• Korean Journal of Breeding Science
• /
• v.41 no.3
• /
• pp.299-305
• /
• 2009

A new six-rowed naked barley cultivar "Jinjuchal" with high whiteness after cooking and high $\beta$-glucan content was developed from the cross between 'Jinmichapssalbori' with high winter hardiness, lodging tolerance, grain whiteness and pearling yield, and 'Suwon 333' with waxy endosperm by the Honam Agricultural Research Institute (HARI), NICS, RDA in 2007. An elite line, SB962002G-B-B-B-84-4 was selected in 2002 and designated as 'Iksan 79' It showed good agronomic performance in the regional yield trials (RYT) from 2005 to 2007 and was released with the name of "Jinjuchal" possessing high whiteness and low proanthocyanidin waxy endosperm. The average heading and maturing dates of "Jinjuchal" were April 27 and June 1 in paddy field, which were same and one day later than those of the check cultivar 'Saechalssalbori' respectively. The new cultivar, "Jinjuchal" had 81 cm of culm length that was 1cm longer than that of 'Saechalssalbori' and 4.9 cm of spike length. It showed 673 spikes per $m^2$, 56 grains per spike, 27.0 g of 1,000-grain weight, and 752 g of test weight. "Jinjuchal" showed stronger hardiness and better resistance to powdery mildew and BaYMV (Barley yellow mosaic virus) than those of the check cultivar, 'Saechalssalbori' It showed higher $\beta$-glucan content(8.4%) and water absorption rate than those of the check cultivar, 'Saechalssalbori' Its average yield of the pearled grain in the regional yield trial was 3.79 MT/ha in upland, and 3.73 MT/ha in paddy field, which were 1% lower and 3% higher than those of the check cultivar, respectively. Total phenol and proanthocyanidin contents were 4.2 and 0.2 mg/g, respectively. This cultivar is suitable for the area of the daily minimum temperature above $-6^{\circ}C$ in January in Korean peninsula.

• Korean Journal of Materials Research
• /
• v.5 no.2
• /
• pp.151-156
• /
• 1995

Low temperature firing $(Ba, Sr)TiO_{3}$ dielectrics were successfully prepared with lead based glass and those electrical properties were investigated. Different amount of PbO content glass materials were added to dielectrics to investigate the sinterability and its dielectric properties. Also, various compositions of ceramic capacitors were prepared to applicate in multilayer ceramic capacitors. A large amount of experiment has been done with various Pb contented glasses and different sintering temperatures. The sintering temperature of $(Ba,Sr)TiO_{3}$can be reduced from $1350^{\circ}C$to as low as $1050^{\circ}C$ with 4wt% addition of $PbO-ZnO-B_{2}O_{2}$ glass materials. Its dielectric constant at room temperature was up to 8100 with low dielectric loss, 0.005. This ceramic capacitor showed fully fired microstructures with its grain size of 1-3$\mu \textrm{m}$. The sintered body which was sintered at $1150^{\circ}C$ for 2hr with 4wt% $PbO-ZnO-B_{2}O_{2}$ glass material addition satisfied the Z5U specification of the EIAS.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2008.11a
• /
• pp.189-189
• /
• 2008

Due to the environmental issue vast research is going on to replace the widely used lead contented piezoelectric materials. Bismuth sodium titanate (abbreviated as BNT) based bismuth sodium titanate-barium titanate (abbreviated as BNBT) ceramic was prepared by using modified method rather than conventional mixed oxide method. This modification was made to improve the properties of BNT based ceramic. In this procedure $BaTiO_3$ (abbreviated as BT) was prepared using conventional mixed oxide method. Analytical grade raw materials of $BaCO_3$ and $TiO_2$ were weighted and ball milled using ethanol medium. The mixed slurry was dried and sieved under 80 mesh. Then the powder was calcined at $1100^{\circ}C$ for 2 hours. This calcined BT powder was used in the preparation of BNBT. Stoichiometric amount of $Bi_2O_3$, $Na_2CO_3$, $TiO_2$ and BT were weighted and mixed by using ball mill. The used calcination temperature was $850^{\circ}C$ for 2 hours. Calcined powder was taken for another milling step. BNBT disks were pressed to 15 mm of diameter and then cold isostatical press (CIP) was used. Pressed samples were sintered at $1150^{\circ}C$ for 2 hours. The SEM microstructure analysis revealed that the grain shape of the sintered ceramic was polyhedral and grain boundary was well matched where as the sample prepared by conventional method showed irregular arrangement and grain boundary not well matched. And sintered density was better (5.78 g/cc) for the modified method. It was strongly observed that the properties of BNBT ceramic near MPB composition was found to be improved by the modified method compare to the conventional mixed oxide method. The piezoelectric constant dB of 177.33 pC/N, electromechanical coupling factor $k_p$ of 33.4%, dielectric constant $K_{33}^T$ of 688.237 and mechanical quality factor $Q_m$ of 109.37 was found.

