• Proceedings of the Korean Society of Laser Processing Conference
• /
• 2006.11a
• /
• pp.41-45
• /
• 2006

Auto focusing system to find optimized focal position of laser beam used for material process has been investigated by using fiber confocal method. Wavelength of laser diode (LD) and diameter of single-mode fiber we 780nm and $5.3{\mu}m$, respectively. Intensity distributions of beam reflected from the surface of mirror and silicon bare wafer have been observed in a gaussian form. Experimental results show that focal position obtained by LD is shifted from one observed from surface scribed by laser about $80{\mu}m$. It is due to the difference of wavelength and each divergence of between LD and laser used for material process. It is confirmed that auto focusing control system through position calibration has operated steadily.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.16 no.8
• /
• pp.657-662
• /
• 2003

This paper presents a new fabrication method of selective SiGe epitaxial growth at 650 $^{\circ}C$ on (100) silicon wafer with oxide patterns by reduced pressure chemical vapor deposition. The new method is characterized by a cyclic process, which is composed of two parts: initially, selective SiGe epitaxy layer is grown on exposed bare silicon during a short incubation time by SiH$_4$/GeH$_4$/HCl/H$_2$system and followed etching step is achieved to remove the SiGe nuclei on oxide by HCl/H$_2$system without source gas flow. As a result, we noted that the addition of HCl serves not only to reduce the growth rate on bare Si, but also to suppress the nucleation on SiO$_2$. In addition, we confirmed that the incubation period is regenerated after etching step, so it is possible to grow thick SiGe epitaxial layer sustaining the selectivity. The effect of the addition of HCl and dopants incorporation was investigated.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2010.02a
• /
• pp.390-390
• /
• 2010

Superconducting proximity effects of Nb/Si(111) were investigated with scanning tunneling microscopy(STM) and scanning tunneling spectroscopy(STS). A highly-doped($0.002\;{\omega}{\diamondsuit}cm$) Si wafer pieces were used as substrate and Nb source was thermally evaporated onto the atomically clean silicon substrate. The temperature of the silicon sample was held at $600^{\circ}C$ during the niobium deposition. And the sample was annealed at $600^{\circ}C$ for 30 minutes additionally. Volmer-Weber growth mode is preferred in Nb/Si(111) at the sample temperature of $600^{\circ}C$. With proper temperature and annealing time, we can obtain Nb islands of lateral size larger than Nb coherence length(~38nm). And outside of the islands, bare Si($7{\times}7$) reconstructed surface is exposed due to the Volmer-Weber Growth mode. STS measurement at 5.6K showed that Nb island have BCS-like superconducting gap of about 2mV around the Fermi level and the critical temperature is calculated to be as low as 6.1K, which is lower than that of bulk niobium, 9.5K. This reduced value of superconducting energy gap indicates suppression of superconductivity in nanostructures. Moreover, the superconducting state is extended out of the Nb island, over to bare Si surface, due to the superconducting proximity effect. Spatially-resolved scanning tunneling spectroscopy(SR-STS) data taken over the inside and outside of the niobium island shows gradually reduced superconducting gap.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2013.08a
• /
• pp.266.2-266.2
• /
• 2013

According to advanced nanotechnology, the nanostructured materials with various kinds and shape are synthesized easily or produced by process. Recently, researches about interaction between the nanostructured materials and biological system have been progressed actively. The surface topography may influence cellular responses, for example cell adhesion, cell morphology. In this work, we synthesized vertically aligned silicon nanowires (SiNWs) on the Au-covered Si(111) wafer by chemical vapor deposition (CVD) method. We accomplished to control of the SiNWs diameter by regulating thickness of Au film such as 1 nm and 10 nm. These substrates did not isolate cells and just provided surface topography for cell culture. Human Embryonic Kidney 293T cells (HEK 293T cells) were cultured on these substrates for 2 days. We studied the nanotopographical effects on cell morphology, adhesion, and growth which are evaluated on each SiNWs substrate comparing bare glass as control.

• Journal of the Korean Vacuum Society
• /
• v.20 no.3
• /
• pp.225-232
• /
• 2011

Reactive ion etching (RIE) technique for maskless surface texturing of mc-silicon solar wafers has been applied and succeed in fabricating a grass-like black-silicon with an average reflectance of $4{\pm}1%$ in a wavelength range of 300~1,200 nm. In order to investigate the optimized texturing conditions for mass production of high quantum efficiency solar cell Surface characteristics such as the spatial distribution of average reflectance, micrscopic surface morphology and minority carrier lifetime were monitored for samples from saw-damaged $15.6{\times}15.6\;cm^2$ bare wafer to key-processed wafers as well as the mc-Si solar cells. We observed that RIE textured wafers reveal lower average reflectance along from center to edges by 1% and referred the origin to the non-uniform surface structures with a depth of 2 times deeper and half-maximum width of 3 times. Samples with anti-reflection coating after forming emitter layer also revealed longer minority carrier lifetime by 40% for the edge compared to wafer center due to size effects. As results, mc-Si solar cells with RIE-textured surface also revealed higher efficiency by 2% and better external quantum efficiency by 15% for edge positions with higher height.

