• Proceedings of the Korean Geotechical Society Conference
• /
• 2002.03a
• /
• pp.389-396
• /
• 2002

Engineers should be careful in the design of bonding piles into pile caps because they are weak points in the pile foundation. Therefore in this study, the mechanism of bonding piles into pile caps was explained, and the design method of the composite bonding method was proposed. And the proposed design method was verified in comparison with the result of the full scale test. Also, the characteristic for the bearing capacity and the mechanism of compressive load of bonding method were analyzed.

• Journal of the Korean Society of Hazard Mitigation
• /
• v.8 no.5
• /
• pp.7-13
• /
• 2008

This paper presents experimental and analysis studies about both the corroded steel expansion and the variation of poor bonding range between steel and concrete. A loss of overall bonding capacity at the concrete-steel interface is evaluated experimentally and crack patterns at the bottom of the concrete are presented here. Steel-concrete interface is covered by rubber due to present local loss of the concrete-steel interface bonding capacity. In case of crack analysis performed by commercial FEM programs. we investigated crack‘s pattern and location. Finally, it is concluded that overall flexural capacity of the reinforced concrete structure is increased by the corroded steel expansion and is dependent of the bonding range at the steel- concrete interface. These results give an important factor to decide a life of reinforced concrete structures.

• Asian Journal for Public Opinion Research
• /
• v.3 no.1
• /
• pp.1-21
• /
• 2015

A recent public opinion survey found that the anti-corporate sentiment of South Korean citizens is primarily due to the misbehavior of Korean corporations. South Korean citizens' skepticism of corporations may hinder the democratic and economic development of the country. As a driving force for community development, social capital is considered to enable citizens to collaborate with one another to resolve a shared problem. Specifically, this study pays attention to the relationship among social capital, corporate capacity, and trust, which may perhaps contribute to developing a democratic environment in Korean society. The study aims to explore whether Korean citizens' perceived corporate bonding and bridging social capital affect corporate capacity for collaborative action and trust in corporations. A Web survey of 385 South Koreans was conducted. The findings show that perceived bonding social capital among employees is positively related to corporate capacity for collaboration action. Moreover, perceived bonding among employees and bridging social capital between employees and local residents are positively related to corporate capacity for collaboration action and trust in corporations. These findings suggest that researchers and practitioners for organizational development and community-building need to enhance corporate social capital.

• Journal of the Korean Society for Advanced Composite Structures
• /
• v.6 no.4
• /
• pp.30-37
• /
• 2015

iFLASH System is new structural floor system which consists of sandwich panels filled with nano-composite. The nano-composite has low specific gravity and high bonding strength with steel plates. The bonding strength is one of important factors for structural performance of iFLASH System and it can further be improved by surface preparation such as blast metal cleaning. However, using none blast steel plates is recommended since surface preparation generates additional fabrication time and cost. In this study, a bonding strength test and bending experiment were conducted to check feasibility of applying none blast steel plates to iFLASH System. Moreover, stress in bonding plane between steel plates and nano-composite was analytically evaluated by finite element method. Consequently, flexural capacity of the specimen was 11% higher than theoretically calibrated value and its flexural behavior was structurally efficient without defect of bonding.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.23 no.1
• /
• pp.29-33
• /
• 2010

As the demands for the higher data transmission speed and capacity as well as integration density grow throughout the network, much works have being done in order to integrate the Electrical PCB with Optical PCB. However, one of the most troublesome problems in the commercial bonding process is to need the high temperature for the bonding. Due to the high temperature bonding process, lots of side problems are followed such as warpage and crack, etc. In this paper, we tried to develop the new bonding technology with low temperature around $100^{\circ}C$. As a result of this study, the PCB bonding technology with high bonding strength is demonstrated with the value of bonding strength from 7 to 8 MPa at the temperature of $100^{\circ}C$.

• Journal of the Korean Society of Safety
• /
• v.27 no.2
• /
• pp.78-83
• /
• 2012

This is a study to confirm how to improve and substitute the existing re-bar with other material such as a fiber rope, especially super fiber rope having much more strong tensile strength. 6(b) different fiber rope reinforced beam with a section of $20{\times}30cm$ have been made and tasted as variables designed in the study. The larger diameter of fiber rope, the more capacity of the beam, even though fiber reinforced beam are increased with ten(10)percent, each. Lower capacity of fiber-reinforced beam than normal RC beam has been analyzed theoretically and empirically, based on a lot of experiences of the same size beam test. Fiber rope-reinforced concrete beam does not have sufficient capacity than RC beam due to insufficient bonding capacity of fiber rope in concrete. It leads to decrease beam bearing capacity and crack around lower center of the beam. Therefore, bonding reinforcement of fiber rope beam such as pinning a triangles steel pin in each knot of fiber rope contributes to improving bearing capacity of fiber rope reinforcing beam.

