• 한국세라믹학회지
• /
• 제28권7호
• /
• pp.517-524
• /
• 1991

The CVD process of BPSG (BoroPhosphoSilicate Glass) and its thin film properties were studied. B2H6, PH3, SiH4 and O2 gases were reacted in a AP (Atmospheric Pressure) CVD system in the temperature range of 300℃ and 460℃. The interaction of B2H6 and PH3 was studied from the deposition rate and dopant incorporation change point of view. The dependency of BPSG step coverage on the temperature was changed with different O2/(B2H6+PH3+SiH4) ratio. Finally, the boundary which distinguishes the stable BPSG's from the ones that react with Di (Deionized) water or cleaning chemicals such as H2SO4, HCl, H2O2, NH4OH etc could be defined.

• 대한전자공학회:학술대회논문집
• /
• 대한전자공학회 2002년도 하계종합학술대회 논문집(2)
• /
• pp.225-228
• /
• 2002

The adhesion effect between the oxide layer and the metal layer has been studied by RTP anneal. Two types of oxides, BPSG and P-TEOS, were used as a bottom layer under multi-layered metal film. We observe the interface between oxide and metal layer using SEM (scanning electron microscopy), TEM (transmission electron microscopy), AES (auger electron spectroscopy). Adhesion failure was occurred by interfacial reaction between the BPSG oxide and the multi-layered metal film at 650"C RTP anneal. The phosphorus rich layer was observed at interface between BPSG oxide and metal layer by AES and TEM measurements. On the other hand adhesion was a)ways good in the sample used P-TEOS oxide as a bottom layer. We have known that adhesion between BPSG and multi-layered metal film was improved when the sample was annealed below $650^{\circ}C$.TEX>.

• JSTS:Journal of Semiconductor Technology and Science
• /
• 제13권6호
• /
• pp.662-667
• /
• 2013

The effect of fluorine ions, which can be reacted with boron in high-doped BPSG, is investigated on the contact sidewall wiggling profile in semiconductor process. In the semiconductor device, there are many contacts on $p^+/n^+$ source and drain region. However these types of wiggling profile is only observed at the $n^+$ contact region. As a result, we find that the type of plug implantation dopant can affect the sidewall wiggling profile of contact. By optimizing the proper fluorine gas flow rate, both the straight sidewall profile and the desired electrical characteristics can be obtained. In this paper, we propose a fundamental approach to improve the contact sidewall wiggling profile phenomena, which mostly appear in high-doped BPSG on next-generation DRAM products.

• 청정기술
• /
• 제18권3호
• /
• pp.280-286
• /
• 2012

초임계 이산화탄소를 이용하여 희생 $SiO_2$층에 대한 건식 식각 실험을 진행하였다. HF/pyridine (HF/py) 식각액과 알콜 첨가제를 사용하여 이중 챔버 시스템 방식으로 boron phosphor silica glass (BPSG), tetraethyl orthosilicate (TEOS), thermal $SiO_2$와 Si-nitride (SiN)의 박막 층에 대한 식각 성능을 조사하였다. 메탄올의 첨가에 의하여 실리카 희생막에 대한 HF/py의 식각률이 높아지는 것을 확인할 수 있었다. BPSG를 제외하고는 메탄올이 가장 높은 식각률을 보여줬지만, BPSG의 SiN에 대한 식각 선택비는 이소프로판올이 가장 높았다. HF/py/MeOH 계의 건식 식각반응에서 반응 온도에 따라서 박막별 식각률이 증가하였다. 특히 반응 온도 증가에 따라 BPSG의 식각 속도의 증가폭이 매우 높게 나타났다. HF/py에 알콜 공용매를 첨가하여도 식각 부산물 감소에는 크게 효과가 없었다. HF/$H_2O$의 식각률이 HF/py/alcohol 보다 높게 나타났지만 HF/$H_2O$에 알콜 공용매를 첨가하였을 때는 오히려 식각률이 감소되었다. 캔틸레버 빔 구조를 초임계 이산화탄소 건식 식각으로 제조하여 높은 종횡비의 패턴구조물을 손상 없이 성공적으로 식각할 수 있었다.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2001년도 춘계학술대회 논문집 반도체재료
• /
• pp.38-41
• /
• 2001

In this work, we have been studied the characteristics of each nitride film for the optimization of PMD(pre-metal dielectric) liner nitride process, which can applicable in the recent semiconductor manufacturing process. The deposition conditions of nitride film were splited by PO (protect overcoat) nitride, baseline, low hydrogen, high stress and low hydrogen, respectively. And also we tried to catch hold of correlation between BPSG(boro-phospho silicate glass) deposition and densification. Especially, we used FTIR area method for the analysis of density change of Si-H bonding and Si-NH-Si bonding, which decides the characteristics of nitride film. To judge whether the deposited films were safe or not, we investigated the crack generation of wafer edge after BPSG densification, and the changes of nitride film stress as a function of RF power variation.

