• Proceedings of the IEEK Conference
• /
• 1998.06a
• /
• pp.807-810
• /
• 1998

This paper presents BIST (Built-in self-test) techniques for detection of path delay faults in digital circuits. In the proosed BIST schemes, the shift registers make possible to concurrently generate and compact the latched test data. Therefore the test time is reduced efficiently. By reordering the elements of th shifte register based on the information of the hamming distance of each memory elements in CUt, it is possible to increase the number of path delay faults detected robustly/non-robustly. Experimental results for ISCAS'89 benchmark circuits show the efficiency of the proposed BIST techniques.

• The Journal of the Acoustical Society of Korea
• /
• v.18 no.1
• /
• pp.67-71
• /
• 1999

In this paper, we design circuits embedded in memory chip which perform memory testing algorithms using BIST scheme to reduce testing time and cost for testing. In order to implement circuits for MSCAN, Marching and checkerboard test algorithms, which have widely used in memory testing, we survey structure of the BIST circuits and describe each block of BIST circuits by using VHDL. Thereafter, We verify behavior of each VHDL coding block and extract BIST circuits for target testing algorithms by CAD tool for simulation and synthesis. Extracted circuits have very low area overhead.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.39 no.8
• /
• pp.24-33
• /
• 2002

For mixed signal circuits that integrate both analog and digital blocks onto the same chip, testing the mixed circuits has become the bottleneck. Since most of mixed signal circuits are functionally tested, mixed signal testing needs expensive automatic test equipments for test input generation and response acquisition. In this paper, a new efficient BIST is developed which can be used for mixed signal circuits. In the new BIST, only faults on embedded resistances, capacitances and its combinations are considered. To guarantee the quality of chips, the new BIST performs both voltage testing and phase testing. Using these two testing modes, all the faults are detected. In order to support this technique, the voltage detector and the phase detector are developed. Experimental results prove the efficiency of the new BIST.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.8 no.2
• /
• pp.449-455
• /
• 2004

This paper presents a novel defect detection method for one chip RF front end with fault detection circuits using input matching measurement. We present a BIST circuit using 40.25{\mu}m$ CMOS technology. We monitor the input transient voltage of the RF front end to differentiate faulty and fault-free RF front end. Catastrophic as well as parametric variation fault models are used to simulate the faulty response of the RF front end. This technique has several advantages with respect to the standard approach based on current test stimulus and frequency domain measurement. Because DUT and fault detection circuits are implemented in the same chip, this test technique only requires use of digital voltmeter (RMS meter) and RF voltage source generator for simpleand inexpensive testing.

• The Transactions of the Korean Institute of Electrical Engineers D
• /
• v.49 no.6
• /
• pp.322-329
• /
• 2000

BIST(Built-in Self Test) has been considered as the most promising DFT(design-for-test) scheme for the present and future test strategy. The most serious problem in applying BIST(Built-in Self Test) into a large circuit is the excessive increase in test time. This paper is focused on this problem. We proposed a new BIST construction scheme which uses a parallel divide-and-conquer method. The circuit division is performed with respect to some internal nodes called test points. The test points are selected by considering the nodal connectivity of the circuit rather than the testability of each node. The test patterns are generated by only one linear feedback shift register(LFSR) and they are shared by all the divided circuits. Thus, the test for each divided circuit is performed in parallel. Test responses are collected from the test point as well as the primary outputs. Even though the divide-and-conquer scheme is used and test patterns are generated in one LFSR, the proposed scheme does not lose its pseudo-exhaustive property. We proposed a selection procedure to find the test points and it was implemented with C/C++ language. Several example circuits were applied to this procedure and the results showed that test time was reduced upto 1/2151 but the increase in the hardware overhead or the delay increase was not much high. Because the proposed scheme showed a tendency that the increasing rates in hardware overhead and delay overhead were less than that in test time reduction as the size of circuit increases, it is expected to be used efficiently for large circuits as VLSI and ULSI.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.30 no.4A
• /
• pp.328-335
• /
• 2005

bIn this paper, built-in self-repair(BISR) is proposed for semiconductor memories. BISR is consisted of BIST(Buit-in self-test) and BIRU(Built-In Remapping Uint). BIST circuits are required not oがy to detect the presence of faults but also to specify their locations for repair. The memory rows are virtually divided into row blocks and reconfiguration is performed at the row block level instead of the traditional row level. According to the experimental result, we can verify algorithm for replacement of faulty cell.

• Proceedings of the IEEK Conference
• /
• 2001.06b
• /
• pp.125-128
• /
• 2001

In this paper, we propose a low power Scan-based Built-ln Self Test based on circuit partitioning and pattern suppression using modified test control unit. To partition a CUT(Circuit Under Testing), the MHPA(Multilevel Hypergraph Partition Algorithm) is used. As a result of circuit partition, we can reduce the total length of test pattern, so that power consumptions are decreased in test mode. Also, proposed Scan-based BIST architecture suppresses a redundant test pattern by inserting an additional decoder in BIST control unit. A decoder detects test pattern with high fault coverage, and applies it to partitioned circuits. Experimental result on the ISCAS benchmark circuits shows the efficiency of proposed low power BIST architecture.

• Journal of the Institute of Electronics and Information Engineers
• /
• v.52 no.6
• /
• pp.70-76
• /
• 2015

This paper introduces an FPGA self-test architecture reusing FPGA boundary scan chain as self-test circuits. An FPGA boundary scan cell is two or three times bigger than a normal boundary scan cell because it is used for configuring the function of input/output pins functions as well as testing and debugging. Accordingly, we analyze the architecture of an FPGA boundary scan cell in detail and design a set of built-in self-test (BIST) circuits in which FPGA boundary scan chain and a small amount of FPGA logic elements. By reusing FPGA boundary scan chain for self-test, we can reduce area overhead and perform a processor based on-board FPGA testing/monitoring. Experimental results show the area overhead comparison and simulation results.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.27 no.1A
• /
• pp.66-72
• /
• 2002

In this paper, we implemented the GenJTAG, a CAD tool, which generates a code of boundary scan circuit supporing a board level testing and d BIST(Built-In Self Test) written in verilog-HDL. A boundary scan circuit code that supports user's own BIST instructions is generated based on the informations from the users. Most CAD tools hardly allow users to add their own BIST instructions because the generated code described in gate-level. But the GenJTAG generates a behavioral boundary scan circuit code so users can easily make a change on the generated code.

• JSTS:Journal of Semiconductor Technology and Science
• /
• v.2 no.3
• /
• pp.226-232
• /
• 2002

This paper explains a technique to improve the fault coverage of oscillation-test [1-5] for linear analog circuits. The transient behavior of the virtual ground is monitored during oscillation to extract information of the circuit. The limitation of the oscillation-test is analyzed, and an efficient signature analysis technique is proposed to maximize the fault coverage. The experimental result proves that the parametric fault coverage can be significantly increased by the proposed technique.