• The Journal of the Korea institute of electronic communication sciences
• /
• v.9 no.10
• /
• pp.1111-1116
• /
• 2014

In this paper, in order to improve performance of LDPC codes, we propose an effective algorithm with lowering error floor of LDPC codes. This method is done by breaking trapping sets, mostly caused by an undesirable structure. This algorithm is not need to observe all the errors, only need to break the trapping sets, to effect the effectiveness. Simulation results show that its performance can be significantly improved with this decoding algorithm.

• KSBB Journal
• /
• v.17 no.3
• /
• pp.311-313
• /
• 2002

Lactobacillus spry. are Gram-positive bacteria playing important roles in human health. In this study, we successfully isolated the total RNA from the cells broken by glass beads using hot phenol method. Moreover, we were able to omit lysozyme and proteinase K treatment by using glass beads to break cell more efficiently. This method was more rapid and simple when compared to the previous one. Prepared RNA can be used for the transcriptional analysis of Lactobacillus spp.

• Proceedings of the Korea Institute of Fire Science and Engineering Conference
• /
• 2007.11a
• /
• pp.205-210
• /
• 2007

This study on the prevention of electric fire. Generally the electric fire is caused by break or disconnection of the power line, short circuit and poor contact, arcing fault ect. In these causes, this paper is studied on the detection of poor contact and arcing fault. The arcing fault is caused by poor contact mainly. The arcing fault can occurs a electric fire by interaction of flammable gas and materials and it can be caused of tracking and carbonization. These phenomenons is also caused of electric fire. Therefore this paper is studied on the detection of arcing fault and poor contact.

• Journal of the Korea Institute of Military Science and Technology
• /
• v.10 no.1
• /
• pp.5-13
• /
• 2007

The trajectory of an current artillery munition is subject to a variety of different error sources resulting in more or less big deviation from the nominal predicted flight path. The 1D CCM(Course Correction Munition) has appeared to solve this problem and the mechanism of 1D CCM is a simple and low cost one using the influence of drag to range behavior of an artillery munition. In the paper 1D CCM concept has been simulated using wind tunnel experiment results of the specified Korean munition with CCF(Course Correction Fuze) and calculated the performance of its rang error reduction. From the simulated results it can be numerically explained that the possibility of adaptation of 1D CCM concept to Korean artillery munitions.

• Nuclear Engineering and Technology
• /
• v.37 no.5
• /
• pp.469-478
• /
• 2005

The subchannel analysis capability of MARS, a multi-dimensional thermal-hydraulic system code, has been enhanced. In particular, the turbulent mixing and void drift models for the flow-mixing phenomena in rod bundles were improved. Then, the subchannel analysis feature was combined with the existing coupled system thermal-hydraulics (T/H) and 3D reactor kinetics calculation capability of MARS. These features allow for more realistic simulations of both the hot channel behavior and the global system T/H behavior. Using the coupled features of MARS, a coupled analysis of a main steam line break (MSLB) is carried out for demonstration purposes. The results of the calculations are very reasonable and promising.

• Proceedings of the KIEE Conference
• /
• 2000.11c
• /
• pp.550-552
• /
• 2000

Treeing inhibitors are added in XLPE matrix to investigate the effect on electrical properties of XLPE. The treeing inhibitors are barbituric acid, 4- (4-Nitrophenylazo) resorcinol and 4-(4-Nitrophenylazo) naphthol. Added amount of each treeing inhibitors were varied form 0phr to 2.0phr. In order to know the changes of electrical properties, break down strength, $tan{\delta}$, and ${\varepsilon}_r$ were measured. Experimental results showed that electrical properties of each sample was slightly changed by amount of additives.

• Proceedings of the KIEE Conference
• /
• 2008.11a
• /
• pp.119-121
• /
• 2008

In underground power cable system, the device for limiting over-voltage is needed when transient over-voltage break out between sheath and ground. For this reason, the SVL(Sheath Voltage Limiter) has been applied on weak points. But the broken SVLs which are installed on the single point bonding system on underground cable are frequently found. In this paper, EMTP(Electromagnetic Transient Program) is utilized to analyze effects on the installation methodology of the parallel ground conductor and SVL for the single point bonding system on the underground cable. The result shows that the proposed installation methodology can be applied for single point bonding system and contribute for power system stabilization.

• IE interfaces
• /
• v.12 no.4
• /
• pp.567-574
• /
• 1999

The use of POP(Point of Production) systems which help to report the realtime production information to the supervisor class and to send commands to the shop floor is increasing gradually. Future companies will need to break the limit of regions and to exchange information among remote-sited departments and companies located abroad. In order to achieve this goal, Internet which is growing remarkably nowadays will be the best tool. In this research, a prototype of the POP system based on Internet is developed using the Java language. The developed POP system can monitor production status by collecting information from shop floor through a web server and can control production equipments from remote sites.

• Korean Institute of Interior Design Journal
• /
• no.38
• /
• pp.48-56
• /
• 2003

This study is purposed to find the transition of the perspective connected with visual modality. The perspective based on Greek optics and euclidean geometry and rediscovered in Renaissance represents the object according to the particular moment and the point of view, is a principal fact which affect architecture, the form of a city and the spatial organization and symbolizes an ideal of the times. It embodied perception which treats the space rationally on the basis of realism and became visual modality based on the separation of the seeing subject and the world of the object. The point of view became one with the vanishing point which made up the shape and after Renaissance for four hundred years a straight line, a right angle and a circle got to be favorite geometrical choices in architecture. A fixed point of view of the subject is getting to change and break up fundamentally by the new visual technologies of the modem times.

• Transactions of the Korean Society of Machine Tool Engineers
• /
• v.10 no.3
• /
• pp.75-82
• /
• 2001

The continuous chip in turning operation deteriorates the precision of workpiece and can cause a hazardous condition to operator. Thus the chip form becomes a very important task for reliable turning process. The chip form is identified using the neural network of supervise data Through the measurement of energy radiated from the chip. The feed mechanism os adjusted in order to break continuous chip according to the result of the chip form recognition and it shows a good approach for precision turning operation.