• 드라이브 ㆍ 컨트롤
• /
• 제17권2호
• /
• pp.9-18
• /
• 2020

The purpose of this study was to analyze the effect of the soil cone index (CI) on the tractor work load. A load measurement system was constructed for measuring the field data. The field sites were divided into grids (3×3 m), and the cone index was measured at the center of each grid. The work load measured through the plow tillage was matched with the soil cone index. The matched data were grouped at 600 kPa intervals based on the cone index. The work load according to the cone index was analyzed for engine, axle, and traction load, respectively. The results showed that when the cone index increased, engine torque decreased by up to 9%, and the engine rotational speed and brake-specific fuel consumption increased by up to 5% and 3%, respectively. As the cone index increased, the traction and tillage depth were inversely proportional to the cone index, decreasing 7% and 18%, respectively and the traction and tillage depth were directly proportional to the cone index, increasing 13% and 12%, respectively. Thus, it was found that the cone index had a major influence on the engine, axle, and traction loads of the tractor.

• 한국전자통신학회논문지
• /
• 제6권6호
• /
• pp.873-880
• /
• 2011

최근 환경오염, 지구 온난화, 화석 연료 고갈 등이 범지구적 문제가 됨에 따라 녹색 에너지 기술 개발이 주목을 받고 있다. 이런 추세에 따라, 자전거가 다양한 스마트 에너지 기술과 결합하여 친환경 근거리 이동수단으로 발전하고 있다. 스마트 자전거 기술과 관련하여 많은 기술이 개발되고 있는데 이중 PAS(Power Assist System)는 사람의 힘과 전기의 힘을 효과적으로 결합하여 배터리로 구동되는 전기 모터를 제어하는 기술이다. 본 논문은 PAS를 구성하는 핵심 기술인 새로운 토크 센서를 제안한다. 이 기술은 기존 기술들과는 달리 자전거 뒤축에 스트레인 게이지를 부착하여 슬립링의 필요성을 없애고 사람에 의해 가해지는 구동축 토크를 측정 할 뿐 아니라, 현재 작동되는 기어의 위치를 근사적으로 추정 가능하게 한다.

• 제어로봇시스템학회논문지
• /
• 제16권7호
• /
• pp.632-638
• /
• 2010

This paper presents an optimum tire force distribution method for 6WD/6WS(6-Wheel-Drive and 6-Wheel-Steering) electric vehicles. Using an independent steering and driving system, the performance of 6WD/6WS vehicles can be improved, as, for example, with respect to their maneuverability under low speed and their stability at high speed. Therefore, there should be a control strategy for finding the optimum tire forces that satisfy the driver's command and minimize energy consumption. From the driver's commands (steering angle and accelerator/brake pedal stroke), the desired yaw moment, the desired lateral force, and the desired longitudinal force were obtained. These three values were distributed to each wheel as the torque and the steering angle, based on the optimum tire force distribution method. The optimum tire force distribution method finds the longitudinal/lateral tire forces of each wheel that minimize the cost function, which is the sum of the normalized tire forces. Next, the longitudinal/lateral tire forces of each wheel are converted into the reference torque inputs and the steering wheel angle inputs. The proposed method was tested through a simulation, and its effectiveness was verified.

• Journal of Biosystems Engineering
• /
• 제36권2호
• /
• pp.79-88
• /
• 2011

The purpose of this study was to analyze power requirement of an agricultural tractor by major field operations. First a survey was conducted to obtain annual usage ratio of agricultural tractor by field operation. Plowing, rotary tillage, and loader operations were selected as major field operations of agricultural tractor. Second, a power measurement system was constructed with strain-gauge sensors to measure torque of four driving axles and a PTO axle, speed sensors to measure rotational speed of the driving axles and an engine shaft, pressure sensors to measure pressure of hydraulic pumps, an I/O interface to acquire the sensor signals, and an embedded system to calculate power requirement. Third, the major field operations were experimented under fields with different soil conditions following planned operation paths. Power requirement was analyzed during the total operation period consisted of actual operation period (plowing, rotary tillage, and loader operations) and period before and after the actual operation (3-point hitch operating, forward and reverse driving, braking, and steering). Power requirement of tractor major components such as driving axle part, PTO part, main hydraulic part, and auxiliary hydraulic part were measured and calculated to determine usage ratio of agricultural tractor power. Results of averaged power requirement for actual field operation and total operation were 23.1 and 17.5 kW, 24.6 and 19.1 kW, and 14.9 and 8.9 kW, respectively, for plowing, rotary tillage, and loader operations. The results showed that rotary tillage required the greatest power among the operations. Averaged power requirement of driving axles, PTO axle, main hydraulic part, and auxiliary part during the actual field operation were 8.1, 7.8, 3.4, and 1.5 kW, respectively, and the total requirement power was about 70 % (20.8 kW) of the rated power. Averaged power requirement of driving axles, PTO axle, main hydraulic, and auxiliary hydraulic for the total operation period were 6.5, 6.0, 2.1, 0.9 kW, respectively, and total requirement power was about 52 % (15.5 kW) of the rated power. Driving axles required the greatest amount of power among the components.