• Progress in Superconductivity
• /
• v.14 no.1
• /
• pp.71-75
• /
• 2012

For the practical application of a YBCO superconductor bulk magnet, the superconductor bulk magnet with strong and stable magnetic field on a large area surface should be fabricated. To satisfy these requirements, we have designed a conduction-cooled bulk magnet system using six single grain YBCO bulk superconductors. Six rectangular-shaped YBCO bulk superconductors with a dimension of $38{\times}38{\times}15mm^3$ were field-cooled at 20 K using a superconductor magnet with maximum operating magnetic field of 4 T. The magnetic flux of 3.0 T and 2.8 T were achieved on the surface of bulk superconductors and over the vacuum chamber surface of the refrigerator, respectively.

• Korean Journal of Crystallography
• /
• v.13 no.3_4
• /
• pp.165-171
• /
• 2002

Single phase $Pb(Fe_{1/2}Ta_{1/2})O_3$, ceramics were successfully synthesized from the powders prepared by solid state reaction (sintering temperature: $1100^{\circ}C$, density: $9.3g/cm^3$, average grain size: $5.1{\pm}1.2mm$, space group: Pm3m). Their dielectric properties measured at $-150{\sim}50^{\circ}C$ showed the maximum relative dielectric constant of 31000 at $-41^{\circ}C$. 1 kHz, and typical relaxor ferroelectrics characteristics such as diffuse phase transition and dielectric relaxation phenomena. However, the diffuseness of phase transition decreased and the dielectric properties became more normal ferroelectrics as the time of annealing at $1000^{\circ}C$ increased. By using Raman spectroscopy, it was revealed that the $Fe^{3+}$ and $Ta^{5+}$ ions in the as-sintered $Pb(Fe_{1/2}Ta_{1/2})O_3$, are stoichiometrically 1 : 1 ordered within the short-range that can not be probed even by transmission electron microscopy, and this stoichiometric 1 : 1 ordering is enhanced by the annealing. The relaxor ferroelectric characteristics in the as-sintered $Pb(Fe_{1/2}Ta_{1/2})O_3$, could be correlated with the stoichiometric 1 : 1 short-range ordering of B-site cations, and the decrease of relaxor ferroelectric characteristics in the annealed $Pb(Fe_{1/2}Ta_{1/2})O_3$ could be correlated with the enhanced stoichiometric 1 : 1 short-range ordering of B-site cations.

• Proceedings of the KIEE Conference
• /
• 2007.07a
• /
• pp.1283-1284
• /
• 2007

The barium strontium calcium titanate((Ba,Sr,Ca)$TiO_3$) powders prepared by the sol-gel method and $MnCO_3$ as acceptor were mixed oxide method. The microstructure was investigated with variation of $Pr_{2}O_{3}$ amount. The BSCT powder and $Pr_{2}O_{3}$ were mixed with organic vehicle(Ferro. B75001). BSCT thick films were fabricated by the screen-printing method on alumina substrates. The bottom electrode was Pt and upper electrode was Ag, respectively. All BSCT thick films were sintered at $1420^{\circ}C$, for 2h. The result of the differential thermal analysis(DTA), exothermic peak at around $654^{\circ}C$ due to the formation of the polycrystalline perovskite phase. In the X-ray diffraction(XRD) patterns, all BSCT thick films showed the typical perovskite polycrystalline structure and no pyrochlore phase was dbserved. The microstructure investigated by scanning electron microscope(SEM). Pore and grain size of BSCT thick films were decreased with increasing amount of $Pr_{2}O_{3}$ dopant. And the average grain size and thickness of BSCT thick films doped with 0.1 mol% $Pr_{2}O_{3}$ was $3.09{\mu}m$, $60{\mu}m$, respectively. The relative dielectric constant decreased and dielectric loss decreased with increasing amount of $Pr_{2}O_{3}$ dopant, the values of the BSCT thick films no doped with $Pr_{2}O_{3}$ were 7443 and 4 % at 1 kHz, respectively.