• 한국전기전자재료학회논문지
• /
• 제13권2호
• /
• pp.131-136
• /
• 2000

We have investigated the slurry induced metallic contaminations of undoped and doped silicate oxides surface on CMP cleaning process. The metallic contaminations by CMP slurry were evaluated in four different oxide films, such as plasma enhanced tetra-ethyl-orthyo-silicate glass(PE-TEOS), O3 boro-phos-pho-silicate glass(O3-BPSG), PE-BPSG, and phospho-silicate glass(PSG). All films were polished with KOH-based slurry prior to entering the post-CMP cleaner. The Total X-Ray fluorescence(TXRF) measurements showed that all oxide surfaces are heavily contaminated by potassium and calcium during polishing which is due to a CMP slurry. The polished O3-BPSG films presented higher potassium and calcium contaminations compared to PE-TEOS because of a mobile ions gettering ability of phosphorus. For PSG oxides, the slurry induced mobile ion contamination increased with an increase of phosphorus contents. In addition, the polishing removal rate of PSG oxides had a linear relationship as a function of phosphorus contents.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2001년도 하계학술대회 논문집
• /
• pp.347-350
• /
• 2001

A typical Mold method is to form a gate electrode, a gate oxide, and emitter tip after fabrication of mold shape using wet-etching of Si substrate. In this study, however, new Mold method using a side wall space structure is used in order to make sharper emitter tip with a gate electrode. Using LPCVD(low pressure chemical vapor deposition), a gate oxide and electrode layer are formed on a Si substrate, and then BPSG(Boro phospher silicate glass) thin film is deposited. After, the BPSG thin film is flowed into a mold as high temperature in order to form a sharp mold structure. Next TiN thin film is deposited as a emitter tip substance. The unfinished device with a glass substrate is bonded by anodic bonding techniques to transfer the emitters to a glass substrate, and Si substrate is etched using KOH-deionized water solution. Finally, we made sharp field emitter array with gate electrode on the glass substrate.

• 한국전기전자재료학회논문지
• /
• 제14권10호
• /
• pp.779-784
• /
• 2001

In this work, we studied the characteristics of nitride films for the optimization of PMD(pro-metal dielectric) linear process, which can be applied to the recent semiconductor manufacturing process. We split the deposit condition of nitride films into four parts such as PO(protect overcoat) nitride, baseline, low hydrogen and high stress and low hydrogen, respectively. We tried to find out correlation between BPSG deposition and densification. In order to analyze the changes of Si-H and Si-NH-Si bonding density, we used FTIR area method. We also investigated the crack generation on wafer edge after BPSG densification, and the changes of nitride film stress as a function of RF power variation to judge whether the deposited films.

• 한국입자에어로졸학회지
• /
• 제6권3호
• /
• pp.139-145
• /
• 2010

In this study, we investigated the particle formation during the deposition of borophosphosilicate glass (BPSG) and phosphosilicate glass (PSG) films in thermal chemical vapor deposition reactor using in-situ particle monitor (ISPM) and particle beam mass spectrometer (PBMS) which installed in the reactor exhaust line. The particle current and number count are monitored at set-up, stabilize, deposition, purge and pumping process step in real-time. The particle number distribution at stabilize step was measured using PBMS and compared with SEM image data. The PBMS and SEM analysis data shows the 110 nm and 80 nm of mode diameter for BPSG and PSG process, respectively.

• 한국진공학회:학술대회논문집
• /
• 한국진공학회 2009년도 제38회 동계학술대회 초록집
• /
• pp.261-261
• /
• 2010

본 연구에서는 PBMS (Particle Beam Mass Spectrometer)와 ISPM (In-Situ Particle Monitor)을 연계하여 BPSG (Borophosphosilicate Glass) 및 PSG (Phosphosilicate Glass) 박막 증착을 위한 CVD (chemical vapor deposition) 공정 중 발생하는 오염입자 발생특성에 대해 비교 평가하였다. 소스는 TEB (Triethylborate), TEPO (Triethylphosphate) 및 TEOS (Tetraethoxysilane)를 사용하였고, 운반가스 및 반응가스로 He과 $O_2$ 및 $O_3$를 사용하였다. 증착온도와 압력은 각각 $450^{\circ}C$, 200 Torr 이었다. 반응기의 배기라인에 PBMS와 ISPM을 설치하고 500 nm 이하의 입자에 대해 공정단계별 시간에 따른 모니터링 결과 전 공정에 걸쳐 동일한 패턴의 입자발생분포를 보였으며, 특히 PBMS의 경우 ISPM의 입자측정한계인 260 nm 이하의 입자크기도 측정할 수 있었다. 입자발생이 안정적으로 일어나는 증착공정 중 PBMS를 통하여 입자크기를 측정한 결과 BPSG의 경우 약 110 nm, PSG의 경우 약 80 nm의 분포를 나타내었다. 이를 통해 TEB 소스가 배제된 PSG의 경우 BPSG의 경우보다 입자의 성장이 지체됨을 확인하였다. 측정에 대한 신뢰성을 확보하기 위해 PBMS 내의 TEM (Transmission Electron Microscopy) grid를 이용하여 입자를 샘플링 하였고, TEM 분석을 실시한 결과 PBMS 측정결과와 잘 일치하였다. 또한 EDS (Energy Dispersive Spectroscopy) 분석을 통하여 입자성분에 대해 검증하였다.