• 한국복합재료학회:학술대회논문집
• /
• 한국복합재료학회 2000년도 추계학술발표대회 논문집
• /
• pp.12-16
• /
• 2000

This study is about the effect of braiding on the 2-D biaxial braided hollow composite(BD) compared with unidirectional hollow composite(UD). The specimens were made of T700S Carbon/Epoxy prepreg and T700S dried Carbon yarns. Fiber volume fraction of UD and BD was obtained experimentally and analytically. Fiber volume fraction of BD was derived based on unit cell of braiding yarn section. Bending test was executed to investigate the effect of braiding part. The result of experiment and analysis of fiber volume fraction has good agreement. Bending strength of BD is about 20% higher than that of UD.

• 한국염색가공학회지
• /
• 제21권4호
• /
• pp.11-22
• /
• 2009

This study surveys the optimum processing conditions of ATY for PET braiding for automotive hoses. For this purpose, high tenacity and low shrinkable PET filaments with three types of deniers are prepared. Twenty seven ATY specimens are manufactured with variation of feed speed and overfeed on the air jet texturing machine. The physical properties of various yam according to the ATY processing conditions are measured and analysed for deciding the optimum ATY processing condition. Two kinds of ATY filaments made under the optimum air texturing conditions are processed with variation of tpm, heat setting temperature and heat setting time on the 2-for-l twister and setting chamber, respectively. The optimum twisting and heat setting conditions are decided through analysis of the yam physical properties. Finally, the braiding fabric specimens are manufactured using conventional filament and newly developed filament made under optimum twisting and heat setting conditions. The bursting strengths of these braiding specimens are compared and discussed between two types of specimens.

• 한국공작기계학회논문집
• /
• 제12권4호
• /
• pp.70-76
• /
• 2003

Braiding machines of maypole type have complex guide tracks. It is not easy to speed up drivers while carriers are moving at high speed. This paper presents a new design approach using dynamic analysis and modeling for moving carriers on the guide tracks. The proposed approach will be shown to be effective by using simulation tool, WORKING MODEL $2D^{\circledR}$, for high speed drivers on new models of braiding machines of maypole type.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2002년도 추계학술대회 논문집
• /
• pp.875-878
• /
• 2002

Braiding machines of maypole type have complex guide tracks. It is not easy to speed up drivers while carriers are moving with being at high speed. This paper presents a new design approach using dynamic analysis for moving carriers on the guide tracks. The proposed approach will be shown to be effective by using the simulation tool, WORKING MODEL 2D(equation omitted), for the high speed drivers on new models of braiding machines of maypole type.

• 대한수학회논문집
• /
• 제21권2호
• /
• pp.337-345
• /
• 2006

John Harer conjectured that the canonical map from braid group to mapping class group induces zero homology homomorphism. To prove the conjecture it suffices to show that this map preserves the first Araki-Kudo-Dyer-Lashof operation. To get information on this homology operation we need to investigate the image of braiding under the Harer map. The main result of this paper is to give both algebraic and geometric interpretations of the image of braiding under the Harer map. For this we need to calculate long chains of consecutive actions of Dehn twists on the fundamental group of surface.

• 한국염색가공학회지
• /
• 제28권4호
• /
• pp.246-252
• /
• 2016

In comparison to metal alloys, braided composite features a high impact resistance and crash energy absorption potential, and also it still remained competitive stiffness and strength properties. Braiding angle is one of the most important parameters which affect the mechanical behaviors of braided composite. This paper presents transverse low velocity impact failure behavior analysis on the carbon 3D triaxial braided composite tube with the braiding angle of $20^{\circ}$, $50^{\circ}$ and $80^{\circ}$. The flexural behaviour of 3D triaxial braided composite tube under bending loads was studied by conducting quasistatic three point bending test. Also, the low velocity impact responses of the braided composite tubes were also tested to obtain load-displacement curves and energy absorption. Consequently, the increase of the braided angle, the peak load also increases owing to the bigger bending stiffness.

