• International Journal of Concrete Structures and Materials
• /
• 제5권1호
• /
• pp.19-28
• /
• 2011

This paper documents an experimental study of dynamic response of reinforced concrete beams following instantaneous removal of a bearing column. Four half-scale specimens representing two-span beam bridging across the removed column were tested. The test boundary conditions simulated rotational and longitudinal restraints imposed on a frame beam by the neighboring structural components. The gravity loads were simulated by attaching mass blocks on the beams at three locations. Dynamic loading effects due to sudden removal of a column were simulated by quickly releasing the supporting force at the middle of the specimens. The experimental study investigated the load-carrying capacity of beams restrained longitudinally at the boundaries and dynamic impact on forces. The tests confirmed the extra flexural strength provided by compressive arch action under dynamic loading. The tests also indicated that the dynamic amplification effects on forces were much lower than that assumed in the current design guideline for progressive collapse.

• Structural Engineering and Mechanics
• /
• 제47권6호
• /
• pp.773-790
• /
• 2013

Bending behaviors of corroded reinforced concrete (RC) beams under repeated loading were investigated experimentally. A total of twenty test specimens, including four non-corrosion and sixteen corrosion reinforced concrete beams, were prepared and tested. A numerical model for flexural and cracking behaviors of the beam under repeated loading was also developed. Effects of steel corrosion on reinforced concrete beams regarding cracking, mid-span deflection, stiffness and bearing capacity of corroded beams were studied. The impact of corrosion on bond strength as the key factor was investigated to develop the computational model of flexural capacity. It was shown from the experimental results that the bond strength between reinforcement and concrete had increased for specimen of low corrosion levels, while this effect was changed when the corrosion level was higher. It was indicated that the bearing capacity of corrosion beam increased even at a corrosion level of about 5%.

• 한국식품영양학회지
• /
• 제8권2호
• /
• pp.110-115
• /
• 1995

This study was devised to observe the inhibitory effects of ethanol treatment precipitate (crude acidic polysaccharide) from Korean red ginseng on a lipolytic action of Toxohormone-L which has been known as lipolytic and anorexigenic factors. Toxohormone-L was obtained by partial purification of the ascites fluid from mice which had been inoculated with sarcoma-180. The yields of crude acidic polysaccharide from Korean red ginseng was 63.5%. In vitro, at the concentration of 500rg /ml, the inhibition rate of lipolysis by the crude acidic polysaccharide of Korean red ginseng was 38.8% and the total inhibitory activity per gram of ginseng material was 4,928 nit. In vivo, the red ginseng polysaccharide(40mg/ml in saline soon.) 16ul/g of body weight was injected to the sarcoma-180 bearing mice once In 3 days until death. The effects against the extension of life span was little but body weight gain of sarcoma-180 bearing mice decreased significantly by administration of Korean red ginseng polysaccharide compared to those of the control group.

• Structural Engineering and Mechanics
• /
• 제85권2호
• /
• pp.265-274
• /
• 2023

The spherical steel bearings (SSBs) has been gradually replaced traditional rubber bearings and extensively applied to high-speed railway (HSR) bridges in China, due to their durability and serviceability. Nevertheless, SSB is generally simplified to the ordinary constraints in the finite element model, which cannot reflect its detailed mechanical characteristics, especially its seismic performance. To provide a more precisely simulation, an innovative and simplified finite element simulation method is proposed and the combined element group is developed in ANSYS. The primary parameters were determined by means of the performance test of SSB. The finite element model of SSB applied to a single-span HSR simply supported girder bridge was established through the proposed method. The seismic performance of the SSB was further investigated. A shake table test was conducted to evaluate the accuracy of the proposed simulation method. It is found that the numerical results could have a good agreement with the experiment, namely, the proposed method is feasible and efficient.

• Steel and Composite Structures
• /
• 제18권5호
• /
• pp.1279-1290
• /
• 2015

The main role of studs, which act as connectors of the steel-concrete composite structures, is to ensure that the steel and the concrete work together as a whole. The studs in steel-concrete composite structures bear the shearing force in the majority of cases, but in certain locations, such as the mid-span of a simply supported composite beam, the studs bear axial uplift force. The previous studies mainly focused on the shearing performance of the stud by some experimental and theoretical effort. However, rare studies involved the uplift performance of studs. In this paper, the single stud uplift test on 10 composite specimens was performed. Meanwhile, based on the test, numerical analysis was introduced to simulate the concrete damage process due to the stud uplifted from concrete. The static ultimate bearing capacity, under which the stud connector was pulled out from the damaged reinforced concrete, is much larger than the cyclic ultimate bearing capacity, under which the weld joint between stud and steel plate fractured. According to the fatigue test results of 7 specimens, the fatigue S-N curve of the construction detail after minus 2 times standard deviation is $logN=24.011-9.171\;log{\Delta}{\sigma}$, the fatigue strength corresponding to $2{\times}10^6$ cycles is 85.33 MPa.