• 한국소음진동공학회논문집
• /
• 제15권7호
• /
• pp.865-870
• /
• 2005

Torque fluctuation of the engine and angular velocity variation of propeller shaft is the main excitation source for torsional vibration in the vehicle driveline. Experimental model for engine system is constructed with 4 cylinder 4 cycle diesel engine including Motor-Propeller Shaft-Axle-Wheel system. The angular velocity is measured by magnetic pickup and FV converter at the engine flywheel and propeller shaft. This paper presents the theoretical mechanism of these excitation sources and it is identified by the experimental methods.

• 전기학회논문지
• /
• 제63권12호
• /
• pp.1759-1763
• /
• 2014

In this paper, we were performed a structural analysis and durability analysis for an integral frame with an axle according to development of the electric locomotive traction motor. In terms of the structural stability, as a result of the analysis modeling with coupling conditions of beam element and an alternative element of three-dimensional, the maximum von-Mises stress of the locking screw mounting frame were similar as 50MPa and 51MPa. Also A comparison of the natural frequency and the exciting frequency while driving of the electric locomotive No. 8200, the natural frequency is 627.05Hz~856.9Hz while the exciting frequency is not more than most 30Hz or 553Hz, 1110Hz. Therefore, it is possible to avoid the resonance.

• 한국생산제조학회지
• /
• 제21권6호
• /
• pp.897-902
• /
• 2012

Low speed vehicle(LSV), golf carts have unique requirements to differential gear design. For double axle torque LSV differential loading conditions were determined with the help of analytical model and ANSYS finite element analysis. With stress safety factor 3.15, fatigue safety factor 1.08 and fatigue life 106 cycle ring gear teeth strength analysis is performed and structure design optimized. This allows reducing overall cost of differential unit.

• 전기학회논문지
• /
• 제57권8호
• /
• pp.1371-1376
• /
• 2008

A Steer-by-Wire system has so many advantages comparing with conventional mechanical steering system that it is expected to take key role in future environment friendly vehicle and intelligent transportation system. The mechanical connection between the hand wheel and the front axle will become obsolete. SBW system provides many benefits in terms of functionality, and at the same time present significant challenges - fault tolerant, fail safety - too. In this paper, failure analysis of SBW system will be performed and than sensor fusion technique will be proposed for fail safety of SBW system. A sensor fusion logic of steering angle sensor by using steering angle sensor, torque sensor and rack position sensor will be developed and simulated by fault injection simulation.

• Journal of Biosystems Engineering
• /
• 제2권1호
• /
• pp.25-32
• /
• 1977

This experiment was conducted in order to find out the drawing performance of a two-wheel tractor under different levels of the soil moisture and hardness, so as to obtain some basic data for improving their drawing performance. With fairly homogeneous soil, 5 levels of soil moisture contents (8, 13, 17, 20 and 23%) and 3 levels of soil hardness (0 , 2 and 4kg/$cm^2$) were selected for this experiment.The summerized results are as follows ;1. The draft force, on the hard soil (hardness ; 4kg/$cm^2$), had a distinct tendency to decrease with the increasing soil moisture. On the medium soil (hardness ; 2 kg/$cm^2$), and the soft soil (hardness ; 0kg$cm^2$), the draft force showed the highest when the moisture contents were within the range of 16-19%.But the maximum draft force, on the soft soil, was higher than that on the medium soil by 10 %. 2. The driving axle torque increased with increasing soil by 10 %. 3.The values of horizontal distance between the soil reaction point and axle shaft were within the range of 0~10cm , and it had the tendency to increase with the increasing soil moisture. Also, it s value was the largest on the hard soil and the smallest on the soft soil. 4.The tractive efficiency decreased with the increasing soil moisture. On the hard soil, the average value of tractive efficiency was higher than that on the medium soil by 19.0% and that on the soft soil was lower than that on the medium soil. 5.The traction ratio were within the range of 30 ~45%, and their changing tendency with respect to the soil moisture was similar to that in the case of the draft force. 6. The travel resistance ratio tended to increased with increasing soil moisture, and the highest value was found on the soft soil, and the lowest on the hard soil.

• 한국정보전자통신기술학회논문지
• /
• 제11권2호
• /
• pp.150-155
• /
• 2018

국내 논 작업의 기계화율은 약 90% 이상 되었지만, 밭 작업의 기계화율은 약 60%이며, 수확작업의 기계화율은 10%내외로 밭 작업의 기계화율의 제고가 필요한 실정이다. 그러므로 본 연구는 트랙터 부착 수확작업기 개발을 위한 기초연구로써 마늘, 양파 등 땅속작물수확기의 견인작업에 따른 트랙터 차축의 부하 신호를 측정하고 주행속도에 따른 차축 소요 동력을 분석하였다. 밭 작업용 트랙터 차축의 소요 동력을 측정하기 위하여 휠 센서와 데이터 수집 시스템을 설치하였으며, 두 개의 작업속도에서 견인작업을 수행하며 소요 동력을 계측하였다. 계측한 데이터는 일원 분산분석을 수행하여 트랙터 주행 속도가 차축 소요 동력에 미치는 영향을 분석하였다. 소요 동력 분석 결과, 트랙터 부착 작업기의 작업속도가 증가할수록 트랙터의 소요 동력이 증가됨을 알 수 있었으며, 트랙터 동력전달시스템의 최적설계를 위해서는 다양한 수확작업에 따른 소요동력 분석이 필요함을 알 수 있다.