• Journal of Advanced Navigation Technology
• /
• v.19 no.1
• /
• pp.60-65
• /
• 2015

In the present study, compact $0^{th}$ order resonant antenna for 2.4 GHz ISM frequency band is newly proposed. In case of wireless communication systems such as wi-fi, bluetooth and Zigbee, antennas with omni-directional radiation pattern are necessary because of the demands for uniformly received electric field strength without variation for direction. It is well-known that $0^{th}$ order resonant antennas are not only advantageous for miniaturization but also have advantage of maintaining omni-directional radiation pattern. The proposed antenna is composed of two-element array in which the size of unit element should be smaller than ${\lambda}/4$ correspondent to the resonant length of typical monopole antennas The proposed antenna which is placed at middle and upper side of PCB with $50{\times}50mm^2$ size is designed and fabricated within limited space of $8{\times}5mm^2$. The measured impedance bandwidth ($S_{11}{\leq}-10dB$) is about 100 MHz (2.4~2.5 GHz) which corresponds to quite wide bandwidth in comparison with the antenna size, and also the measured peak gain over the passband is more than 3 dBi which is thought to be slightly wider than the other $0^{th}$ order resonant antenna.

• Journal of IKEEE
• /
• v.24 no.3
• /
• pp.838-844
• /
• 2020

In this paper, we propose an efficient Viterbi processor using Joint Viterbi detection and decoding (JVDD) algorithm for a for bluetooth low energy (BLE) system. Since the convolutional coded Gaussian minimum-shift keying (GMSK) signal is specified in the BLE 5.0 standard, two Viterbi processors are needed for detection and decoding. However, the proposed JVDD scheme uses only one Viterbi processor by modifying the branch metric with inter-symbol interference information from GMSK modulation; therefore, the hardware complexity can be significantly reduced without performance degradation. Low-latency and low-complexity hardware architecture for the proposed JVDD algorithm was proposed, which makes Viterbi decoding completed within one clock cycle. Viterbi Processor RTL synthesis results on a GF55nm process show that the gate count is 12K and the memory unit and the initial latency is reduced by 33% compared to the modified state exchange (MSE).

• Proceedings of the IEEK Conference
• /
• 2000.06e
• /
• pp.191-194
• /
• 2000

A 2.4 GHz single ended two stage low noise amplifier(LNA) is designed for Bluetooth application. The circuit was implemented in a standard digital 0.25 $\mu\textrm{m}$ CMOS process with one poly and five metal layers. At 2.4 GHz, the LNA dissipates 34.5 mW from a 2.5V power supply voltage and provides 24.6 dB power gain, 2.85 dB minimum noise figure, -66.3 dB reverse isolation, and an output 1-dB compression level of 8.5 dBm.

• The Journal of the Korea institute of electronic communication sciences
• /
• v.18 no.1
• /
• pp.177-184
• /
• 2023

In this paper, based on Arduino, a vehicle is installed at the bottom of the 3D printer so that Arduino controls the vehicle that can expand the moving space. A stepping motor was mounted on the front wheel of the vehicle and precisely controlled using a motor driver. As a result, when moving 5cm, 25cm, and 50cm, the mean value of error rate was 0.6%, 0.04%, and 0.02%, respectively, to enable accurate distance control.

• ETRI Journal
• /
• v.30 no.5
• /
• pp.729-734
• /
• 2008

Wireless communication systems, such as WLAN or Bluetooth receivers, employ preamble data to estimate the channel characteristics, introducing stringent settling-time constraints. This makes the use of traditional closed-loop feedback automatic gain control (AGC) circuits impractical for these applications. In this paper, a compact feedforward AGC circuit is proposed to obtain a fast-settling response. The AGC has been implemented in a 0.35 ${\mu}m$ standard CMOS technology. Supplied at 1.8 V, it operates with a power consumption of 1.6 mW at frequencies as high as 100 MHz, while its gain ranges from 0 dB to 21 dB in 3 dB steps through a digital word. The settling time of the circuit is below 0.25 ${\mu}s$.

