• Transactions of the Korean Society of Automotive Engineers
• /
• v.21 no.3
• /
• pp.113-125
• /
• 2013

This study analyzes upper arm as the part of suspension through the structural analyses of fatigue. Maximum displacement is shown at the knuckle joint connected with the bracket of automotive body. Among the cases of nonuniform fatigue loads, 'SAE bracket history' with the severest change of load becomes most unstable but 'Sample history' becomes most stable. Maximum life at 'Sample history' or 'SAE transmission' can be shown with 60 or 3.5 times more than 'SAE bracket history' respectively. In case of 'Sample history' with the average stress of $-4{\times}10^4$ to $4{\times}10^4$ MPa and the amplitude stress 0 to $8{\times}10^4$ MPa, the possibility of maximum damage becomes 3%. This stress state can be shown with 5 or 6 times more than the damage possibility of 'SAE Bracket history' or 'SAE transmission'. This study result is applied with the design of upper arm and it can be useful at predicting prevention and durability against its damage.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.3 no.4
• /
• pp.19-29
• /
• 1995

This paper discusses the stick-slip phenomenon of the driveline system of a vehicle in consideration of friction. Friction is operated on the between of flywheel and clutch disk. The expressions for obtaining the results have been derived from the equation of motion of a three degree of freedom frictional torsion vibration system which is made up driving part(engine, flywheel), driven part(clutch, transmission) and dynamic load part(vehicle body) by applying forth-order Rungekutta method. It was found that the great affect parameters of the stick-slip or stick motion were surface pressure force between flywheel and clutch disk, time decay parameter of surface pressure force and 1st torsional spring constant of clutch disk when driveline system had been affected by friction force. The results of this study can be used as basic design data of the clutch system for the ride quality improvement of a car.

• Journal of the Korea Safety Management & Science
• /
• v.15 no.2
• /
• pp.71-77
• /
• 2013

The accident which is caused by the press work remains a Permanent obstacle in worker's hand or arms, the disaster ratio is high and the fatal case is many. Mainly Like this accident occurs because the hand to enter with inside of the press die, therefore, basic countermeasure is the safety press. In order to prevent access to mechanical moving part by the hand or any part of the body, it is important to making a safety die design Structurally. It presents the design of the safety press die with suitable structure in the Product's attribute which it had shown in samples, There is a possibility of being difficult because the attribute of safety die design that had present all the productions from research does not agree each other. but because the representative process which is used most at sample had designed, If you were imitates with safety die design base which is presented from this research, It comes to be thought to be the part which can are used at the various sides.

• Transactions of Materials Processing
• /
• v.7 no.6
• /
• pp.603-609
• /
• 1998

An aluminium sandwich sheet is the material fabricated by adhering two aluminum panels to one plastic core. When it has the same bending stiffness as an steel panel it is 65% lighter than steel panel and 30% lighter than aluminum panel. Therefore it is notified exclusively as good substitutive materials for steel body to improve fuel efficiency. An aluminium sandwich sheet, however, has a problem of the lower formability than steel in automotive application. In this paper we intend to develop application technologies of an aluminum sandwich sheet for auto body panels from selecting composed materials of aluminium sandwich sheets to fabricating prototype. We selected aluminium sandwich panels fabricated by Hoogovens company. Through formability tests we have designed the hood part on auto body panels and fabricated a mould and a prototype.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.20 no.5
• /
• pp.26-35
• /
• 2012

This paper investigates the influence on the aerodynamic performance of a passenger cruising very fast by some specific car body parts such as side mirrors, wheel arches and wheels designed hardly regarding aerodynamics. The magnitude of the contribution of each part is analyzed via on the CFD simulations. YF SONATA, a sedan of Hyundai Motors Company, plays a major role as the baseline car in this research, representing all passenger car. The CFD analysis condition consists of 6 different cases depending on whether each part exists or not. According to the CFD results, there were confirmed that additionally to the body parts' own drag, the car body went through somewhat the consequential increment of the drag by them. Among the 3 parts, wheel is the magnate that not only has the maximal drag but drives the drag of the passenger car to increase most steeply and the next is the side mirror.

