• Textile Coloration and Finishing
• /
• v.10 no.4
• /
• pp.37-44
• /
• 1998

The purpose of this study was to elucidate the effect of weight loss of polyethylene terephthalate(PET) fabrics on the mechanical properties such as bending and shear. In order to compare the effect of treatment machine on the mechanical properies of treated PET fabrics, PET fabrics were hydrolyzed with NaOH aqueous solution using Tank machine and Liquor flow machine, respectively. The results were as follows ： 1. The bending rigidity and shear stiffness of hydrolyzed PET fabric decreased markedly up to about 10％ weight loss regardless of treatment machines. At the above 10％ weight loss, the variation of these properties is nearly unchanged. In addition, the bending hysteresis and shear hysteresis also showed similar trend. 2. Weft density change of PET fabrics treated with Liquor flow machine decreased by 1pick/inch. It is assumed that this is attributed to the tension during the treatment of Liquor flow machine. On the other hand, the weft density change of PET fabrics treated with Tank machine is scarcely influeneced by the weight loss. While warp density of PET fabrics treated with Liquor flow machine had no change with weight loss, warp density of PET fabrics treated with Tank machine decreased by 6pick/inch due to the tension. 3. The bending rigidity and shear stiffness of PET fabrics hydrolyzed with liquor flow machine slightly higher than with Tank m/c at the above 10％ weight loss. It is assumed that this is caused by the increasement of the crossing pressure of warp and weft yarn and contact points of filaments in the yarns. Also, the bending and shear hysteresis of PET fabrics treated with Tank machine were higher than that of liquor flow machine.

• Journal of the Korea institute for structural maintenance and inspection
• /
• v.16 no.5
• /
• pp.68-77
• /
• 2012

The joint of existing steel grid composite deck is composed of lap splice of reinforcing bar with end hooks and field-placed concrete. In this study, bending tests of deck joint composed of concrete shear key and high tension bolts are carried out for the design variable, concrete shear key strengthened with steel plate or not, and test results are compared with flexural performance of the existing deck joint. Test results showed that the mechanical deck joint has about 30% ~ 60% more ultimate bending strength than the existing joint. According to analysis results of moment-curvature relationship, the initial bending stiffness of the existing deck joint is some higher than that of mechanical joint. But, after crack failure the structural performance of the existing deck joint is rapidly reduced. Furthermore, the deck joint with the strengthened shear key with steel plate has more bending moment capacity than the deck joint without strengthening. And strengthening of shear key has positive influence on the increase of bending stiffness.

• Nuclear Engineering and Technology
• /
• v.28 no.6
• /
• pp.583-593
• /
• 1996

An elastic stiffness formula of a leaf type holddown spring(HDS) assembly with a uniformly tapered width from $w_0$ to $w_14$ over the length, has been analytically derived based on Euler beam theory and Castigliano's theorem. Elastic stiffnesses of the tapered-width leaf type HDSs(TW-HDSs) designed in the same dimensional design spaces as the KOFA HDSs have been evaluated from the derived formula, in addition, a parametric study on the elastic stiffness of the TW-HDSs has been carried out. Analysis results show that, as the effects of axial and shear force on the elastic stiffness of He TW-HDSs have been 0.15~0.21% of the elastic stiffness, most of the elastic stiffness is attributed to the bending moment, and that elastic stiffnesses of the TW-HDSs have been about 32~33% higher than those of the KOFA HDSs. It is found that the number of leaves composing a HDS assembly could be lessened by one under the conditions that the TW-HDSs have been adopted in KOFA.

• Computers and Concrete
• /
• v.30 no.3
• /
• pp.175-183
• /
• 2022

To study the working mechanism and size effect of an innovative dovetail UHPC joint originated from the 5th Nanjing Yangtze River Bridge, a large-scale testing subject to negative bending moment was conducted and compared with the previous scaled specimens. The static responses, i.e., the crack pattern, failure mode, ductility and stiffness degradation were analyzed. It was found that the scaled specimens presented similar working stages and working mechanism with the large-scale ones. However, the post-cracking ductility and relative stiffness degradation all decrease with the enlarged length/scale, apart from the relative stiffness after flexural cracking. The slab stiffness at the flexural cracking stage is 90% of the initial stiffness while only 24% of the initial stiffness reserved in the ultimate stage. Finite element model (FEM) was established and compared with the experiments to verify its effectiveness in exploring the working mechanism of the innovative joint. Based on this effective method, a series of FEMs were established to further study the influence of material strength, pre-stressing level and ratio of reinforcement on its deflection-load relationship. It is found that the ratio of reinforcement can significantly improve its load-carrying capacity among the three major-influenced factors.

