• The Korean Journal of Nuclear Medicine
• /
• v.34 no.4
• /
• pp.336-343
• /
• 2000

Purpose: Thallous-201 chloride produced at Korea Cancer Center Hospital(KCCH) is used in detecting cardiovascular disease and cancer. Thallium impurity can cause emesis, catharsis and nausea, so the presence of thallium and other metal impurities should be determined. According to USP and KP, their amounts must be less than 2 ppm in thallium and 5 ppm in total. In this study, the detection method of trace amounts of metal impurities in $[^{201}Tl]$TICI injection with polarography was optimized without environmental contamination. Materials and Methods: For the detection of metal impurities, Osteryoung Square Wave Stripping Voltammetry method was used in Bio-Analytical System (BAS) 50W polarograph. The voltammetry was composed of Dropping Mercury Electrode (DME) as a working electrode, Ag/AgCl as a reference electrode and Pt wire as a counter electrode. Square wave stripping method, which makes use of formation and deformation of amalgam, was adopted to determine the metal impurities, and pH 7 phosphate buffer was used as supporting electrolyte. Results: Tl, Cu and Pb in thallous-201 chloride solution were detected by scanning from 300 mV to -800 mV Calibration curves were made by using $TINO_3,\;CuSO_4\;and\;Pb(NO_3){_2}$ as standard solutions. Tl was confirmed at -450 mV peak potential and Cu at -50 mV Less than 2 ppm of Tl and Cu was detected and Pb was not detected in KCCH-produced thallous-201 chloride injection. Conclusion: Detection limit of thallium and copper is approximately 50 ppb with this method. As a result of this experiment, thallium and other metal impurities in thallous-201 chloride injection, produced at Korea Cancer Center Hospital, are in the regulation of USP and KP Polarograph could be applied for the determination of metal impurities in the quality control of radiopharmaceuticals conveniently without environmental contamination.

• Journal of agriculture & life science
• /
• v.45 no.2
• /
• pp.125-133
• /
• 2011

This study was conducted on greenhouses whose side heights had been raised after the columns of 1-2W basic type greenhouses had been cut and welding with the same-sized pipes. When the wind load or snow load affects restructured pipe greenhouse like this, those parts will be structurally unsafe. To examine this, the bending strength of welded columns were measured through four stages and compared with the pipes in their original condition. Results are as follows. In the case of a bending test on welded joints about steel pipes used for greenhouses, satisfactory results couldn't be drawn because sections of both ends and the loading parts couldn't endure loads and sank regardless of loading methods. Partial problems could be solved by inserting inside pipe(steel bar) at the sections and the loading parts, but it was necessary to devise more satisfactory bending test methods. The strength of welded joints wasn't much different compared with original conditions and demonstrated only slight differences according to the sample production conditions. However, significant incompleteness in the welding process was expected to cause a decisive loss in strength. On the assumption that there were no problems in the welding process or with regard to the inclination of sub materials for columns after connection, it was deemed reasonable to assume that the strength of welded pipes was about 84~90% of the strength of the pipes in their original condition. Considering mid- and long-term strength decline following the onset of rust at joints or welding sections, structural changes in the main sub materials that are used for greenhouses at farmhouses have to be avoided to ensure structural safety, unless these changes are inevitable.

• Applied Chemistry for Engineering
• /
• v.30 no.5
• /
• pp.569-579
• /
• 2019

In this study, the effect anti-oxidant, anti-inflammatory, and liver protective activity was investigated via quick ultrasonic disintegration of pine pollen using a probe sonicator (PS) followed by the extraction with water, 70% ethanol, and 100% ethanol. The anti-inflammatory effect was studied by measuring the production of nitric oxide (NO) and cytokine in RAW264.7 cells induced with lipopolysaccharides (LPS). The cell toxicity was also checked with an 3-(4,5-dimethylthiazol-2-yl)-2,5-diphenyltetrazolium bromide (MTT) assay, and the experiment was conducted using non-toxic $100{\mu}g/mL$. The NO inhibition rate was highest in the 70% ethanol PS group at $85.99{\pm}0.12%$. Also an excellent efficiency was obtained from the results of interlukin-1 beta ($IL-1{\beta}$) and tumor necrosis factor alpha ($TNF-{\alpha}$), which is related to inflammation-related cytokine, with the respective inhibition rates of 63 and 22%. To examine liver protective activity, HepG2 cells were treated with Taclin, and the generation of glutamic oxaloacetic transaminase (GOT) and lactate dehydrogenase (LDH) was measured in the culture solution. From GOT and LDH generation results, the inhibition rates in the 70% ethanol PS group were 28% and 13%, respectively, which was higher compared to that of using negative control group. Our results suggest that pine pollen extracted in 70% ethanol using PS may be used to develop food products that have anti-aging, anti-inflammatory, and liver protective effects.

