• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.48 no.11
• /
• pp.849-859
• /
• 2020

The semi-empirical equation and commercial computational tool were used to predict the base drag of a guided missile with free-stream Mach numbers and chamber pressures, and the results were generally agree each other. Differences in flow characteristics and base drags were observed with over/under expansion conditions by the nozzle. Under the over-expansion condition, the base pressure decreased as the expansion fan was generated at upper region of the base, and base pressure decreased further with increasing free-stream Mach number as the expansion becomes strong. Under the under-expansion conditions, a shock wave was generated around the base by the influence of the nozzle flow, which increased the base pressure, and the effect increased as the chamber pressure increased. Under the same chamber pressure condition, as the free-stream Mach number increases, the characteristic that the base pressure decreases as the shock wave generated at the base moves downstream was observed.

• Journal of the Korea Institute of Military Science and Technology
• /
• v.27 no.1
• /
• pp.31-42
• /
• 2024

In this study, the methodology of determination of base bleed motor data for base bleed projectile based on the NATO standard trajectory model, especially STANAG 4355 Method 2 were presented. Ground combustion experiments and aerodynamic performance firing tests were conducted to determine the drag reduction motor data of the base bleed projectile and this data was described based on the NATO standard ballistic model. The derived drag reduction motor data were input into the ballistic equations to complete the ballistic model and it was confirmed that the calculated predicted trajectory from the ballistic model matched well with the measured trajectory from the aerodynamic performance firing tests.

• Wind and Structures
• /
• v.11 no.4
• /
• pp.257-273
• /
• 2008

A number of passive aerodynamic drag reduction methods were applied separately and then in different combinations on an intercity bus model, through wind tunnel studies on a 1:20 scale model of a Mercedes Benz Tourismo 15 RHD intercity bus. Computational fluid dynamics (CFD) modelling was also conducted in parallel to assist with flow visualisation. The commercial CFD package $CFX^{TM}$ was used. It has been found that dramatic reductions in coefficient of drag ($C_D$) of up to 70% can be achieved on the model using tapered and rounded top and side leading edges, and a truncated rear boat-tail. The curved front section allows the airflow to adhere to the bus surfaces for the full length of the vehicle, while the boat-tails reduce the size of the low pressure region at the base of the bus and more importantly, additional pressure recovery occurs and the base pressures rise, reducing drag. It is found that the CFD results show remarkable agreement with experimental results, both in the magnitude of the force coefficients as well as in their trends. An analysis shows that such a reduction in aerodynamic drag could lead to a significant 28% reduction in fuel consumption for a typical bus on intercity or interstate operation. This could translate to a massive dollar savings as well as significant emissions reductions across a fleet. On road tests are recommended.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.28 no.2
• /
• pp.127-134
• /
• 2004

Control of drag force on a circular cylinder using multiple detached splitter plates is numerically studied for laminar flow Two splitter plates with the same length as the cylinder diameter (d) are placed horizontally in the upstream of the cylinder and in the near-wake region, respectively. Their positions are described by the gap ratios (G$_1$/d, G$_2$/d), where G$_1$ represents the gap between the cylinder stagnation point and the rear edge of the upstream splitter plate, and G$_2$ represents the gap between the cylinder base point and the leading edge of the rear splitter plate. The drag varies with the two gap ratios; it has the minimum value at a certain set of gap ratios for each Reynolds number The upstream splitter plate decreases the stagnation pressure, while the rear splitter plate increases the base pressure by suppressing vortex shedding. This combined effect causes a significant drag reduction on the cylinder Particularly, the drag sharply increases past an optimum G$_2$/d; this seems to be related to a sudden change in bubble size in the wake region.

• Journal of the Society of Naval Architects of Korea
• /
• v.49 no.6
• /
• pp.512-520
• /
• 2012

In this study, the numerical analysis for the flows around an axial cylinder is carried out in order to investigate the basic characteristics of drag of blunt body. A variation of drag and flow separation for the axial cylinder is investigated according to the length-diameter ratio. Also, the flow separation around the head is removed by rounding-off the front edge of the body to analyze the effect of drag reduction. Most of the drag turns out to be a pressure drag component and the variation of drag is caused by the change of pressure and velocity which is affected strongly by the flow separation at the edges of the axial cylinder. Especially, it is found that the pressure drag component acting on the back of axial cylinder, as known as the base drag, mainly changes the drag. As the length-diameter ratio of axial cylinder increases, the drag sharply decreases and the minimum is shown when the length-diameter ratio is about 2.4. Also, as the length-diameter ratio increases further above 2.4, the drag increases at a slower rate. The pressure drag is almost constant when the length-diameter ratio is greater than 8, but the increase of friction drag component is the reason for the increase of the drag. When flow separation is removed completely at the front edge of the axial cylinder, the pressure drag component is reduced to 12~17%, but the total drag is reduced to only 17%~32% due to the friction drag component that increases linearly proportional to the length-diameter ratio.