• Journal of the Korean Society for Precision Engineering
• /
• v.30 no.4
• /
• pp.434-441
• /
• 2013

Bending motion has been used in the surgical instruments with bending structures and tendon mechanisms. A simplified bending angle amplification ratio between the proximal and distal bending joint was derived in this article. The bending structure of disk and rib in the proximal joint was analyzed based on finite element method with an emphasis on the circumferential uniformity of bending stiffness. Regarding the distal joint, optimal design and sensitivity analysis was done with four design variables of outer and inner diameter, rib height and rib width while maximizing the deformation under the stress distribution below the yield stress. Outer diameter and rib width are most critical to maximum deformation as the outer diameter and inner diameters are so to maximum equivalent stress.

• Steel and Composite Structures
• /
• v.35 no.3
• /
• pp.371-384
• /
• 2020

The steel-concrete double composite girder in the negative flexural region combines an additional concrete slab to the steel bottom flange to prevent the local steel buckling, however, the additional concrete slab may lower down the neutral axis of the composite section, which is a sensitive factor to the tensile stress restraint on the concrete deck. This is actually of great importance to the structural rationality and durability, but has not been investigated in detail yet. In this case, a series of 5.5 m-long composite girder specimens were tested by negative bending, among which the bottom slab configuration and the longitudinal reinforcement ratio in the concrete deck were the parameters. Furthermore, an analytical study concerning about the influence of bottom concrete slab thickness on the cracking and sectional bending-carrying capacity were carried out. The test results showed that the additional concrete at the bottom improved the composite sectional bending stiffness and bending-carrying capacity, whereas its effect on the concrete crack distribution was not obvious. According to the analytical study, the additional concrete slab at the bottom with an equivalent thickness to the concrete deck slab may provide the best contributions to the improvements of crack initiation bending moment and the sectional bending-carrying capacity. This can be applied for the design practice.

• Elastomers and Composites
• /
• v.41 no.2
• /
• pp.125-130
• /
• 2006

To understand the effect of midsole on the bending stiffness of footwear, bending moment is studied with various hardness and thickness of polyurethane(PU) and poly(ethyl one-co-vinylacetate)(EVA) foams which composed in footwear midsole. The initial bending moment of footwear was appeared at $19^{\circ}$ on bending angle of footwear, and this bending angle was not depend on thickness and hardness of midsole. The bending moments of footwear were also increased with increase of the hardness and thickness of misole which were composed in footwear. Increased hardness and increased thickness of foam and midsole also cause a greater bending moment of the sports shoe, respectively.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2001.04a
• /
• pp.740-743
• /
• 2001

Sandwich structure is widely used in various fields of industry due to its excellent strength and stiffness compared with weight. We studied the sandwich structure which has honeycomb core type. We are concerned about its buckling and bending stress with respect to its side length, thickness and the height ratio of its unit core. After obtaining the buckling critical load of unit core, we applied it to the sandwich structure to observe the bending behavior. When we compared the buckling with bending stress under buckling critical load, we observed that models of which length ratio of unit honeycomb core, A, is lower than 0.04 and the thickness of core, t, is thicker than 0.09 mm, is subjected to the ultimate stress by bending before buckling.

• Journal of Fashion Business
• /
• v.15 no.3
• /
• pp.84-96
• /
• 2011

With the advancements in the computer graphics sectors, the visual quality of the virtual clothing implemented by using the 3-dimensional digital clothing software system has been much improved during the past decade. Most of the cloth simulation procedures are complicated due to the multitude of parameters involved in the simulation in order to achieve the appearance of the actual textile fabrics or the movement of the actual clothing as close as possible. Bending properties affect the tactile and visual qualities of the textile fabrics along with the shear and tensile properties. In this study, dynamic bending properties, focused on the movement of the textile fabrics including damping ratio and amplitude, were measured by using a dynamic bending test system.

• Steel and Composite Structures
• /
• v.48 no.3
• /
• pp.321-333
• /
• 2023

This paper proposes a comprehensive investigation on lateral stiffness of corner-supported steel modular frame using splice connection. A full-scale modular frame with two stacked steel modules under lateral load is tested. Ductile pattern in the transfer of lateral load is found in the final failure mode. Two types of lateral stiffness, including tangent stiffness and secant stiffness, are defined from the load-displacement due to the observed nonlinearity. The difference between these two types of stiffness is found around 20%. The comparisons between the experimental lateral stiffness and the predictions of classical methods are also conducted. The D-value method using hypothesis of independent case is a conservative option for predicting lateral stiffness, which is more recommended than method of contraflexural bending moment. Analyses on two classical short-rod models, including fix-rod model and pin-rod model, are further conducted. Results indicate that fix-rod model is more recommended than pin-rod model to simplify splice connection for simulation on lateral stiffness of modular frame in elastic design stage.