• Journal of Food Hygiene and Safety
• /
• v.36 no.5
• /
• pp.418-429
• /
• 2021

This paper investigates the antioxidant activity and quality characteristics of yanggaeng containing white ginseng and red ginseng extracts and their enzyme hydrolysates that were produced for the purpose of the study. White and red ginseng extracts were hydrolyzed using Rapidase C80 max, Pyr-flo, and Ultimase MFC. Ginsenoside F2 and compound K (CK) were not detected in white and red ginseng before enzymic reaction but were detected in white and red ginseng hydrolyzed through Rapidase C80 max, Pyr-flo, and Ultimase MFC, and the content of CK was the highest in the second enzymic reaction group of red ginseng. Upon preparing yanggaeng containing white and red ginseng before or after enzymatic hydrolysis, the polyphenol content and antioxidant abilities were analyzed. The yanggaeng containing enzyme-hydrolyzed white ginseng and red ginseng showed greater total polyphenol content, superior DPPH radical scavenging activity, superior ABTS radical scavenging activity, and superior FRAP analysis results compared to the yanggaeng that doesn't contain white or red ginseng. As the enzymic reaction was performed in the added white and red ginseng, the antioxidant activity increased significantly (P<0.05). In brightness(L^*), non-additive yanggaeng (control group) was the highest, red ginseng yanggaeng (RG) showed the highest redness(a^*), and the white ginseng yanggaeng (WG) showed the highest yellowness(b^*). In terms of texture, the yanggaeng containing red ginseng with second hydrolysis (RG-T2) showed significantly high results in hardness, springiness, chewiness, cohesiveness, and gumminess (P<0.05). In conclusion, treating white and red ginseng with Rapidase C80 max, Pyr-flo, and Ultimase MFC is very useful in ginsenoside deglycosylation and will produce CK with excellent biological activity. It can also be seen that yanggaeng containing white and red ginseng hydrolyzed with enzymes significantly increase total polyphenol and antioxidant activity compared to the control group (yanggaeng with no added ginseng). These results will be useful as excellent foundational data for the production of functional yanggaeng in the future.

• Journal of Life Science
• /
• v.28 no.11
• /
• pp.1339-1346
• /
• 2018

In Korea, edible mushrooms are produced largely on commercial artificial media, so the annual production of spent mushroom substrate (SMS), as a by-product of the mushroom industry, is estimated at over 200 million tons. This SMS is assumed to contain abundant fungal mycelia and pre-fruiting bodies, as well as various nutritive and bioactive compounds that are presently discarded. This study examined the physico-chemical, nutritional, and enzymatic characteristics of uninoculated sterilized medium (USM) and SMS of shiitake mushrooms with the aim of developing a high-value added product from SMS. The contents of crude protein, crude lipid, and ash were higher after the third SMS harvest ($SMS-A-3^{rd}$) than in USM or $SMS-A-1^{st}$. The contents of Ca, Mg, and P in $SMS-A-3^{rd}$ were 2.95, 2.35, and 2.1-fold higher compared than in USM. No As or Cd was detected in USM or SMS. The pH, Brix, and acidity were 4.6, 20.0, and 1.4, respectively in $SMS-A-3^{rd}$, but 5.6, 6.0, and 0.0, respectively, in USM. These results suggest a highly active production of soluble components and organic acids in $SMS-A-3^{rd}$. The distinct color differences noted for USM, $SMS-A-1^{st}$, and $SMS-A-3^{rd}$ could be used as a mycelial growth indicator. Enzyme activity assays using the APIZYM system showed that SMS is a potent source of hydrolysis-related enzymes, especially esterase (C4) and ${\beta}$-glucuronidase. Our results suggested that the SMS of shiitake has a high potential for use in environmental, agricultural, and stock-breeding industries, for example, as active ingredients for sewage treatment, waste-polymer degradation, and feed additives.