• Journal of the Korean Ceramic Society
• /
• v.31 no.7
• /
• pp.795-803
• /
• 1994

Ferroelectric BaTiO3 thin film was produced using BaTi-ethoxide sol. This sol was prepared from BaTi-ethoxide by a partial hydrolysis with ammonia as a basic catalyst and ethylene glycol as a chelating agent. BaTiO3 thin film was prepared from three continuous spin-coating layers of the sol on bare Si(100) wafer at 2500 rpm followed by pyrolysis at $700^{\circ}C$ for 30 min. After the heat treatment, the film was 0.200$\pm$0.010 ${\mu}{\textrm}{m}$ thick and its grain size was 0.059 ${\mu}{\textrm}{m}$. On the other hand, electrical properties were measured for BaTiO3 thin film separately prepared on Au-deposited silicon wafer. The dielectric constant and loss of the BaTiO3 thin film at room temperature was 150~160 and 0.04 respectively, which was measured at 10 kHz and oscillation level of 0.1 V. In the measurements of the dielectric properties at high temperatures, it was observed that the capacitance of the thin film increases steeply, while the dielectric loss reaches maximum around 1$25^{\circ}C$, which corresponds a phase transition from tetragonal to cubic BaTiO3.

• Tribology and Lubricants
• /
• v.18 no.1
• /
• pp.1-8
• /
• 2002

Nano adhesion and friction between a $Si_{3}N_{4}$ AFM(atomic force microscope) tip and thin silver films were experimentally studied. Tests were performed to measure the nano adhesion and friction in both AFM and LFM(lateral force microscope) modes in various range of normal loads. Thin silver films deposited by IBAD (ion beam assisted deposition) on Si-wafer (100) and other Si-wafers of different surface roughness were used. Results showed that nano adhesion and friction decreased with the surface roughness. When the Si surfaces were coated by pure silver, the adhesion and friction decreased. But the adhesion and friction were not affected by the thickness of IBAD silver coating. As the normal force increased, the adhesion forces of bare Si-wafer and IBAD silver coating film remained constant, but the friction forces increased linearly. Test results suggested that the friction was mainly governed by the adhesion as long as the load was low.

• Journal of the Korean Applied Science and Technology
• /
• v.16 no.1
• /
• pp.33-40
• /
• 1999

We used Cu as a representative of metals to be directly adsorbed on the bare Si surface and studied its removal DHF, DHF-$H_2O_2$ and BHF solution. It has been found that Cu ion in DHF adheres on every Si wafer surface that we used in our study (n, p, n+, p+) especially on the n+-Si surface. The DHF-$H_2O_2$ solution is found to be effective in removing metals featuring high electronegativity such as Cu from the p-Si and n-Si wafers. Even when the DHF-$H_2O_2$ solution has Cu ions at the concentration of 1ppm, the solution is found effective in cleaning the wafer. In the case the n+-Si and p+-Si wafers, however, their surfaces get contaminated with Cu When Cu ion of 10ppb remains in the DHF-$H_2O_2$ solution. When BHF is used, Cu in BHF is more likely to contaminate the n+-Si wafer. It is also revealed that the surfactant added to BHF improve wettability onto p-Si, n-Si and p+-Si wafer surface. This effect of the surfactant, however, is not observed on the n+-Si wafer and is increased when it is immersed in the DHF-$H_2O_2$ solution for 10min. The rate of the metallic contamination on the n+-Si wafer is found to be much higher than on the other Si wafers. In order to suppress the metallic contamination on every type of Si surface below 1010atoms/cm2, the metallic concentration in ultra pure water and high-purity DHF which is employed at the final stage of the cleaning process must be lowered below the part per trillion level. The DHF-$H_2O_2$ solution, however, degrades surface roughness on the substrate with the n+ and p+ surfaces. In order to remove metallic impurities on these surfaces, there is no choice at present but to use the $NH_4OH-H_2O_2-H_2O$ and $HCl-H_2O_2-H_2O$ cleaning.

• Journal of Sensor Science and Technology
• /
• v.24 no.4
• /
• pp.264-269
• /
• 2015

An infrared (IR) bolometer measures the change of resistance by absorbing incident IR radiation and generates a signal as a function of the radiation intensity. Since a bolometer requires temperature stabilization and light filtering except for the infrared rays, it is essential for the device to be packaged meeting conditions that above mentioned. Minimization of heat loss is needed in order to stabilize temperature of bolometer. Heat loss by conduction or convection requires a medium, so the heat loss will be minimized if the medium is a vacuum. Therefore, vacuum packaging for bolometer is necessary. Another important element in bolometer packaging is germanium (Ge) window, which transmits IR radiation to heat the bolometer. To ensure a complete transmittance of IR light, anti-reflection (AR) coatings are deposited on both sides of the window. Although the transmittance of Ge window is high for IR rays, it is difficult to use frequently in low-price IR bolometer because of its high price. In this paper, we fabricated IR window by utilizing silicon (Si) substrate instead of Ge in order to reduce the cost of bolometer packaging. To enhance the IR transmittance through Si substrate, it is textured using Reactive Ion Etching (RIE). The texturing process of Si substrate is performed along with the change of experimental conditions such as gas ratio, pressure, etching time and RF power.

• Journal of the Korean Vacuum Society
• /
• v.2 no.4
• /
• pp.416-423
• /
• 1993

Hydrogen depth profiling was performed by H(19F, $\alpha$${\gamma}$) nuclear resonance reactin . A cesium sputtering ion sorce and 1.7MV Tandem Van de Graaff accelerator was used for the production of 6.5MeV 19F ion. The ${\gamma}$ rays produced by the reaction were measure dby 3" $\times$3" and 6" $\times$8" Nal detectors . A test measurement was done for hydrogen contaminatin layer of a bare silicon wafer, Si3N4(H) and Zr(O)a-Si/Si for the purpose of verifying the applicability , detection limit and the reliability of the method.ility of the method.