• Journal of the Korean Institute of Gas
• /
• v.24 no.2
• /
• pp.9-14
• /
• 2020

This paper is a purpose to study the failure examples for a large bus vehicle fire. The first example, the researcher certified the fact that the absorbing material break away from the upper side of engine room because of weaken durability and the fire was produced in engine. The second example, it sought the fact that the fire breaks out by electric short because of over-load of compressor. The third example, it found the fact that the fire took place by heating of bellows upper part that was connected with muffler and exhaust manifold. The fourth example, it knew the fact that the fire occurred because of the electric short inside junction box of crash body part that was located to driver seat rightside. Therefore, the fire of a large bus occurring by decrepit of absorbing material and electric short have to thoroughgoingly manage the damage and dangerousness if it happens.

• Journal of the Korean Society of Mechanical Technology
• /
• v.13 no.1
• /
• pp.105-112
• /
• 2011

Increasing needs for light weight and high safety in modern automobiles induced the wide application of high strength steels in automotive body structures- The main difficulty in the forming of sheet metal parts with high strength steel is the large amount of springback including sidewall curl and twist in channel shaped member parts- Among these shape defects, twist occurs frequently and requires numerous reworks on the dies to compensate the shape deviation- But until now, it seems to be no effective method to reduce the twist in the forming processes- In this study, a new forming process to reduce the twist deformation during the forming of automotive structural member was suggested- This method consists of forming and restriking of embosses on the sidewall around the stretch flanging area of the part- and was applied in the forming process design of an automotive front side inner member with high strength steel- To evaluate the effectiveness of the method, springback analysis using $Pamstampa^{tm}$ was done- Through the analysis results, the suggested method was proven to be effective in twist reduction of channel shaped parts with stretch flanging area.

• Journal of the Korea Convergence Society
• /
• v.10 no.11
• /
• pp.321-326
• /
• 2019

As the use of public transportation increases, many researches are being carried out to increase the fuel economy of car. The goal of this study is to design a front body in order to increase the fuel economy of car through three models of cars. All models were designed with CATIA program and the flow analyses on the air outside car by model were carried out with ANSYS program. At the driving speed of 90km/h, the longer the body, the less air resistance it received. So, it is thought that there is the effect to increase fuel economy. Through this study, it can be helpful to design the front car body that can maximize train efficiency. By utilizing the design data on flow analysis according to the position of radiator inside car in this study, the esthetic sense can be given by being grafted onto the real automotive part.

• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.12 no.6
• /
• pp.52-59
• /
• 2013

In this study, strength and durability are investigated using structural and vibration analyses on models 1 and 2 of a press in common use. Model 1 has a structure in which a punch is applied from the upper part to the lower part; however, model 2 a structure in which a punch is applied from the lower part to the upper part. Maximum displacements of models 1 and 2 are 0.018184 mm and 0.025498 mm, respectively. Maximum equivalent stresses of models 1 and 2 are 14.144 MPa and 18.58 MPa respectively. Maximum displacements are shown for the punches of both models; model 1 has less deformation than model 2. Model 1 has more durability than model 2, as determined by an investigation of the structural strength. Using natural frequency analysis, model 1 was found to have maximum deformation in the upper part of punch. Mode1 2 has its maximum deformation in the column part of the body and the upper part of the fixed pin. Using harmonic stress analysis, the maximum deformations were found on the punch part and column part of the body in the cases of models 1 and 2, respectively. As the maximum total deformation and equivalent stress in the case of model 2 are shown to become 40 times those values of model 1, the vibration durability of model 2 can be seen to be weaker than that of model 1.

• Transactions of the Korean Society of Machine Tool Engineers
• /
• v.17 no.5
• /
• pp.10-22
• /
• 2008

In an automotive body structure, a design configuration that fulfills structural requirements such as deflection, stiffness and strength is necessary for structural design and is composed of various components. The integrated design is used to obtain a minimum weight structure with optimal or feasible performance based on conflicting constraints and boundaries. The mechanical design must begin with the definition of one or more concepts for structure and specification requirements in a given application environment. Structural optimization is then introduced as an integral part of the product design and used to yield a superior design to the conventional linear one. Although finite element analysis has been firmly established and extensively used in the past, geometric and material nonlinear analyses have also received considerable attention over the past decades. Also, nonlinear analysis may be useful in the area of structural designs where instability phenomena can include critical design criteria such as plastic strain and residual deformation. This proposed approach can be used for complicated structural analysis for an integrated design process with the nonlinear feasible local flexibilities between system and subsystems.