• Steel and Composite Structures
• /
• 제45권2호
• /
• pp.219-230
• /
• 2022

The aim of this paper is to study the mechanical behaviors of the cold-formed thin-walled steel and reinforced concrete sandwich composite slab (CTS&RC-SCS) under vertical loads and to develop the calculation methods of its flexural bearing capacity and section stiffness. Two CTS&RC-SCS specimens were designed and manufactured to carry out the static loading test, and meanwhile, the numerical simulation analyses based on finite element method were implemented. The comparison between experimental results and numerical analysis results shows that the CTS&RC-SCS has good flexural capacity and ductility, and the accuracy and rationality of the numerical simulation analysis are verified. Further, the variable parameter analysis results indicate that neither increasing the concrete strength grade nor increasing the thickness of C-sections can significantly improve the flexural capacity of CTS&RC-SCS. With the increase of the ratio of longitudinal bars and the thickness of the composite slab, the flexural capacity of CTS&RC-SCS will be significantly increased. On the basis of experimental research and numerical analysis above, the calculation formula of the flexural capacity of CTS&RC-SCS was deduced according to the plastic section design theory, and section stiffness calculation formula was proposed according to the theory of transformed section. In terms of the ultimate flexural capacity and mid-span deflection, the calculated values based on the formulas and the experimental values are in good agreement.

• Steel and Composite Structures
• /
• 제47권1호
• /
• pp.37-50
• /
• 2023

This paper presented an investigation into steel tubes encased high-strength concrete (STHC) composite walls, wherein steel tubes were embedded at the boundary elements of high-strength concrete walls. A series of cyclic loading tests was conducted to evaluate the failure pattern, hysteresis characteristics, load-bearing capacity, deformability, and strain distribution of STHC composite walls. The test results demonstrated that the bearing capacity and ductility of the STHC composite walls improved with the embedding of steel tubes at the boundary elements. An analytical method was then established to predict the flexural bearing capacity of the STHC composite walls, and the calculated results agreed well with the experimental values, with errors of less than 10%. Finally, a finite element modeling (FEM) was developed via the OpenSees program to analyze the mechanical performance of the STHC composite wall. The FEM was validated through test results; additionally, the influences of the axial load ratio, steel tube strength, and shear-span ratio on the mechanical properties of STHC composite walls were comprehensively investigated.

• Tribology and Lubricants
• /
• 제2권2호
• /
• pp.32-43
• /
• 1986

The mobility method is used for optimizing dynamically-loaded journal bearings. Connecting -rod bearings in both diesel and gasoline engines are optimized by parametric studies of bearing span and clearance. The inertia effect of the connecting-rod is also included in this study. Minimum film thickness, maximum film pressure, and friction loss are calculated to satisfy the design conditions in both engines.

• 한국콘크리트학회:학술대회논문집
• /
• 한국콘크리트학회 2009년도 춘계 학술대회 제21권1호
• /
• pp.581-582
• /
• 2009

Continuous deep girders which transmit the gravity load from the upper wall to lower columns have frequently long end shear spans between the boundary of the upper wall and the face of the lower column. This paper presents the results of tests and analyses performed on three 1:2.5 scale specimens with long end shear spans, (the ratios of shear-span/height : 2.0

• 토지주택연구
• /
• 제2권2호
• /
• pp.183-188
• /
• 2011

최근 건설되는 터널의 심도가 깊어져 난공사 구간이 증가되며, 초장대 터널의 증가로 터널 기술 개발이 필요해지고 있다. 터널의 기술개발의 하나로 터널 강지보재로 사용되는 높이 95mm 격자지보재에 사용되는 스파이더를 최적화하여 U자형과 보강재스파이더를 개발하였다. 개발된 격자지보재의 하중지지력을 평가하기 위하여 국내에서 사용되는 4절점 휨강도 실험을 실시하였으며 실내 실험을 위해 기존 격자지보재와 개발된 격자지보재의 시편을 직선으로 제작하여 실시하였다. 실험 결과 새로운 격자지보재는 기존의 격자지보재에 비하여 하중지지력이 높게 나타났다. 지지력 평가에 의한 시편의 응력-변형 거동을 분석한 결과 기존 격자지보재는 탄소성 거동이 나타났고, 새 격자지보재는 응력연화의 거동이 나타났다. 새 격자지보재는 하중이 가해지는 지점의 위치에 따라 지지력 거동이 달라짐을 알 수 있었다.