• Particle and aerosol research
• /
• v.9 no.4
• /
• pp.271-277
• /
• 2013

This article reports the drag reduction phenomenon of aqueous suspensions containing carbon nanotubes (CNTs) flowing through horizontal tubes. Stable nanofluids were prepared by using a surfactant. It is found that the drag forces of CNT nanofluids were reduced at specific flow conditions compared to the base fluid. It is found that the friction factor of CNT nanofluids was reduced up to approximately 30 % by using CNT nanofluids. Increased kinematic viscosities of CNT nanofluids are suggested to the key factors that cause the drag reduction phenomenon. In addition, transition from laminar to turbulent flow is observed to be delayed when CNT nanofluids flow in a horizontal tube, meaning that drag reduction occurs at higher flow rates, that is, at higher Reynolds numbers.

• Journal of computational fluids engineering
• /
• v.8 no.3
• /
• pp.7-11
• /
• 2003

Accurate assessment of the effect of jet plume on the boattail pressure drag of transonic airbreathing missiles is very important to reduce drag and to satisfy the flight range and the required maneuver. Numerical results of drag analysis for boattail and base pressures due to jet plume are presented considering the turbulence modeling. Drag assessment due to the size of jet plume, the conditions of the exhaust gas, the configurations of the boattail, and transonic mach numbers is included.

• Journal of Mechanical Science and Technology
• /
• v.15 no.10
• /
• pp.1434-1441
• /
• 2001

A computational study has been performed to determine the effects of divergent trailing edge (DTE) modification to a supercritical airfoil in transonic flow field. For this, the computational result with the original DLBA 186 supercritical airfoil was compared to that of the modified DLBA 283. A wavier-Stokes code, Fluent 5. 1, was used with Spalart-Allmaras's one-equation turbulence model. Results in this study showed that the reduction in drag due to the DTE modification is associated with weakened shock and delayed shock appearance. The decrease in drag due to the DTE modification is greater than the increase in base drag. The effect of the recirculating flow region on lift increase was also observed. An airfoil with DTE modification achieved the same lift coefficient at a lower angle of attack while giving a lower drag coefficient. Thus, the lift-to-drag ratio increases in transonic flow conditions compared to the original airfoil. The lift coefficient increases considerably whereas the lift slope increases just a little due to DTE modification.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.18 no.10
• /
• pp.2664-2674
• /
• 1994

Drag, lift, and pitching moment measurements have been made on a range of slanted-base ogive cylinders, using the KANOMAX wind tunnel and balance system. Test Reynolds numbers(based on model maximum diameter) varied from $0.54{\times}10^{5}{\;}to{\;}1.56{\times}10^{5}$. Crossflow velocity maesurement was conducted by 5-hole pitot tube at $Re_{D}=1.46{\times}10^{5}$. For two base angle $({\theta}=30$ and 45 deg.), aerodynamic forces and moment were measured with increasing angle of attack(0~30 deg.). Two types of wake flow were observed, a quasisymetric turbulent closure or a longitudinal vortex flow. Aerodynamic characteristics differ dramatically between the two wake types. It was found that the drag, lift and pitching moment coefficients increased with increasing angle of attack.

• Journal of computational fluids engineering
• /
• v.20 no.2
• /
• pp.16-22
• /
• 2015

The pressure is generally lower than that of the freestream at the base of a missile body due to the energy loss by the flow separation around the edge of the base. The base pressure changes in the presence of the thrust jet due to the interaction between the base flow of the missile and the jet flow. In this study, behavior of the missile base pressure by the change of the jet exit pressure and the freestream condition is investigated using the CFD(Computational Fluid Dynamics) method. Effects of the grid type and the freestream condition are tested. The results are compared with the semi-empirical predictions and the flight test data. The CFD results agree well with the flight test data. The semi-empirical predictions overestimate the base pressure when jet thrust is strong for low freestream speed.