient stability of the foundation ground. Therefore, the EPS fill method was selected to reduce the load and the construction period. EPS blocks(D-20 model) replaced the upper part of the soil embankments. These complex embankments reduced the ground settlement and the construction period. The possibility of lateral movements of the bridge abutments was checked and the design scheme was reviewed.

• 한국지반공학회논문집
• /
• 제17권4호
• /
• pp.199-208
• /
• 2001

본 연구의 목적은 교대가 설치된 지반의 사면안전율과 교대측방변위의 관계를 분석하여 교대의 측방이동 판정기준을 마련하고자 함에 있다. 이를 위하여 국내의 연약지반에 설치된 30개 교대의 측방이동사례를 조사하고, SLOPILE (Ver 2.0)프로그램을 이용하여 교대의 측방변위와 교대기초말뚝의 사면안정효과를 고려한 사면안정해석을 실시한다. 해석결과 교대기초말뚝의 실측측방변위를 고려할 경우 1.8이상 되어야 한다. 또한, 교대기초말뚝의 허용측방변위량에 따른 사면안정 해석결과, 교대의 허용측방변위가 작게 규정될수록 사면안정성에 기여하는 말뚝의 효과는 감소하고 있음을 알 수 있다.

• 한국지반공학회논문집
• /
• 제17권4호
• /
• pp.269-278
• /
• 2001

국내 30개의 교대측방이동 사례현장에 대하여 교대기초말뚝의 사면안정효과와 교대의 실측측방변위를 고려한 사면안정해석을 실시하였다. 해석결과 사면안전율은 말뚝의 효과를 무시한 경우 1.5이상, 말뚤의 효과를 고려한 경우 1.8이상 되어야 안전함을 알 수 있다. 그리고, 교대의 실측측방변위와 사면안전율과의 상관관계로부터 교대의 허용측방변위 설계기준은 5cm보다 1.5cm로 함이 더 합리적임을 알 수 있다. 사면안정해석결과와 교대의 실측측방변위를 토대로 기존에 제안된 교대측방이동 판정기준의 국내 적용여부를 검토한다. 이를 위하여 교대의 사면안정해석결과 및 실측측방변위와 교대측방이동 관련지수와의 상관관계를 조사한다. 그 결과 실측된 교대의 측방변위와 이를 고려한 사면안전율은 교대의 측방유동지수, 측방이동판정지수 및 지반의 안정계수와 무관한 경우도 많이 존재하는 것으로 나타났다. 이는 결국 이들 경험적인 지수만으로 교대측방이동을 판정하는 것은 불충분함을 의미한다. 따라서, 교대측방이동을 판정할 경우에는 반드시 교대의 측방변위를 고려한 사면안정해석이 실시되어야 한다.

• 한국BIM학회 논문집
• /
• 제10권4호
• /
• pp.40-49
• /
• 2020

This report describes the development of a program that can be linked to an alignment and extracts related information using a prefab structured digital engineering model. The subject bridge was set as a straight alignment, the Superstructure type as Precast girder and the Substructure type as Precast pier and Cast-in-situ Abutment. We identified the variables required to create a digital engineering model and reviewed them to create the digital engineering model by entering them as numerical values in the program. In addition, it is configured so that the variables linked to the alignment can be entered numerically. The quantity takeoff can be calculated when the design is complete. The purpose of the program development presented in this report is to enable the designers to select the optimal alternative by designing a bridge that best fits their current situation, extracting the relevant information and then by providing it to the manufacturer and construction company.

• Journal of Korean Dental Science
• /
• 제15권1호
• /
• pp.92-99
• /
• 2022

This case report describes the immediate loading of narrow diameter implants in the mandibular incisor area using full-digital flow. The 3-dimensional position of the implants was planned using digital software, and the corresponding surgical template was fabricated. The implants were inserted immediately after extraction and on the same day, the interim abutment and bridge were placed. At 8 weeks after surgery, the stability of the implants was measured and a digital impression was made using a scan body. Customized titanium abutments and a cement-type full zirconia bridge were delivered. At 36 weeks' follow-up, no clinical or radiographic complications were detected, and the patient was satisfied with the results.

