• 한국기계가공학회지
• /
• 제11권1호
• /
• pp.88-94
• /
• 2012

An axle drive shaft with double joint shaft, cross kit and yoke has an important role by transferring power and changing steering angle between axle and wheel in power train system. It has been used widely in the heavy machinery requiring a high reliability in the power train system. At fatigue failures of the axle drive shaft with the long span, a relatively high stress concentration at a snap ring groove on the drive shaft brings to significant fatigue damages under repeated loading condition. As Peterson's suggestions on this study, a relief groove in the vicinity of the snap ring groove is applied by decreasing the stress concentration and improving the fatigue life of axle drive shaft. By using FEM analysis, the decreasing effect of the stress concentration and extended fatigue life are due to the change of design parameters related with size and location of the relief groove. The relief groove with the design parameters such as d/b=2.0 and r/h=1.2 enables to decrease the stress concentration of 22.3% and increase the fatigue life more than 3 times by comparing with no relief groove application.

• Tribology and Lubricants
• /
• 제29권6호
• /
• pp.397-402
• /
• 2013

This study examined the tribological characteristics of the drive shaft and axle system in vehicles. The first drive shaft example contained end play for a CV joint that transferred part of the transmission power to the wheel. The joint part of the drive shaft was deformed because of reduced durability due to wear. Thus, vibrations caused the body to shake and become unbalanced when the drive shaft transferred the power. The second example was the cross-section of a shaft that connected the slip-connection of the propeller shaft on the input side to the yoke flange of the output side; the durability was reduced because of corrosion. End play caused by wear between the bearing and cross-section shaft appeared to cause shaking. In the third example, a grease leak reduced lubrication and thus caused damage to the hub bearing and inside the knuckle. The failure was produced by sticking. The fourth example had noise produced by the gear and gear transfer. This was due to the backlash of the pinion and few ring gears for the differential gear. Therefore, drive shaft and axle systems must be thoroughly checked and managed to minimize and reduce failure phenomena.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2006년도 춘계학술대회논문집
• /
• pp.309-313
• /
• 2006

Many researchers have studied on the lightness of automobile. These researches are such as a body shell, sub frame, fuel tank, engine etc. The transmission Part is a magnitude one in the aspect of weight. A drive shaft (propeller shaft) transmits the engine power to rear differential gear assembly. It is used in the compact car that is a single drive shaft. But in the case of long body cars such as SUV (Sports Utility Vehicle), truck and large vehicle, two or three divided drive shaft are used to prevent the vibration damage from a drive shaft that has been taken high torsion and rotation. This multi-divided drive shaft structure is so heavy because it is assembled by yoke, center bearing and solid spline axis. When the rear axle move up and down, the spline shaft adjust the variation of a length between the transmission and rear axle gearbox. In this paper, it is studied in the experimental method that is a bending vibration characteristic of slip in tube shaped propeller shaft. This type propeller shaft is developed to combine the spline axis with drive shaft and can be light in weight of transmission part.

• 대한기계학회논문집A
• /
• 제34권3호
• /
• pp.273-281
• /
• 2010

본 논문은 교정가속수명시험법을 이용하여 액슬구동축의 피로수명을 예측하는 법을 제안한다. 교정가속 수명시험법은 수명예측, 시험시간 절감, 신뢰성 정량화시에 매우 효과적이다. 피로시험은 두 개의 고 부하 수준과 한 개의 저 부하 수준에서 수행되고, 외삽법을 사용하여 사용수준에서의 수명시간을 예측하게 된다. 본 논문에서는 수행시험 결과로부터 획득한 수명시간, 가속지수, 형상모수, 척도모수등과 같은 주요 신뢰성 인자들을 보여주고 있다. 액슬구동축의 수명예측은 부하스펙트럼 데이터와 시험데이터와의 비교 연구를 수행하여 검증하였다. 교정가속수명시험법을 사용한 수명예측법은 짧은 시간내에 수명을 예측하는데 매우 효과적인 방법임을 확인하였다.

• 한국기계가공학회지
• /
• 제17권2호
• /
• pp.153-159
• /
• 2018

This paper suggests a way to improve the strength of the driveshaft, which is a vulnerable part of the drive axle system, for a 3.5-ton commercial vehicle. The driveshaft is composed of a universal joint with a spider and yoke, yoke shaft, etc. The driveshaft is developed by choosing design parameters for the spider and yoke such as the diameter and distance through the structural analysis of the driveshaft's components. Some driveshaft design cases have been made and analyzed with ANSYS; the strength of the driveshaft parts are validated from these results to propose an optimal design case. Finally, we suggest a driveshaft system that satisfies the working conditions for a 3.5-ton commercial vehicle.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2000년도 춘계학술대회논문집
• /
• pp.1894-1899
• /
• 2000

The Roadway caused through Power Train engine vibration and bad ride comfort. It is very important to analyze the vibratory characteristics. The mathematical models on the Power Train, which is composed of engine-/transmission block, universal joint shaft, differential, rear axle arm and wheels, are developed and is verified by the experiments. This Paper describes the coupling influence occurred through a complete drive system for the power train. Dies study is carried out computationally with a calculation program and experimentally with the aid of the mode analysis.