• Transactions of Materials Processing
• /
• v.28 no.1
• /
• pp.15-20
• /
• 2019

The superplastic forming/diffusion bonding process has been developed to fabricate a core frame structure with joint nodes out of tubes, for the development of a titanium high performance bicycle. The hydroforming process has been applied for bulging of a tube in the superplastic condition before, and during the diffusion bonding process. In this experiment, a commercial Ti-3Al-2.5V tube was selected as raw material for the study. The forming experiment has been performed using a servo-hydraulic press with a capacity of 200 ton. Next, nitrogen gas was used to acquire necessary pressure for the bulging and bonding of the tubes to fabricate the joint nodes. The pertinent processing temperature was $870^{\circ}C$ for the superplastic hydroforming/diffusion bonding (SHF/DB) process, using the Ti-3Al-2.5V tube. The bonding quality and the progress of bulging and diffusion bonding have been observed by the investigation of the joining interfaces at the cross section of the joint structure. The control of the nitrogen pressure throughout the SHF/DB process, was an important factor to avoid any significant defects in the joint structure. The whole progress stage of the diffusion bonding could be observed at a joint interface. A core structure with 5 joint nodes to manufacture a titanium bicycle could be obtained in a SHF/DB process.

• Steel and Composite Structures
• /
• v.19 no.3
• /
• pp.735-757
• /
• 2015

Composite bonding steel plate (CBSP) is a newly developed type of structure strengthened technique applicable to the existing RC beam. This composite structure is applicable to strengthening the existing beam bearing high load. The strengthened beam consists of two layers of epoxy bonding prestressed steel plates and the RC beam sandwiched in between. The bonding enclosed and prestressed U-shaped steel jackets are applied at the beam sides. This technique is adopted in case of structures with high longitudinal reinforcing bar ratio and impracticable unloading. The prestress can be generated on the strengthening steel plates and jackets by using the CBSP technique before loading. The test results of full-scale CBSP strengthened beams show that the strength and stiffness are enhanced without reduction of their ductility. It is demonstrated that the strain hysteresis effect can be effectively overcome after prestressing on the steel plates by using such technique. The applied plates and jackets can jointly behave together with the existing beam under the action of epoxy bonding and the mechanical anchorage of the steel jackets. The simplified formulas are proposed to calculate the prestress and the ultimate capacities of strengthened beams. The accuracy of formulas was verified with the experimental results.

• Progress in Superconductivity and Cryogenics
• /
• v.1 no.2
• /
• pp.1-7
• /
• 1999

we evaluated the effects of joining process such as contact method. shape of joined area and pressure on the electrical and mechanical properties of Bi-2223 superconducting tape, Specifically. the current capacity of the jointed tape was measured as a function of uniaxial pressure. and the thermal shock, bonding strength and the thermal of the tape were evaluated and correlated to the microstructural evolution. It was observed that the current capacity was significanrly dependent on the uniaxial pressure The jointed tape, fabricated with a pressure of 1,000-1,600 Mpa. showed the highest value of current capacity results from improvements in core density, contacting area and grain alignment, ect. In addition, the strength of jointed tape was measured to be 86 Mpa, which is about 88% of the unjoined ape's strength. The irreversible strain($\varepsilon$irrev) for the jointed tape was measured to be 0.1%, smaller than that of unjoined tape ($\varepsilon$irrev= 0.3%). The decrease in the strength and irreversible strain for jointed tape is believed to be due to the irregular geometry/morphology of the transition area of the tape.

• Journal of the Korean Society of Industry Convergence
• /
• v.9 no.3
• /
• pp.183-190
• /
• 2006

Generally, application of steel pile as deep foundation member needs specials requirement for the connection method between steel pipe and concrete footing. To investigate real compressive behavior of connection member between steel pipe pile and concrete footing, three specimens were tested with carefully designed experimental system. Main test variable is the connection method between steel pipe pile and concrete footing. The bolted bonding method and hook bonding method was considered as the connection method in this study. From the test results gained from experiment, it was conformed that two types of connection method have the almost same compressive resistance capacity. Therefore, we can conclude that these two connection methods can be used as the strengthening method to verify the compressive composite action of concrete and steel pipe pile.