• Composites Research
• /
• 제31권6호
• /
• pp.392-397
• /
• 2018

본 연구에서는 기존의 스틸재 타이로드를 브레이딩 공법을 적용한 탄소복합재로 개발하고자 하였다. 탄소복합재 타이로드는 기존 제품과 동등한 성능을 만족시키기 위하여 브레이딩 직조에 필요한 코어 단면설계, 코어와 탄소섬유의 접합부에 대한 구조형상설계를 진행하였다. 그리고 브레이딩 공법을 적용한 시편을 제작하여 시험평가를 통해 구조해석에 적용하였다. 제작 공정은 브레이딩 직조 후 인퓨전 공정을 거쳐 후경화 공정까지 진행하였으며 최종 제품에 대한 시험평가는 인장 시험, 비틀림 시험, 압축 시험과 피로시험을 순차적으로 진행하여 모두 만족시켰다. 또한 탄소복합재 타이로드의 중량을 기존 제품 대비 약 37% 정도 경량화시킬 수 있었다.

• 한국복합재료학회:학술대회논문집
• /
• 한국복합재료학회 2002년도 추계학술발표대회 논문집
• /
• pp.131-134
• /
• 2002

Braided carbon fiber reinforced Al matrix composites were developed and characterized. Braided carbon fiber preforms with braiding angles of $30^{\circ}$, $45^{\circ}$ and $60^{\circ}$ were manufactured by using a braiding machine. The manufactured braided carbon fibers were used as reinforcement to fabricate Al matrix composites by employing a pressure infiltration casting method. In the processing of pressure infiltration casting, important processing parameters such as melting temperature, preheating temperature of preform and applied pressure were optimized. Prediction of elastic constants on composites was performed by using the volume averaging method, which utilizes the coordinate transformation and the averaging of stiffeness and compliance constants based upon the volume of each reinforcement and matrix material. The elastic moduli of composites were evaluated by using Resonant Ultrasound Spectroscopy(RUS) method and compared with the elastic moduli obtained from static tensile test method.

• Korea-Australia Rheology Journal
• /
• 제19권1호
• /
• pp.17-25
• /
• 2007

In liquid composite molding (LCM), composites are produced by impregnation of a dry preform with liquid resin. The resin flow through the preform is usually described by Darcy's law and the permeability tensor must be obtained for filling analysis. While the resin flow in the thickness direction can be neglected for thin parts, the resin flow in the transverse direction is important for thicker parts. However, the transverse permeability of the preform has not been investigated frequently. In this study, the transverse permeability was measured experimentally for five different fiber preforms. In order to verify the experimental results, the measured transverse permeability was compared with numerical results. Five different fiber mats were used in this study: glass fiber woven fabric, aramid fiber woven fabric, glass fiber random mat, glass fiber braided preform, and glass/aramid hybrid braided preform. The anisotropic braided preforms were manufactured by using a three dimensional braiding machine. The pressure was measured at the inlet and outlet positions with pressure transducers.

• Composites Research
• /
• 제16권2호
• /
• pp.33-40
• /
• 2003

본 논문은 열경화성수지 적층 복합재료의 낮은 충격 특성과 층간 분리 현상을 개선하고자 열가소성 수지 및 3차원 직조 프리폼을 사용한 복합재료 제조와 물성 특성화에 대한 것이다. 새로운 기술인 co-braiding 성형법으로 열가소성 PEEK 섬유와 탄소섬유를 혼합한 섬유를 제조하였으며. 층간 분리 억제 특성을 현저하게 향상시키기 위하여 두께방향의 섬유를 가지는 3차원 직조형 프리폼을 제조하였다. 혼합섬유로 제조된 프리폼에 열성형 공정을 적용함으로써 열가소성 복합재료를 제조하였으며. 혼합섬유의 PEEK 섬유는 용융온도에서 용융되어 탄소섬유 사이로 함침이 완벽하게 일어남을 확인하였다. 또한, APC-2/AS4 프리프레그를 사용한 준 등방 적층 복합재료를 제조하여 3차원 직조형 열가소성 복합재료의 특성과 비교하였다. 항공기 소재로서의 적용 가능성을 알아보기 위하여 open hole 인장시험, 충격시험, 및 충격 후 압축시험 등의 결과를 통하여 3차원 직조형 열가소성 복합재료는 기존의 적층 복합재료보다 우수한 내 충격성 손상허용치를 가짐을 보였다.