• 한국정보디스플레이학회:학술대회논문집
• /
• 2005.07b
• /
• pp.1211-1214
• /
• 2005

One of the important problems in recent AC-PDP technology is high efficiency. In this research, we have been investigated electro-optical characteristics of MgO protective layer after radio frequency(RF) plasma treatment using Ar, $O_2$, and $H_2$ gases. The breakdown voltage order was $O_2$ > Ar > Nontreatment > $H_2$. Also, brightness order was $O_2$ > Ar > Non-treatment > $H_2$. In this experiment, the best result was obtained after $O_2-plasma$ treatment.

• Journal of Electrochemical Science and Technology
• /
• v.13 no.2
• /
• pp.261-268
• /
• 2022

In this study, electrochemical treatment of urban wastewater with electrical conductivity of 1000 μS cm^-1 and chemical oxygen demand of 250 mg L^-1 was investigated using the variables of initial pH value, current density and flow rate. Electrocoagulation was used, in which aluminum and stainless steel were selected, as the electrochemical treatment process. The electrocoagulation process was operated in continuous mode. The data obtained in experimental studies show that the best COD removal efficiency occurred in experiments where the initial pH value was 6. The increase in current density from 5 A to 15 A decreased the removal efficiency from 79 to 67%. The increase in flow rate under constant current density also reduced the efficiency of removal as expected. In experiments in which current density and flow rate were examined together, the increase in flow rate allowed the application of higher current densities. This situation led to considerable reductions in energy consumption values, even if the COD removal efficiency did not significantly increase. The high COD removal obtained with the use of high flow rate and high current density indicates that the electrocoagulation process can be used for high flow rate municipal wastewater treatment.

• Current Photovoltaic Research
• /
• v.7 no.4
• /
• pp.103-110
• /
• 2019

Cu(In,Ga)₃Se₅ (β-CIGS) has a band gap of 1.35 eV, which is an optimum value for high solar-energy conversion efficiency. The effects of Cu and Ga content on the cell performance were investigated previously. However, the effect of Se content on the cell performance is not well understood yet. In this work, β-CIGS films were fabricated by three-stage co-evaporation of elemental sources with various Se fluxes at the third stage instead of at all stages. The average composition of five samples was Cu_1.05(In_0.59,Ga_0.41)3Se_y, where the stoichiometric y value is 5.03 and the stoichiometric Se/metal (Se/M) ratio is 1.24. We varied the Se/metal ratio in a range from 1.18 to 1.28. We found that the best efficiency was achieved when the Se/M ratio was 1.24, which is exactly the stoichiometric value where the CIGS grains on the CIGS surface were tightly connected and faceted. With the optimum Se/M ratio, we were able to enhance the cell efficiency of a β-CIGS solar cell from 9.6% to 12.0% by employing a Na₂S post deposition treatment. Our results indicate that Na₂S post deposition treatment is very effective to enhance the cell efficiency to a level on par with that in α-CIGS cell.

• Asian Pacific Journal of Cancer Prevention
• /
• v.15 no.1
• /
• pp.3-10
• /
• 2014

The Japan National Committee for the Union for International Cancer Control (UICC) and UICC-Asia Regional Office (ARO) organized an international session as part of the official program of the 72nd Annual Meeting of the Japanese Cancer Association to discuss the topic "What is cost-effectiveness in cancer treatment?" Healthcare economics are an international concern and a key issue for the UICC. The presenters and participants discussed the question of how limited medical resources can be best used to support life, which is a question that applies to both developing and industrialized countries, given that cancer treatment is putting medical systems under increasing strain. The emergence of advanced yet hugely expensive drugs has prompted discussion on methodologies for Health Technology Assessment (HTA) that seek to quantify cost and effect. The session benefited from the participation of various stakeholders, including representatives of industry, government and academia and three speakers from the Republic of Korea, an Asian country where discussion on HTA methodologies is already advanced. In addition, the session was joined by a representative of National Institute for Health and Care Excellence (NICE) of the United Kingdom, which has pioneered the concept of cost-effectiveness in a medical context. The aim of the session was to advance and deepen understanding of the issue of cost-effectiveness as viewed from medical care systems in different regions.

• Food Science of Animal Resources
• /
• v.36 no.1
• /
• pp.8-13
• /
• 2016

This study investigated the effect of soy protein hydrolysates (SPH) prepared by varying subcritical media on the physicochemical properties of pork patties. For resource of SPH, two different soybean species (Glycine max Merr.) of Daewonkong (DWK) and Saedanbaek (SDB) were selected. SPH was prepared by subcritical processing at 190℃ and 25 MPa under three different of media (water, 20% ethanol and 50% ethanol). Solubility and free amino group content revealed that water was better to yield larger amount of SPH than ethanol/water mixtures, regardless of species. Molecular weight (Mw) distribution of SPH was also similar between two species, while slightly different Mw distribution was obtained by subcritical media. For pork patty application, 50% ethanol treatment showed clear red color comparing to control after 14 d of storage. In addition, ethanol treatment had better oxidative stability than control and water treatment based on thiobarbituric acid-reactive substances (TBARS) analysis. For eating quality, although 20% ethanol treatment in SDB showed slightly higher cooking loss than control, generally addition of SPH did not affect the water-binding properties and hardness of pork patties. Consequently, the present study indicated that 50% ethanol was the best subcritical media to produce SPH possessing antioxidant activity, and the SPH produced from DWK exhibited better antioxidant activity than that produced SDB.

