• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.26 no.4
• /
• pp.787-793
• /
• 2002

In this study, a bar impact test of low velocity was carried out to gain an insight into the damage mechanism and sequence induced in alumina plates(AD 85 and AD 90) under impact conditions. An experimental setup utilizing an instrumented long bar impact was devised, that can measure directly the impact force applied to the specimen and supply a compressive contact pressure to the specimen. During the bar impact testing, the influences of the contact pressure applied along the impact direction to the specimen on the fracture behavior were investigated. The measured impact force profiles explained well the damage behavior induced in alumina plates. The higher contact pressure to the specimen led to the less damage due to the suppression of radial cracks due to the increase in the apparent flexural stiffness of plate. It had produced the change of damage pattern developed in the specimen; from the radial cracks to the local contact stress dominant damage. It would contribute to the improvement of the ballistic property in ceramic plates. The observed results showed the following sequence in damage developed: The development of cone crack at impact region, the formation of radial cracks from the rear surface of plate depending on the plate thickness, the occurrence of crushing within the cone envelope and the fragmentation.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.19 no.3
• /
• pp.20-28
• /
• 2015

Performance parameters of solid rocket motor with multi axis pintle nozzles were analyzed theoretically and modeled. For figuring out the governed variable of dynamic characteristics of system, dynamic analysis was done by using established model. To present characteristics of this system, the model should include not only internal ballistics of propulsion unit but also actuating system to move pintle. For solid rocket motor with multi axis pintle nozzles, not only performance of steady state but also dynamic characteristic of transient state is important design parameter to precise thrust control. Therefore, response time of open-loop system was analyzed by using established model and requirement about response time was satisfied by controlling pressure.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.15 no.3
• /
• pp.47-57
• /
• 2011

All solid rocket propellants are divided in two basic classes according to chemical state: homogeneous(double base) and heterogeneous (composite). Today, composite propellants are extensively used as power sources covering the range from gas generators and small rocket systems to large launch vehicles in space programs. The development of composite rocket propellants in the past was mainly directed to thermoset polymers. But, the thermoset composite propellants have the complication in formulation and fabricating process to adapt to rocket system requirements. In contrast to the thermoset propellant, the PVC plastisols composite propellants have the advantages in the view of loss in manufacturing process, low cost of raw material, and stability of the handling process even though moderate ballistic and mechanical properties. It is predicted that the application field of this class will be used more widely than any other classes.

• Journal of the Korea Institute of Military Science and Technology
• /
• v.22 no.3
• /
• pp.299-310
• /
• 2019

Increase of combat capability through the lightweighting of vehicles has been internationally issued. One of the methods for lightening is applying high hardness armor(HHA) steel which is outstanding ballistic performance and protection performance compared to weight. Development of HHA steel is currently completed in America, United Kingdom, Australia and Germany. It is used for not only combat vehicle, but also various combat device. Korea is developing new material of HHA steel according to this trend. When such HHA steel is applied to structure, welding process is used for connection of the structure. Cracks from hydrogen embrittlement and cold cracking are easily generated in welds of HHA steel and it greatly affects the strength of all structure. Decrease of strength from welding defect is critical to combat capability. Therefore, welding process optimization is important for performing the role of structure. In this study, international welding technology is reviewed through scientific research paper and patent.

• Composites Research
• /
• v.32 no.2
• /
• pp.120-126
• /
• 2019

Advanced fiber fabrics have been utilized in not only anti-stabbing and bullet-proofing for body armor but also various industrial fields including vehicular armor and spacecraft structure. Furthermore, there have been a number of research to improve the ballistic performance of advanced fabrics introducing many computational approaches. In our research, an advanced fabric, Heracron manufactured in South Korea was modelled firstly using Autodyn, a commercial software specializing in impact and explosion phenomenon. The sensitivity of the input parameters was also confirmed by conducting simulations. To verify the numerical modelling, we measured and compared the simulation results with velocity decrements after impact involving one, three, and five layers of Heracron under 200-500 m/s impacts by an aluminum spherical projectile. The Heracron fabric was successfully modelled using Autodyn.