• Steel and Composite Structures
• /
• 제20권4호
• /
• pp.731-748
• /
• 2016

Pile-to-pilecap connection performance is important as Integral abutment bridges (IABs) have no expansion joints and their flexible weak-axis oriented supporting piles take the role of the expansion joint. This connection may govern the bridge strength and the performance against various lateral loads. The intention of this study is to identify crack propagation patterns when the pile-to-pilecap connection is subjected to lateral loadings and to propose novel connections for improved performance under lateral loadings. In this study, eight different types of connections were developed and modeled, using Abaqus 6.12 to evaluate performances. Three types were developed by strengthening the connections using rebar or steel tube: (i) PennDOT specification; (ii) Spiral rebar; and (iii) HSS tube. Other types were developed by softening the connections using shape modifications: (i) cylindrical hole; (ii) reduced flange; (iii) removed flange; (iv) extended hole; and (v) slot hole connection types. The connections using the PennDOT specification, HSS tube, and cylindrical hole were shown to be ineffective in the prevention of cracks, resulting in lower structural capacities under the lateral load compared to other types. The other developed connections successfully delayed or arrested the concrete crack initiations and propagations. Among the successful connection types, the spiral rebar connection allowed a relatively larger reaction force, which can damage the superstructure of the IABs. Other softened connections performed better in terms of minimized reaction forces and crack prevention.

• Computers and Concrete
• /
• 제18권5호
• /
• pp.1041-1051
• /
• 2016

In this study, the construction of a reinforced concrete bridge pier was analyzed from durability point of view. The goal of the study is to analyze the crack iniation condition due to construction and present some recommendations for construction conditions of the reinforced concrete bridge pier. The bridge is located at the western port area of Shenzhen, where the climate is high temperature and humidity. To control the cracking of concrete, a construction simulation was carried out for a heat transfer problem as well as a thermal stress problem. A shrinkage model for heat produced due to cement hydration and a Burger constitutive model to simulate the creep effect are used. The modelling based on Femmasse(C) is verified by comparing with the testing results of a real underground abutment. For the bridge pier, the temperature and stress distribution, as well as their evolution with time are shown. To simulate the construction condition, four initial concrete temperatures ($5^{\circ}C$, $10^{\circ}C$, $15^{\circ}C$, $20^{\circ}C$) and three demoulding time tips (48h, 72h, 96h) are investigated. From the results, it is concluded that a high initial concrete temperature could result in a high extreme internal temperature, which causes the early peak temperature and the larger principle stresses. The demoulding time seems to be less important for the chosen study cases. Currently used 72 hours in the construction practice may be a reasonable choice.