• International Journal of Advanced Culture Technology
• /
• v.6 no.2
• /
• pp.129-136
• /
• 2018

Our present study, we impregnated Al-Fe-Mg-Si (NFM) nanocomposites having various concentrations 0, 1000, 3000, and 5000 mg/L in biomass in order to make carbonized biomass. We characterized the properties of the impregnated samples through thermogravimetric/differential thermal analysis (TG-DTA), pore distribution, scanning electron microscopy (SEM). The best results were observed for a NFM nanocomposites concentration of 5000 mg/L. After the first heat treatment, carbonization, and activation processes, the fixed carbon ratio and iodine adsorptivity were increased by 21.89% and 368 mg/g, 23.98% and 475 mg/g, 26.40% and 238 mg/g, respectively. The remove rate of malodorous and VOCs were that the sample shows good removal capabilities. From above results, our sample could be used for the removal of noxious and malodorous gases and for the purification of wastewater.

• Environmental Engineering Research
• /
• v.17 no.3
• /
• pp.151-156
• /
• 2012

This research described the magnetic method for the rapid removal of green algae in water. We modified the pH, cation concentration, and magnetic powder concentration to discover the best removal performance. In order to rapidly remove green algae from water, we added magnetic powder and chitosan into algae water to make a magnetic substance and this was extracted by a strong neodymium magnet. The optimized conditions were pH of 6.5-7.5, chitosan concentration of 10 mg/L, and magnetite powder concentration of less than 0.05%. A higher removing rate was observed when a higher amount of magnetite or chitosan was used, but the total amounts of phosphorus or nitrogen were not decreased.

• Environmental Engineering Research
• /
• v.24 no.3
• /
• pp.418-426
• /
• 2019

Current available commercial membranes are not robust and are therefore destroyed if left to dry out or handled roughly. Woven fibre microfiltration (WFMF) membranes have advantages over its competitors with respect to durability, thus, favourable for the developing economies and operation during rough conditions. Evaluation of the effects of aeration and brushing as a flux enhancement strategies for WFMF membrane was the purpose of this study. The WFMF membrane was found to be susceptible to pore plugging by colloidal material and adsorption/attachment by microbiological contaminants. This led to a 50% loss in flux. Aeration as a single flux enhancement strategy proved insufficient to maintain high flux successfully. Therefore combined flux enhancement strategies yielded the best results.

• Environmental Engineering Research
• /
• v.24 no.2
• /
• pp.263-270
• /
• 2019

Palm oil mill effluent (POME) is the largest pollutant discharged into the rivers of Malaysia. Thus UF membrane study was conducted to investigate the effect of pressure and stirring speed on performance of POME treatment and fouling of membrane. Two types of membrane polyethersulfone (PES) and regenerated cellulose (RC) with molecular weight cut-off (MWCO) 5 and 10 kDa were used in this study. Results showed that, as pressure increased, fouling increased however permeate quality improved, the best pressure was 1.0 bar, where the fouling was not too high and produce good permeate quality. As stirring speed increased, fouling reduced and permeate quality improved, however, when stirring speed increased from 600 rpm to 800 rpm, there was no significant improvement on the permeate quality. Therefore, the best condition was at 1.0 bar and 600 rpm. PES membrane with MWCO 5 kDa showed the best permeate quality, even fouling slightly higher than RC membrane. The permeate quality obtained were analyzed in term of dissolved solid, turbidity, suspended solid, biological oxygen demand ($BOD_5$) and chemical oxygen demand (COD) were 538 mg/L, 1.02 NTU, < 25 mg/L, 27.7 mg/L and 62.8 mg/L, respectively with dominant type of fouling is cake resistance. Thus, it can be concluded water reuse standard was successfully achieved in terms of $BOD_5$ and suspended solid.

• Journal of the Korean Wood Science and Technology
• /
• v.31 no.4
• /
• pp.24-30
• /
• 2003

In order to develop structural 'bamboo zephyr board', properties of boards produced by various methods making zephyr were estimated. All of boards were tested with KS(Korean Standards) F 3014 Particle board, and results were summarized as follow. The zephyr boards produced by final 1.5 mm roller space had the best properties(MOR, MOE and IB strength) among boards produced by different final roller space. Also, they had the best properties(MOR and MOE) in bending test after 1 hour soaking treatment after 2 hour-boiling in water, which were similar to properties of boards in dry-condition. Thickness swelling(TS) of all boards was less than 12% required to the Korean Standards A 3014. Zephyr boards produced by final 1.5 mm roller space also had the lowest values among all of boards. Boards produced by non-treatment (in green condition) had the better strength than those of boards produced by different pre-treatment methods(boiling in water and in 0.3% NaOH) in bending test.