• Current Photovoltaic Research
• /
• v.1 no.2
• /
• pp.109-114
• /
• 2013

$Cu_2ZnSnS_4$ (CZTS) nanoparticles were synthesized by a solvothermal method using copper (II) acetate, zinc acetate, tin chloride, and sulfur in diethylenetriamine solvent. Binary sulfide particles such as CuS, ZnS, SnS, and $SnS_2$ were obtained at $180^{\circ}C$; single-phase CZTS nanoparticles were obtained at $280^{\circ}C$. CZTS nanoparticles with spherical shape and grain size of 40 to 60 nm were obtained at $280^{\circ}C$. In the middle of 180 and $280^{\circ}C$, CZTS and ZnS phases were found. The time variation of reaction at $280^{\circ}C$ revealed that an amorphous state formed first instead of binary phases and then the amorphous phase was converted to crystalline CZTS state; it is different reaction path way from conventional solid-state reaction path of which binary phases react to form CZTS. CZTS films deposited and annealed from single-phase nanoparticles showed porous microstructure and poor adhesion. This indicates that a combination of CZTS and other flux phase is necessary to have a dense film for device fabrication.

• Transactions on Electrical and Electronic Materials
• /
• v.18 no.6
• /
• pp.330-333
• /
• 2017

$Co_xMn_{3-x}O_4$ ($1.48{\leq}x{\leq}1.63$) ceramics were fabricated using the solid-state reaction method. Structural and electrical properties of specimens based on the composition ratio of Co were observed in order to investigate their applicability in NTC thermistors. All specimens showed a single spinel phase with a homogeneous tetragonal structure. The $Co_{1.57}Mn_{1.43}O_4$ specimen showed a maximum average grain size of approximately $6.47{\mu}m$. In all specimens, TCR properties displayed excellent characteristics of over $-4.2%/^{\circ}C$. The resistivity at 298 K and B-value of the $Co_{1.57}Mn_{1.43}O_4$ specimen were approximately $418{\Omega}-cm$ and 4300, respectively.

• Journal of the Korean Magnetics Society
• /
• v.8 no.2
• /
• pp.62-66
• /
• 1998

We have studied on the magnetic properties of the specimen with additives Bi$_2$O$_3$and$V_2O_5$ that sintered at 900 $^{\circ}C$ for 4 hours for sybthesizing optimal Ni-Zn-Cu ferrite. Curie temperature rises from 240 $^{\circ}C$ to 270 $^{\circ}C$ as Ni contents increase. Magentic maximum induction$(B_m)$ increases from 2650 G to 3300 G, 3500 G in the specimens with $V_2O_5$ and Bi$_2$O$_3$resectively. On the contrary coercive force $(H_c)$ lowers to 2.05 Oe~1.05 Oe. Permeability all increase in the specimen with additives. In the specimen with additive Bi$_2$O$_3$, we have obtained the low relative loss factor of $6.3{\times}10^{-5}~7.84{\times}10^{-5}$ in the range of 1MHz due to increase of resistivity in grain boundary. In the specimen with additive $V_2O_5$ in spite of increase permeability relative loss factor increase of due to decrease of Q-value.

• Journal of the Korean association of regional geographers
• /
• v.13 no.4
• /
• pp.409-421
• /
• 2007

The purpose of this paper is to consider the formation processes and depositional conditions of bars formed at the upper-stream part of Sayeon Dam since Sayeon Dam construction in 1964. Results of analyzing the shape characteristics of bars and their sediment grain size distribution are as follow: Firstly, bars are able to categorized as subaqueous bars (A, B), mid-channel bars(C, D), and tributary side-bars(E). Secondly, the outline of bars has longish along the flow path, and their height lowers more and more going towards downstream. Also the height of bar surface tend to heighten from flow path to mountain slope. However, the near part of A is comparatively higher than its distant part, A is defined as a subaqueous natural levee and back swamp. Thirdly, the average particle size of A and B become smaller toward mountain slope. In transportation style, ratio of suspended load become higher toward mountain slope. Fourthly, sorting is worse to very worse according with lake's random changable water level. Fifthly, bar A and B were formed by vertical sedimentation of sediments according as sediments transported along flow path in the subaqueous conditions were spreaded out of flow path. C and D were formed by bed load as flood level lowered. And E was formed by vertical sedimentation while stream flow stopped in tributary's mouth areas with the water level heightening.