• 한국산학기술학회논문지
• /
• 제12권6호
• /
• pp.2707-2712
• /
• 2011

본 논문에서는 400V, 120W 급 LED 구동을 위한 1단 전류 경계모드(Boundary Condition Mode) 제어방식의 역률 개선 제어회로를 설계하였다. 제안하는 제어회로는 역률 개선 및 고조파 발생을 감소시키는 기능을 가지고 있으며, 또한 PFC(Power Factor Correction)회로 내에서 상대적으로 많은 면적을 차지하는 기존의 바이폴라 트랜지스터 구조 대신 새로운 CMOS 회로로 설계하였다. 기존대비, 약 30% 정도의 레이아웃 면적을 줄이게 되었고, 상용화 시 칩의 가격 경쟁력이 클 것으로 사료된다.

• 한국항공우주학회지
• /
• 제33권8호
• /
• pp.42-49
• /
• 2005

아음속풍동 폐쇄형 시험부의 벽면효과 보정을 위한 새로운 blockage 보정 기법을 개발하였다. 개발된 보정 기법은 실속항력계수와 separation blockage의 비선형 관계를 이용하여 선형 양력곡선 기울기 영역에서 후실속 영역까지 실시간으로 보정이 가능하게 하였다. 본 연구에서 제시한 방법은 bluff body 시험 결과를 사용하는 고전적 방법과 벽면압력측정 방법과 비교하여 그 타당성을 검증하였다. 그 결과 본 연구에서 제시한 보정 방법은 실속 및 후실속 영역에서 bluff body 방법보다 우수한 보정 결과를 보이며 벽면압력측정 방법과 같은 정확도로 보정됨을 확인할 수 있었다.

• 한국생산제조학회지
• /
• 제7권5호
• /
• pp.72-84
• /
• 1998

In order ot study the influence of a circular inclusion on a stress field near a crack tip, mutual interference of a slant crack and the circular inclusion is analyzed of a bimaterial inclusion. As the crack emanates at the equivalent slant crack angle the correction factors FⅠ and FⅡ for the inclusion wit small Young's modulus were found to decrease as the inclusion radius increased. The correction factors for inclusion with large Young's modulus increase as the inclusion radius increases at the equivalent radius of the inclusion, the correction factors decrease as the slant crack angle increases for the aspect ratio $\frac{c}{W}$ = 0.1 irrespective of the Young's modulus. For $\frac{c}{W}$ greater than 0.2, they increase as the slant crack angle increases. There is no influence of stress mutual interfce after crack emanates beyond the inclusion radius.

• Journal of Power Electronics
• /
• 제12권5호
• /
• pp.708-714
• /
• 2012

This paper presents a new interleaved pulse-width modulation (PWM) boost-flyback converter to achieve power factor correction (PFC) and regulate DC bus voltage. The adopted boost-flyback converter has a high voltage conversion ratio to overcome the limit of conventional boost or buck-boost converter with narrow turn-off period. The proposed converter has wide turn-off period compared with a conventional boost converter. Thus, the higher output voltage can be achieved in the proposed converter. The interleaved PWM can further reduce the input and output ripple currents such that the sizes of inductor and capacitor are reduced. Since boundary conduction mode (BCM) is adopted to achieve power factor correction, power switches are turned on at zero current switching (ZCS) and switching losses are reduced. The circuit configuration, principle operation, system analysis, and design consideration of the proposed converter are presented in detail. Finally, experiments conducted on a laboratory prototype rated at 500W were presented to verify the effectiveness of the converter.