• Clean Technology
• /
• v.25 no.3
• /
• pp.223-230
• /
• 2019

This research was performed to evaluate the characteristics of food waste from 5 areas in Gangwon Province, Korea and to predict the $CH_4$ gas production rate. Food wastes were sampled in July and September, 2017. The amount of methane gas generation was evaluated through the biochemical methane potential (BMP) test and a calculation method using chemical composition. Average bulk density and pH of the food wastes were in the range of $0.758{\sim}0.850g\;cm^{-3}$ and 4.29 ~ 4.75, respectively. By physical composition, vegetables were the highest with 56.43 ~ 72.81% with fruits recording 5.31 ~ 8.95%, cereals 1.60 ~ 18.73%, fish and meat 4.47 ~ 12.11%, and filtrate 1.76 ~ 3.64%. The average water content was 69.30 ~ 75.87%, and VS and ash content were 22.50 ~ 27.98% and 1.63 ~ 2.48%, respectively. In addition, $BOD_5$, $COD_{Cr}$, and $COD_{Mn}$ were in the ranges of $17,690.3{\sim}33,154.9mg\;L^{-1}$, $106,212.3{\sim}128,695.5mg\;L^{-1}$, and $51,266.1{\sim}63,426.3mg\;L^{-1}$, respectively. The NaCl content ranged from 0.81 to 1.17%. The results of elemental analysis showed that the contents of C, H, O, N, and S were 44.87 ~ 48.1%, 7.12 ~ 7.57%, 40.13 ~ 43.78%, 3.22 ~ 4.14%, and 0.00 ~ 0.02%, respectively. In a comparison of the methane production yield per VS mass of food waste, there was no significant difference between the cumulative amount (${0.303{\sim}0.354m_{CH4}}^3\;{kg_{VS}}^{-1}$) by the BMP test and the theoretical amount (${0.294{\sim}0.352m_{CH4}}^3\;{kg_{VS}}^{-1}$) calculated by chemical composition.

• Korean Journal of Agricultural and Forest Meteorology
• /
• v.23 no.1
• /
• pp.15-33
• /
• 2021

In this study, the possibility of discriminating Fire blight (FB) infection tested using the hyperspectral imagery. The reflectance of healthy and infected leaves and branches was acquired with 5 nm of full width at high maximum (FWHM) and then it was standardized to 10 nm, 25 nm, 50 nm, and 80 nm of FWHM. The standardized samples were divided into training and test sets at ratios of 7:3, 5:5 and 3:7 to find the optimal bands of FWHM by the decision tree analysis. Classification accuracy was evaluated using overall accuracy (OA) and kappa coefficient (KC). The hyperspectral reflectance of infected leaves and branches was significantly lower than those of healthy green, red-edge (RE) and near infrared (NIR) regions. The bands selected for the first node were generally 750 and 800 nm; these were used to identify the infection of leaves and branches, respectively. The accuracy of the classifier was higher in the 7:3 ratio. Four bands with 50 nm of FWHM (450, 650, 750, and 950 nm) might be reasonable because the difference in the recalculated accuracy between 8 bands with 10 nm of FWHM (440, 580, 640, 660, 680, 710, 730, and 740 nm) and 4 bands was only 1.8% for OA and 4.1% for KC, respectively. Finally, adding two bands (550 nm and 800 nm with 25 nm of FWHM) in four bands with 50 nm of FWHM have been proposed to improve the usability of multispectral image sensors with performing various roles in agriculture as well as detecting FB with other combinations of spectral bands.