• Korean Journal of Materials Research
• /
• v.29 no.1
• /
• pp.43-51
• /
• 2019

Nacre of abalone shell features a "brick-and-mortar" microstructure, in which micro-plates of calcium carbonate are bonded by nanometers-thick layers of chitin and proteins. Due to the microstructure and its unique toughening mechanisms, nacre possesses an excellent combination of specific strength, stiffness and toughness. This study deals with the possibility of using nacre fragments obtained from abalone shell for making a bulletproof armor system. A composite plate laminated with abalone shell fragments is made and compression and bend tests are carried out. In addition, a bulletproof test is performed with hybrid armor systems which are composed of an alumina plate, a composite plate, and aramid woven fabric to verify the ballistic performance of nacre. The compressive strength of the composite plate is around 258.3 MPa. The bend strength and modulus of the composite plate decrease according to the plate thickness and are about 149.2 MPa and 50.3 GPa, respectively, for a 4.85 mm thick plate. The hybrid armor system with a planar density of $45.2kg/m^2$, which is composed of an 8 mm thick alumina plate, a 2.4 mm thick composite plate, and 18 layers of aramid woven fabric, satisfy the NIJ Standard 0101.06 : 2008 Armor Type IV. These results show that a composite plate laminated with abalone shell fragments can be used for a bulletproof armor system as an interlayer between ceramic and fabric to decrease the armor system's weight.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.22 no.1
• /
• pp.338-344
• /
• 2021

In this study, an actual test procedure was considered for the effective operation of a bulletproof test. The problems of the existing system were drawn in two ways. First, it is difficult to mount items of various shapes. Second, various test standards cannot be applied. To improve these problems, an automated and standardized mounting system was designed/applied to mount various items. The multi-purpose mount was compatible with the backing support for body armor testing. The sample holding frame was located inside and was designed to mount samples of various sizes and shapes through vertical movement and fixation without a separate detachment/attachment process. A comparison of the economics before and after the introduction of the item mounting system confirmed the effectiveness of the system by the increased number of daily tests and equipment utilization and reduced hourly cost.

• Journal of Advanced Navigation Technology
• /
• v.26 no.5
• /
• pp.281-288
• /
• 2022

This study quantitatively analyzed the human casualties that can occur when a multicopter-type Urban Air Mobility (UAM) with a weight of about 1 ton and a speed of about 100 km/h falls in an urban area. Based on the population density and building database in Seoul, the population exposed to collisions in the event of a UAM crash was derived. Through the ballistic descent model, the accident impact radius of the UAM fall was calculated. In addition, the change in human casualties on the ground was analyzed when the accident impact radius increased. Finally, the ground risk map was created for Seoul, and it was confirmed that about 1 to 10 people could be injured when a UAM crash.

• Journal of Trauma and Injury
• /
• v.36 no.4
• /
• pp.421-424
• /
• 2023

This case report presents the case of a 49-year-old man who presented to our level I trauma center after sustaining injuries in an altercation with local law enforcement in which he was shot with a less lethal bean bag and tased. In a primary survey, a penetrating left supraclavicular wound was noted in addition to a taser dart lodged in his flank. No other traumatic findings were noted in a secondary survey. Given hemodynamic stability, completion imaging was obtained, revealing a foreign body in the left lung, a left open clavicle fracture, a C5 tubercle fracture, a possible grade I left vertebral injury, and a left first rib fracture. Soft tissue gas was seen around the left subclavian and axillary arteries, although no definitive arterial injury was identified. The bean bag projectile was embedded in the parenchyma of the left lung on cross-sectional imaging. The patient underwent thoracotomy for removal of the projectile and hemostasis. A thoracotomy was chosen as the operative approach due to concerns about significant bleeding upon foreign body removal. A chest tube was placed and subsequently removed on postoperative day 5. The patient was discharged on postoperative day 7. At a 2-week outpatient follow-up visit, the patient was doing well. This case report is the first to describe this outcome for a drag-stabilized bean bag. Although law enforcement officers utilize bean bag projectiles as a "less lethal" means of crowd control and protection, these ballistics pose significant risk and can result in serious injury.

• Journal of Astronomy and Space Sciences
• /
• v.40 no.4
• /
• pp.199-215
• /
• 2023

The Korea Pathfinder Lunar Orbiter (KPLO), the first South Korea lunar exploration probe, successfully arrived at the Moon on December, 2022 (UTC), following a 4.5-month ballistic lunar transfer (BLT) trajectory. Since the launch (4 August, 2022), the KPLO magnetometer (KMAG) has carried out various observations during the trans-lunar cruise phase and a 100 km altitude lunar polar orbit. KMAG consists of three fluxgate magnetometers capable of measuring magnetic fields within a ± 1,000 nT range with a resolution of 0.2 nT. The sampling rate is 10 Hz. During the originally planned lifetime of one year, KMAG has been operating successfully while performing observations of lunar crustal magnetic fields, magnetic fields induced in the lunar interior, and various solar wind events. The calibration and offset processes were performed during the TLC phase. In addition, reliabilities of the KMAG lunar magnetic field observations have been verified by comparing them with the surface vector mapping (SVM) data. If the KPLO's mission orbit during the extended mission phase is close enough to the lunar surface, KMAG will contribute to updating the lunar surface magnetic field map and will provide insights into the lunar interior structure and lunar space environment.