• 대한치과보철학회지
• /
• 제43권5호
• /
• pp.611-621
• /
• 2005

State of problem: Zirconia all-ceramic restoration fabricated with CAM system is on an increasing trend in dentistry. However, evaluation of the marginal and internal fits of zirconia bridge seldomly have been reported. Purpose: This study was to evaluate the at of margin and internal surface in posterior 3-unit zirconia bridge framework fabricated with CAM system(DeguDent, Germany). Material and Method: Preparations of secondary premolar and secondary molar on artificial resin model were performed for fabrication of 3-unit posterior bridge framework. Fits of 5 zirconia bridge framework were compared with 5 precious ceramo-metal alloy framework(V-GnathosPlus, Metalor, Switzerland), and prepared margins were designed to chamfer and shoulder finishing line. Each framework was cemented to epoxy resin model with reinforced glass ionomer(FujiCEM, GC Co., Japan), embedded in acrylic resin and sectioned in two planes, mesio-distal and buccolingual. Samples were divided into six pieces by sectioning and had two pieces of each surface(i.e mesial, distal, buccal and lingual surface) per abutment, so there were eight measuring points in each abutment. External gap was measured at the margin and internal gaps were measured at the margin, axial and occlusal surface. Gaps were observed under the measuring microscope(Compact measuring microscope STM5; Olympus, Japan) at a magnification of $\times100$. T-test were used to determine the statistic significance of the different gaps between zirconia and metal framework. Results and Conclusion: 1. External and internal marginal gaps of zirconia and metal framework were in clinically acceptable range. External marginal gaps were not different significantly between zirconia$(81.9{\mu}m)$ and metal $(81.3{\mu}m)$ framework and internal marginal gaps of zirconia $(44.6{\mu}m)$ were smaller than those of metal framework $(58.6{\mu}m)$. 2. Internal axial gaps of zirconia framework$(96.7{\mu}m)$ were larger than those of metal frame-work$(78.1{\mu}m)$ significantly and adversely, internal occlusal gaps of zirconia frame-work$(89.4{\mu}m)$ were smaller than those of metal framework $(104.9{\mu}m)$ significantly. 3. There were no significant differences in external and internal marginal gaps between chamfer and shoulder finish line when zirconia frameworks were fabricated.

• Geomechanics and Engineering
• /
• 제2권2호
• /
• pp.125-140
• /
• 2010

Slope stability analysis of the right abutment of a railway bridge proposed at about 350 m above the ground level, crossing a river and connecting two huge hillocks in the Himalayas, India is presented in this paper. The site is located in a highly active seismic zone. The rock slopes are intensely jointed and the joint spacing and orientation are varying at different locations. Static slope stability of the rock slope is studied using equivalent continuum approach through the most commonly used commercial numerical tools like FLAC and SLOPE/W of GEOSTUDIO. The factor of safety for the slope under static conditions was 1.88 and it was reduced by 46% with the application of earthquake loads in pseudo-static analysis. The results obtained from the slope stability analyses confirmed the global stability of the slope. However, it is very likely that there could be possibility of wedge failures at some of the pier locations. This paper also presents the results from kinematics of right abutment slope for the wedge failure analysis based on stereographic projections. Based on the kinematics, it is recommended to flatten the slope from 50o to 43o to avoid wedge failures at all pier locations.

• 한국산학기술학회논문지
• /
• 제20권4호
• /
• pp.534-544
• /
• 2019

IPM Bridge는 파일벤트가 지표면으로부터 돌출되어, 교대의 과도한 변위가 유발될 수 있다. 본 연구에 사용된 교량의 형상은 IPM Bridge의 설계지침에 제시된 최대 적용 조건인 경간 120.0m, 사각 30도, 파일벤트의 돌출높이 최대 10.0m를 적용하였다. 이 교량모델을 이용하여, IPM Bridge의 최대 경간 적용조건에 따른 최대 변위를 산정하였으며, Bozozuk가 제시한 허용 변위에 근거하여 IPM Bridge의 수평변위의 안정성을 검토하였다. IPM Bridge의 최대 수평변위는 여름철의 팽창 조건보다는 겨울철의 수축 조건에서 더 크게 산정되었으며, 수평변위는 사각보다는 교량의 길이에 더 큰 영향을 받는 것으로 나타났다. 그리고 수직 변위는 사각과 연장에 큰 영향을 받지 않는 것으로 나타났다. 경간의 증가에 따라 수평변위가 크게 증가되었으며, 연장 120.0m에서의 수평변위는 Bozozuk가 제시한 허용 변위를 초과하는 것으로 나타났다. 하지만, 파일벤트에 발생되는 모멘트가 소성모멘트를 초과하지는 않았다. IPM Bridge는 설계지침에 제시된 최대 적용조건인 파일벤트의 돌출높이 10.0m, 연장 120.0m에서는 수평변위가 과도하게 발생될 수 있으므로, 설계단계에서 면밀한 검토가 필요하다.