• Journal of Biosystems Engineering
• /
• 제27권3호
• /
• pp.203-210
• /
• 2002

In this study, the leveling control system for a tractor has been developed. The experimental model showed that the implementation of the proposed hydraulic control system fur the prototype design of a slope land tractor was feasible. The front axle was designed as a center pin type and the rear axle was designed as a trailing arm type. The leveling control of the body on the slope land was accomplished by controlling the height of the right and left trailing arms using the electronic controlled hydraulic cylinder. The maximum leveling control angles were ${\pm}$15$^{\circ}$ for roll angle and 7$^{\circ}$far pitch angle. The front and rear wheel drives were transmitted by gears from the main shaft to the final drive. The adaptability of the hydraulic control system was tested and investigated by analyzing the system response in time and frequency domain. The hydraulic control system on a step input showed a linearly increasing trend without any overshoot state. The hydraulic control system on a frequency input showed a little phase differences and gain drops within the range of 0.3Hz.

• 대한기계학회논문집A
• /
• 제40권11호
• /
• pp.979-986
• /
• 2016

등속조인트의 일종인 트리포드 축은 동력전달용으로 고속열차의 KTX와 KTX-산천에 모두 적용되고 있으며, 동력대차에서 모터 감속장치(MRU)와 차축 감속장치(ARU)를 연결해 고속회전동력을 전달하는 핵심 요소이다. 축 방향의 미끄럼 운동이 가능한 트리포드 축은 열차 구동을 위한 토크를 전달하며, 동력전달 시스템에 과토크 발생 시 축의 퓨즈부가 절단되어 동력을 차단한다. 본 연구에서는 리니어 액추에이터를 이용한 대용량 비틀림 시험장치의 개발과 이를 이용한 트리포드 축의 정적 비틀림 강도와 피로수명을 확인하고자 하였다. 또한 구조해석을 통해 축의 취약부를 파악하고 비틀림 피로해석 결과와 실제 피로시험의 결과를 비교분석하여 비틀림 성능 개선을 위한 설계안을 제시하고자 하였다. 한편 트리포드 축의 피로에 따른 열화를 파악하기 위해 히스테리시스 곡선을 이용하였으며, 히스테리시스 곡선의 기울기 변화를 통해 피로고장 시점을 확인하였다.

• 한국소음진동공학회논문집
• /
• 제24권8호
• /
• pp.592-599
• /
• 2014

A torsional vibration at driveline happens seriously at rapid vehicle acceleration. The torsional vibration at driveline can be reduced by optimization of joint angle and yoke phase angle of driveline. But, the joint angle of driveline is changed according to vehicle driving condition as acceleration, deceleration, forward and backward driving, so that excessive vibration is transmitted to vehicle body at specific driving condition. Especially under rapid acceleration condition, vibration transmitted to body could be maximized because excitation force at rapid acceleration is bigger than that at normal driving condition due to changed joint angle. The torsional vibration of driveline can be kept at low level by controlling suspension parameter to minimize rigid axle displacement as well as optimizing joint angles considering the vehicle acceleration condition.

• 농업과학연구
• /
• 제40권1호
• /
• pp.53-59
• /
• 2013

Analysis of load data during field operations is highly important for optimum design of power drive lines for agricultural tractor. Objective of the paper was to analyze field load data using FFT to determine frequency and the energy levels of meaningful cyclic patterns. Rotary tillage, plowing, baling, and wrapping operations were selected as major field operations of agricultural tractor. An agricultural tractor with power measurement system was used. The tractor was equipped with strain-gauge sensors to measure torque of four driving axles and a PTO axle, speed sensors to measure rotational speed of the driving axles and an engine shaft, pressure sensors to measure pressure of hydraulic pumps, an I/O interface to acquire the sensor signals, and an embedded system to calculate power requirement. In rotary tillage, calculated frequency was decreased as travel speed increased. In baler operation, calculated frequency was increased as PTO speed was increased. The calculated peak frequency levels and expected levels were similar. Results of the study would provide information on power utilization patterns and on better design of power drive lines.