• Proceedings of the KIEE Conference
• /
• 2011.07a
• /
• pp.1638-1639
• /
• 2011

본 논문에서는 초소형 무선 USB 동글 장치를 위한 광대역 접힌(folded) 모노폴 안테나를 제안하였다. 제안된 안테나는 CPW 급전으로부터 삼지창 형상의 선로를 적용하여 광대역 특성을 구현하였다. 최종 설계된 안테나의 크기는 $16{\times}44.8{\times}3.5\;mm^3$이며, low-profile의 무선 USB 동글용 안테나에 적합하다. 제안된 안테나는 $S_{11}$ < -10 dB 기준으로 2.28~10.8 GHz의 공진 주파수 대역을 가지므로 WiBro (2.3~2.4 GHz), Bluetooth (2.4~2.484 GHz), WiMAX (2.5~2.7 GHz, 3.4~3.6 GHz), satellite DMB (2.605~2.655 GHz), 802.11b/g/a WLAN (2.4~2.485 GHz, 5.15~5.825 GHz), UWB(3.1~10.6 GHz)의 무선 대역을 지원 할 수 있다. 측정된 평균 이득의 범위는 -3.41 dBi 에서 -0.84 dBi 이다.

• Design & Manufacturing
• /
• v.15 no.3
• /
• pp.45-49
• /
• 2021

In this study, during the injection molding process, a device was manufactured and evaluated that calculates a cooling time by measuring a vibration signal generated from a mold using an acceleration. The last two parts, one of which has a large magnitude change in the measured vibration signal of a mold, were divided into a cooling start section (paking end section) and a mold opening section, and the time difference at the relevant points was calculated as the cooling time. The cooling time was monitored on a 5-inch light guide plate mold by applying the method. The manufactured device was attached to a fixed base of mold to measure the cooling time, and data was obtained remotely using Bluetooth technology. Then, the measured cooling time was compared with the cooling time set in the injection molding machine to evaluate the accuracy. As a result of the experiment, the cooling times measured by the devices were 15.675±0.024 sec, 20.637±0.014 sec and 25.623±0.079 sec of each conditions. Also, the measurement results were shown with errors of 0.655±0.044 sec, 0.637±0.014 sec, and 0.662±0.013 sec, respectively.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.45 no.11
• /
• pp.89-94
• /
• 2008

In this paper, a cascade of a wideband amplifier and a high-Q bandpass filter (BPF) has been realized in a 0.18mm CMOS technology for the applications of subsampling direct-conversion receivers. The wideband amplifier is designed to obtain the -3dB bandwidth of 5.4GHz, and the high-Q BPF is designed to select a 2.4GHz RF signal for the Bluetooth specifications. The measured results demonstrate 18.8dB power gain at 2.34GHz with 31MHz bandwidth, corresponding to the quality factor of 75. Also, it shows the noise figure (NF) of 8.6dB, and the broadband input matching (S11) of less than -12dB within the bandwidth. The whole chip dissipates 64.8mW from a single 1.8V supply and occupies the area of $1.0{\times}1.0mm2$.

• Journal of Korea Society of Digital Industry and Information Management
• /
• v.17 no.3
• /
• pp.9-15
• /
• 2021

In this paper, the Embedded MEMS system to the power apparatus used Edge Impulse machine learning tools and therefore an improved predictive system design is implemented. The proposed MEMS embedded system is developed based on nRF52840 system and the sensor with 3-Axis Digital Magnetometer, I2C interface and magnetic measurable range ±120 uT, BM1422AGMV which incorporates magneto impedance elements to detect magnetic field and the ARM M4 32-bit processor controller circuit in a small package. The MEMS embedded platform is consisted with Edge Impulse Machine Learning and system driver implementation between hardware and software drivers using SensorQ which is special queue including user application temporary sensor data. In this paper by experimenting, TensorFlow machine learning training output is applied to the power apparatus for analyzing the status such as "Normal, Warning, Hazard" and predicting the performance at level of 99.6% accuracy and 0.01 loss.

• The Journal of the Korea institute of electronic communication sciences
• /
• v.14 no.5
• /
• pp.991-1000
• /
• 2019

The flying-disc game has started since 1940. It has been spreading rapidly in Korea since 2007, mainly in elementary schools. Additionally, as sports science has been developed, research on flying discs has been continued to build a monitoring system for technological improvement and efficiency. In this paper, we acquire information on the user's flying-disc using 9-axis motion sensor and GPS. Then we propose a method for wireless transmission using Bluetooth 5.0. Specifically, the HW platform was designed and implemented not only to monitor a real-time data but also to compare and analyze rotational speed, flight trajectory, and a count of disc rotation through post-processing.