• Korean Chemical Engineering Research
• /
• v.60 no.1
• /
• pp.86-92
• /
• 2022

Recently, the bio-healthcare market is enlarging worldwide due to various reasons such as the COVID-19 pandemic. Among them, biometric measurement and analysis technology are expected to bring about future technological innovation and socio-economic ripple effect. Existing systems require a large-capacity battery to drive signal processing, wireless transmission part, and an operating system in the process. However, due to the limitation of the battery capacity, it causes a spatio-temporal limitation on the use of the device. This limitation can act as a cause for the disconnection of data required for the user's health care monitoring, so it is one of the major obstacles of the health care device. In this study, we report the concept of a standalone healthcare monitoring module, which is based on both triboelectric effects and electromagnetic effects, by converting biomechanical energy into suitable electric energy. The proposed system can be operated independently without an external power source. In particular, the wireless foot pressure measurement monitoring system, which is rationally designed triboelectric sensor (TES), can recognize the user's walking habits through foot pressure measurement. By applying the triboelectric effects to the contact-separation behavior that occurs during walking, an effective foot pressure sensor was made, the performance of the sensor was verified through an electrical output signal according to the pressure, and its dynamic behavior is measured through a signal processing circuit using a capacitor. In addition, the biomechanical energy dissipated during walking is harvested as electrical energy by using the electromagnetic induction effect to be used as a power source for wireless transmission and signal processing. Therefore, the proposed system has a great potential to reduce the inconvenience of charging caused by limited battery capacity and to overcome the problem of data disconnection.

• Journal of Life Science
• /
• v.32 no.10
• /
• pp.784-791
• /
• 2022

This study observed changes in the body composition of Protaetia brevitarsis sinulensis larvae when reared with feed that included noni and nipa palm. Compared to the control group, the death rate and product yield of the treatment group were improved after the larval fasting process. The brightness of the larval powder of the treatment group increased, but the redness decreased. The crude fat content of the treated group was slightly increased according to the assays of the general components, but the mineral content was significantly increased. The total structural amino acids of the treatment group decreased, but the total free amino acids increased. The structural amino acids generally tended to decrease in the treatment group. However, the free amino acids showed no specific differences. Among the free amino acids, tryptophan, phosphoserine, and methylhistidine were highly increased in the treatment group, whereas threonine, methionine, and asparagine showed the opposite results. Among the polyunsaturated fatty acids, eicosapentaenoic acid (C20:5n3) of omega-3 was increased in the treatment group, but the omega-6 series was decreased. Since minerals, total free amino acids, and omega-3 fatty acids in the treatment group were increased compared to the control group, we suggest that noni and nipa palm can potentially be applied to the production of functionally improved substances as additional sources of feed for Protaetia brevitarsis sinulensis larvae.

• Ecology and Resilient Infrastructure
• /
• v.9 no.1
• /
• pp.68-76
• /
• 2022

In this study, the Habitat Suitability Index (HSI) was calculated in the Miho stream of the Geum river system, and the environmental ecological flow by point was evaluated. Two points (St.3 and St.8) representing the up and downstream of Miho Stream were selected, in order to calculate the Habitat Suitability Index, the depth and velocity at point where each species is appeared were investigated. The Habitat Suitability Index (HSI) was calculated by the Washington Department of Fish and Wildlife (WDFW) method using the number collected by water depth and velocity section and the results of the flow rate survey. Two target species were selected in this study; dominant species and swimming species sensitive to flow. In the case of a single species of Zacco platypus, the water depth was 0.1 - 0.5 m and the velocity was 0.2 - 0.5 m/s. For species of swimming fish, the water depth was 0.2 - 0.5 m and the velocity was 0.2 - 0.5 m/s. The discharge-Weighted Useable Area (WUA) relationship curve and habitat suitability distribution were simulated at the Miho Stream points St.3 and St.8. At the upstream St.3 of Miho Stream, the optimal discharge was simulated as 4.0 m³/s for swimming fishes and 2.7 m³/s for Zacco platypus. At the downstream point of St.8, species of swimming fish were simulated as 8.8 m³/s and Zacco platypus was simulated as 7.6 m³/s. In both points, the optimal discharge of swimming fish was over estimated. This is a result that the Habitat Suitability Index for swimming fish requires a faster flow rate than the habitat conditions of the Zacco platypus. In the calculation of the minimum discharge, the discharge of Zacco platypus is smaller and is evaluated to provide more Weighted Useable Area. In the case of swimming fishes, narrow range of depth and velocity increases the required discharge and relatively decreases the Weighted Useable Area. Therefore, when calculating the Habitat Suitability Index for swimming fishes, it is more advantageous to calculate the index including the habitat of all fish species than to narrow the range.