• 한국해양공학회지
• /
• 제27권1호
• /
• pp.80-84
• /
• 2013

This study is to develop the simplified formulae for added mass coefficient of a 2-D floating body with a semi-circle section in a finite water depth. The semi-circle floating body may represent a simplified midship section transformed by Lewis form, which can be used for the ship motion analysis by strip theory. Since the added mass coefficient varies with motion frequencies and sea bottom effect, the correction factor representing the effect of water depth and frequencies is developed for accurate prediction of added mass. Using a two-dimensional numerical wave tank (NWT) technique based on the boundary element method (BEM) including sea bottom boundary the reference values of added mass are calculated to develop the correction factor. For verification and effectiveness of the formulae, the predicted added mass coefficients for various frequencies and water depth ratios are compared with the calculated values from NWT technique.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2002년도 학술대회지
• /
• pp.553-556
• /
• 2002

A numerical study on the use of the momentum interpolation mettled for flows with a large body force is presented. The inherent problems of the momentum interpolation method are discussed first. Numerical experiments are performed for a typical flow involving a large body force. The tact that the momentum interpolation method may result in physically unrealistic solutions is demonstrated. Numerical experiments changing the numerical grid have shown that a simple way of removing the physically unrealistic solution is a proper grid refinement where there is a large pressure gradient. An effective way of specifying the pressure and pressure correction at the boundary by a local mass conservation near the boundary is proposed, and it is shown that this method can effectively remove the inherent problem of the specification of pressure and pressure correction at the boundary when one uses the momentum interpolation method.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2002년도 학술대회지
• /
• pp.815-818
• /
• 2002

The elliptic relaxation model(ERM) with the inhomogeneous correction intermediate between near wall with and far from the wall. The source of the ERM usually was appled quasi-homogeneous pressure-strain correlation in homogeneous situations. This formulation was easily applied to the linear model or non-linear pressure-strain model. It is observed that the boundary conditions of the relaxation operator dominate the homogeneous pressure-strain model in the near wall region. While looking at high-Reynolds number flows, it was found necessary to modify the effect of the relaxation operator throughout the log region by accounting for gradients of the flatness variable and turbulent length scales. These effects are kinematic blocking of the wall normal velocity fluctuation and pressure reflections from the surface. This model is wall distances and unit vectors which make the model applicable to flows boundary by a complex geometry. Inhomogeneous correction model is computed inertial and non-inertial channel flow These are compared DNS(Kim et at., Kristofffrsen & Andersson) for channel flow. The present model could be predicted well for rotating flows.

• Journal of applied mathematics & informatics
• /
• 제32권3_4호
• /
• pp.511-527
• /
• 2014

This paper provides a new application similar to the Local Defect Correction (LDC) technique to solve Poisson problem -u"(x) = f(x) with Dirichlet boundary conditions. The exact solution is supposed to have high activity in some region of the domain. LDC is combined with a fourth order compact scheme which is recently developed in Abbas (Num. Meth. Partial differential equations, 2013). Numerical tests illustrate the interest of this application.

• 한국방송∙미디어공학회:학술대회논문집
• /
• 한국방송공학회 1996년도 학술대회
• /
• pp.233-236
• /
• 1996

A new method of blocking effects reduction is proposed in this paper for use in low bitrate image coding. We use 28 DCT kernel functions of which boundary values are linearly independent, and Gram-Schmidt process is applied to the boundary values in order to obtain 28 boundary-orthonormal basis images. Then we use these basis images to obtain the correction terms for blocking artifacts reduction. A threshold of block discontinuity is introduced for improvement of visual quality by reducing image blurring. We also investigate the number of basis images needed for efficient blocking artifacts reduction when the compression ratio changes.

• Journal of the Korean Data and Information Science Society
• /
• 제9권1호
• /
• pp.77-88
• /
• 1998

Smoothing spline estimators are modified to remove boundary bias effects using the technique proposed in Eubank and Speckman (1991). An O(n) algorithm is developed for the computation of the resulting estimator as well as associated generalized cross-validation criteria, etc. The asymptotic properties of the estimator are studied for the case of a linear smoothing spline and the upper bound for the average mean squared error of the estimator given in Eubank and Speckman (1991) is shown to be asymptotically sharp in this case.